NexiGo Warranty Registration | NexiGo
NexiGo | Home Theater Projectors & Video Collaborations
User Manual for NEXIGO models including: B10 Add On Baby Camera Unit, B10, Add On Baby Camera Unit, Baby Camera Unit, Camera Unit, Unit
NexiGo B10 Add-On Baby Camera Unit, 720P HD Resolution, 2-Way Audio, Pan-Tilt-Zoom, Temperature Detection, Night Vision, Lullaby Playing (Blue) : Electronics
File Info : application/pdf, 16 Pages, 8.59MB
DocumentDocumentUser Manual NexiGo ADD-ON BABY CAMERA UNIT B10 Register to get an EXTRA ONE year warranty. Only valid if registering within 14 days of product delivery. nexigo.com/warranty Welcome to the NexiGo Family! Thank you for choosing the NexiGo B10 Add-On Baby Camera Unit! You are now part of an exclusive club: the NexiGo family! It's our job to make sure you enjoy your membership. If you have any problems please contact us at cs@nexigo.com at any me for further assistance. This product is covered by our industry-leading 1-year manufacturer's warranty. Make sure to register your purchase at nexigo.com/warranty within 14 days of the delivery date to extend your warranty coverage to TWO Years! From all of us here at NexiGo, we want to welcome you again to the family. We thank you deeply for your trust and for your business. We know you'll love it here. We look forward to serving you again in the near future. Yours Sincerely, The NexiGo Team Contact Informaon: Website: www.nexigo.com Manufacturer: Nexight INC Email: cs@nexigo.com Tel: +1(458) 215-6088 Address: 11075 SW 11th St, Beaverton, OR, 97005, US - 1 - Product Descripon: The NexiGo B10 ADD-ON BABY CAMERA can be paired with the B200 Monitor only. It has a night vision mode so even in total darkness you can sll see what is going on in the room. And with features like temperature monitoring, and zoom with pan and lt opons, you can make sure that everything is exactly the way you want in your childs room. Finally, with built-in Lullaby's if you just are not able to get them to go to sleep you can put on the music and leave the room so they are not oversmulated and monitor them from a distance. The Nexigo B10 is here to help your sleep-addled brain and to make sure you always know exactly what is going on in your baby's room. What's in the Box? 1 x Video Baby Camera 1 x Camera Wall Bracket 1 x Mounng Screws Pack 1 x 3M Double-Sided Adhesive Tape 1 x Camera Power Adapter (5V / 1A) 1 x Camera Micro-USB Power Cable (3m) 1 x Instrucon Manual - 2 - Camera Diagram: 1 2 7 1 Wide-Angle Lens 2 Microphone 3 Speaker 3 6 45 4 Micro USB Port 5 Pairing Buon 6 Temperature Sensor 7 Antenna Specificaons: Product Name Model NexiGo Add-On Baby Camera Unit B10 - 3 - Transmission Range Power Input Nave Resoluon Working Temperature Storage Temperature Speaker 300~500 - Inside a standard home; 1000 - In an open area AC 5V / 1A 1280 x 720 -10°C ~ +50°C -20°C ~ +60°C 1W Seng up the Camera: 1. Plug the Camera Micro-USB Power Cable into the Camera, and then insert the other end of the cable into the Camera Power Adapter. 2. Plug the adapter into a power outlet. The Camera does not have a baery and requires a power connecon to funcon. - 4 - Connecon Instrucons: 1. Place the Camera within the operang range of the Monitor you've already had. 2. Press and hold the Power Buon on the right side of the Monitor for two seconds to turn it on. Power Buon MENU OK 3. Press Menu Buon and select Camera Sengs to enter the corresponding interface. - 5 - 4. Select Camera Pairing from the list below. Choose the Camera number you wish to add, then press OK Buon to confirm. Select Add to begin pairing. 5. Press and hold the Pairing Buon on the rear of the Camera unl a "beep" is heard. You must perform this step within 60 seconds aer starng the pairing process. - 6 - 6. A "Camera added successfully" noce will be displayed on the screen. The connecon is now acve. 7. You may repeat the process above for up to addional Cameras. Disconnecon Instrucons: 1. To disconnect a camera, navigate to: Menu > More Sengs > Camera Sengs. Select the Camera you wish to disconnect, then select Delete to disconnect the camera. - 7 - 2. If a Camera becomes disconnected unexpectedly for any reason, an alarm tone will play and the image below (or a similar one idenfying the specific camera that has been disconnected) will appear on the Monitor alerng you to which Camera has lost its connecon. Press any buon to stop the alarm. Mounng the Camera: Opon 1 - Use screws to secure the Camera Wall Bracket Consider the following factors when selecng a locaon to mount the camera: The mount can be posioned on a corner or on a flat surface. Do not mount this from a ceiling, it is not intended to hang and may become detached and fall. The camera must have an unobstructed view of the crib or bed from where it is mounted. The camera must have a nearby power outlet that can be reached without using an extension cord. - 8 - When a suitable locaon has been found that meets these criteria you may then begin the installaon process. 1) Posion the Camera Wall Bracket where you want it and locate the screw holes in the mount. Mark each hole carefully with a pencil / pen to ensure that the tapping process is accurate. a. For Corner Mounng b. For Flat Walls 2) Set aside the bracket and then drill a hole at least 6.0 mm deep at each mark. (Drill and drill bits NOT included.) 3) Insert a plasc wall anchor into each hole and hammer in the anchors so they are nearly flush with the wall surface. (Hammer NOT included.) 4) Place the bracket back on the wall in the chosen locaon and using the provided screws aach the bracket to the wall. Tighten the screws firmly. Ensure that you do not over-torque or strip the screw heads. - 9 - a. For Corner Mounng b. For Flat Walls Note: If mounng on a flat wall please make sure to mount this unit with the notch in the back facing upwards as shown below. DO NOT mount this unit with the notch facing any direcon other than up. 5) Align the Slide Locks on the Camera Wall Bracket with the holes on the boom of the Camera, then push the Camera body forward unl it gets stuck to secure it in place. - 10 - 6) Opmize your viewing angle by rotang the Camera manually, or ulize the remote pan and lt funcons with the Navigaon Buon on your Monitor. MENU OK Opon 2 - Use 3M Double-Sided Adhesive Tape to secure the Camera Wall Bracket Consider the following factors when selecng a locaon to mount the camera: The mount can only be posioned in a corner. The camera must have an unobstructed view of the crib or bed from where it is mounted. The camera must have a nearby power outlet that can be reached without using an extension cord. When a suitable locaon has been found that meets these criteria you may then begin the installaon process. 1) Adhere the 3M Double-Sided Adhesive Tape to both outer sidewalls of the Camera Wall Bracket as shown below. - 11 - 2) Posion the Camera Wall Bracket at the desired locaon and press firmly towards the wall. Ensure that both pieces of the tape are securely touching the wall. Push 3) Align the Slide Locks on the Camera Wall Bracket with the holes on the boom of the Camera, then rotate the Camera body to secure it in place. - 12 - 4) Opmize your viewing angle by rotang the Camera manually, or ulize the remote pan and lt funcons with the Navigaon Buon on your Monitor. MENU OK - 13 - Notes: Only use the charger provided by the manufacturer. Unauthorized chargers may cause damage to the products and void any warranty. Strangulaon Hazard: Cords may be a strangulaon hazard and should be properly stored out of reach of children. Never use extension cords with AC Adapters. Only use the AC Adapters provided with this product. Do not use or store the Camera in temperatures below 14°F or above 122°F (-10°C to 50°C). This product may be damaged by prolonged exposure to direct sunlight. If in direct sunlight ensure that it is shaded and has appropriate venlaon. FCC Requirement: Changes or modificaons not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against - 14 - harmful interference in a residenal installaon. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Increase the separaon between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. RF Exposure Warning Statements: This equipment complies with FCC radiaon exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body. Model: B10 FCC ID: 2AWDN-B10 facebook.com/nexigo1 Get in touch with FREE online services.