User Guide for MiBOXER models including: WL-433, 433MHz Gateway
The input voltage is DC5V/500mA, Please do not connect the power supply over DC5V, otherwise, the device will be broken easily.
1. The input voltage is DC5V/500mA, Please do not connect the power supply over DC5V, otherwise, the device will be broken easily. 2. Non-professional user cannot dismantle the divice
0345 Subordinate New Brand 433MHz Gateway Model No.: WL-433 1MFBTFSFBEUIFJOTUSVDUJPOTDBSFGVMMZ CFGPSFVTJOHUIFDPOUSPMMFS 1. Features Use LoRa SPSP Modem technology, compatible with MiBoxer 433MHz series products; and controlled by MiBoxer APP through WiFi or 4G network. Support DMX512(1990) control. Support third party voice control. Support Third Party Voice Control Can control MiBoxer 433MHz series product WiFi WiFi Wireless Control 433MHz RF 433MHz LoRa SPSP modem technology Smartphone App control Support DMX512(1990) control 16 Millions of colors to choose Color temperature 2700K~6500K Dim brightness/ Saturation Timing ON/OFF the lights One button learning Copy remote ID 2. Parameters Model No.: WL-433 Input: DC5V/500mA ( 5.5*2.1mm ) Working Temperature: -20~60^ Communication Mode: WiFi-IEEE 802.11b/g/n 2.4GHz Input Signal: DMX512(1990) RF: 433MHz ( Transmitting Power: 15dBm ) Modulation Method: LoRa spread spectrum Control Distance: 50m (Lamps into 0.5m under freshwater) Control Distance: 1000m (Lamps on the open area) Product Weight: 95g 48mm 27mm 118mm 30mm 182mm 3. Installation Please install the device within 50m as lights, and approaching the WiFi Router. 1PXFSJOQVU %.9 TJHOBMJOQVU DMX512 Control Panel 4. User Instruction 1. Install MiBoxer APP. Click" + " add devices( See details on MiBoxer APP instructions). 2. Click "433 Gateway" on the device list to enter control interface. 3. Click "Link/Unlink". Link/Unlink method, See details on APP link/unlink instruction. 4. After linking successfully, back to the control interface to control the lights randomly. Note: This gateway cannot group control. Mobile 10:18 Device List 433 Gateway 95% ON Mobile 10:18 433 Gateway 95% Set DMX %FWJDF (SPVQ %JTDPWFSZ Zone1 White Light Timer Link / Unlink Learning function: Gateway copy the remote ID to fulfill the gateway and remote ID no difference; after linking with remote, the gateway can control the lamps directly without linking again. 1. click "Learn" button, device indicating lamp blinking. 2, within 10 seconds, click any button on the remote, APP will hint learning successfully. Note: Just FUT086 433MHz remote support learning currently. Mobile 10:18 95% LLininkk/U/ Unlninlinkk Linking instruction: 1. Please select linking channel 2. Switch of the light; after 10 seconds, switch on again. 3. Press the linking button once within 3 seconds. 4. Link is done when the light blink 3 times slowly. Note: If the light doesn't blink slowly, Linking is failed. 1. Please check if the light is compatible with the remote. 2. Check if the light has been linked; The linked light cannot be linked again. 3. Please follow above steps to link again. Unlinking instruction: 1. Please select the linking channel 2. Switch of the light; after 10 seconds, switch on again. 3. Press the unlinking button once within 3 seconds. 4. Unlink is done when the light blink 10 times quickly. Note: If the light doesn't blink quickly, Unlinking is failed. 1. Please check if the light is compatible with the remote. 2. Check if the light has been linked; The unlinked light cannot be unlinked again. 3. Please follow above steps to unlink again. Zone1 Select zones Zone2 Zone3 Zone4 Zone5 Zone6 Zone7 Zone8 Learn Link Unlink Mobile 10:18 95% LLininkk/U/ Unlninlinkk Linking instruction: 1. Please select linking channel 2. Switch of the light; after 10 seconds, switch on again. 3. Press the linking button once within 3 seconds. 4. Link is done when the light blink 3 times slowly. Note: If the light doesn't blink slowly, Linking is failed. 1. Please check if the light is compatible with the remote. 2. Check if the light has been linked; The linked light cannot be linked again. 3. Please follow above steps to link again. Unlinking instruction: 1. PleaLseeasernleicntgth.e..Plinlekiangsechparnensels any button 2. Switch of the light; aoftnerr1e0mseocteonds, switch on again. 3. Press the unlinking button once within 3 seconds. 4. Unlink is done when the light blink 10 times quickly. Note: If the light doesn'tCbalinnkcqeul ickly, Unlinking is failed. 1. Please check if the light is compatible with the remote. 2. Check if the light has been linked; The unlinked light cannot be unlinked again. 3. Please follow above steps to unlink again. Zone1 Select zones Zone2 Zone3 Zone4 Zone5 Zone6 Zone7 Zone8 Learn Link Unlink Restore gateway ID: Short press gateway "SET" five times; restore successfully after devices indicating lamp blink 3 times. Zone selection: Click the "Zone" on the left bottom into the Zone selection. Note: Please select the linked Zone, otherwise it cannot control the lamps. Setting DMX512 address: Click "Set DMX" on the top right corner; Set DMX512 address for gateway on the pop-up window. Mobile 10:18 433 Gateway 95% Set DMX Mobile 10:18 433 Gateway 95% Set DMX Set DMX512 Address Current address001 Please input number from 1~512 Cancel OK Gateway need to occupy 5 address to control lamp's red,green,blue,warm white and coor white accordingly. i.e: Set the gateway DMX512 address to 008 Occupied address 008 009 010 011 012 Controlled colors Red Green Blue Cold white Warm White Note: You must link the lamps to the gateway to control the lamps(Linking instruction see details for Miboxer APP Link/Unlink interface). Attention 1. The input voltage is DC5V/500mA, Please do not connect the power supply over DC5V, otherwise, the device will be broken easily. 2. Non-professional user cannot dismantle the divice directly, otherwise, the device will be broken easily. 3. The working temperature is -20~60^; Do not install the device to direct sunlight, moist and other high temperature area. 4. Please do not install the device around the mental area and high magnetic field, otherwise, it will badly affect the control distance. Zone1 White Light Timer Link / Unlink Zone1 White Light Timer Link / Unlink Made in China MiBoxer APP User Instruction 1 APP Downloading For IOS System: Pls search "MiBoxer" on APP store. (Above IOS9.0) For Android System: search "MiBoxer" on Google Play (Above Android 5.0) or Scan below QR-code to download APP. Scan QR Code to Install APP 2 Register MiBoxer Account Open APP and click Register button;Complete the register and log in. Mobile 10:18 95% Subordinate New Brand United Kingdom +44 Mobile number / Email address Password I agree Service Agreement and Privacy Policy Log in Register Authentication code login Forgot Password 3 Add Device 1. Click the right top "+" on the device list. 2. Please select the device type you will add, then complete the adding according to the hint of APP. 3. Back to device list after adding successfully, then pull down refresh in list to get the device status. Mobile 10:18 95% Device List %FWJDF (SPVQ %JTDPWFSZ 4 Modify device name or delete device Slide device list to left, click " Edit " to modify device name; click " Delete " to delete device. Note: If the device was shared to others, then the device will also be deleted on your friends' device list. Mobile 10:18 Device List Remote Controller Gateway WiFi Box Controller ON 95% ON ON ON ON Edit Delete %FWJDF (SPVQ %JTDPWFSZ 5 APP Control Click the device or group that you want to dim on device list and group list into Dimming Interface. Click speed+ under dynamic mode. Click speed- under dynamic mode. Mobile 10:18 95% Controller 6 Third Party Voice Control instructions Search "Mi-Light Smart" on third-party platform APP and set up. Click left top " " icon on the home page; Then click " Voice Control " to check detailed instructions. Mobile 10:18 95% Anson *********@****.com Log Out Setting Shared Device Voice Control Version V1.0.1 7 Sharing Device Share the device to friends, Let your friends can control this device. 1. Click the left top " " icon on the home page. 2. Click " Shared Device " to My sharing, then click"Add sharing" (Note: the receiving sharing device cannot be shared again). 3. Click " sharing. Jack jack@milight.com " to edit sharing, slide to left to delete Mobile 10:18 95% My sharing Sent sharing Received sharing You share the device to below users Jack jack@milight.com Miranda miranda@milight.com Pierson pierson@milgith.com Delete White Light Timer Add sharing Scan QR code to watch online video for WiFi pairingAdobe PDF library 15.00 Adobe Illustrator CC 23.0 (Windows)