User Manual for HDWR Global models including: AC700LF Rfid Card Access Keypad and Password, AC700LF, Rfid Card Access Keypad and Password, Access Keypad and Password, Keypad and Password
User Manual RFID card access keypad and password SecureEntry-AC700LF Table of contents Specifications: ............................................................................................................................................................... 3 Set contents: ................................................................................................................................................................... 4 Features: ............................................................................................................................................................................ 4 Introduction..................................................................................................................................................................... 5 Installation........................................................................................................................................................................ 5 Connection ...................................................................................................................................................................... 6 Drawing Connection Diagram ...........................................................................................................................7 Programming .................................................................................................................................................................. 7 Entering the Preset Mode............................................................................................................ 7 Set the master code..................................................................................................................... 7 Setting the Wiegand output format ....................................................................................... 8 Setting the PIN format.................................................................................................................. 8 Setting the keyboard backlight ................................................................................................ 8 Factory reset ................................................................................................................................... 9 Function Table............................................................................................................................................................... 9 PIN Output Format .....................................................................................................................................................10 2 Specifications: · Warranty: 1 year · Material: ABS · Verification Type: RFID Card, Password · Device type: RFID card access keypad and password · Number of buttons: 12 · Keyboard and keys: silicone keys · Reading distance: 3 ~8 cm · Cards read: EM · Operating frequency: 125 kHz · Interface: Wiegand 26 · Access control: yes · Working Voltage: DC 12~18V · Standby Current: 35mA · Ingress Protection: IP66 · Operating temperature: -40°C ~ 60°C · Operating Humidity: 0%~95% · Product dimensions: 12.2 x 5 x 2.1 cm · Package dimensions: 13 x 7.5 x 5.5 cm · Product weight: 155 g · Weight with packaging: 210 g 3 Set contents: · RFID access keypad with cables · Screws and mounting pins · Special Key · Manual Features: · The robust design and IP66 rating make the units resistant to water streaks, so they can be mounted at the entrance of a building · The access keypad has a built-in RFID card reader, which, when combined with an electronic lock, allows you to open the door not only after entering the password, but also after reading the card · The device supports DC 12 ~18V and 125 kHz frequency · Compact and lightweight 4 Introduction The device is an access keypad with a Wiegand output and an integrated proximity reader, and thanks to its water resistance, it can be installed both indoors and in harsh environmental conditions. Features: · Resistant to water ingress, IP66 compliant · Programmable Wiegand output: 26~37 bits · Programmable keyboard transmission: 4-bit, 8-bit, or virtual card number format · External LED and buzzer control Installation · Drill 2 holes (A, C) on the wall for screws and one hole (B) for the cable. · Drive the rubber pins into the holes (A, C). · Attach the back cover to the wall using 2 screws. · Pull the cable through the cable hole (B). · Attach the appliance to the back cover. 5 Connection Colour Red Black Green White Brown Yellow Function Power + GND D0 D1 LED Buzzer Comments +DC (9~18V DC) Ground Date 0 Date 1 Green LED Control Buzzer control 6 Drawing Connection Diagram Programming Change the configuration settings according to the app (optional). Multiple configuration settings can be changed at the same time: enter programming mode, change the desired settings, and then exit programming mode. Entering the Preset Mode Press * for 5 seconds until you hear a beep, enter the master code # Set the master code A master code of 4-6 digits is used to prevent unauthorized access to the system. To connect to the keyboard reader, the manager will need the master code (factory default code 1234). 7 We recommend that you update immediately and register a new master code. Programming step Entering Programming Mode Master Code Update Exit Programming Mode Key Combination * (Master Code) # 0 (New Master Code) # Repeat New Master Code) # (Master Code Is 4-6 Digits) * Setting the Wiegand output format Programming step Entering Programming Mode Format settings Exit Programming Mode Key Combination * (Master Code) # 1 (26-37) # (Factory default: 26 bits for EM 125 kHz) * Setting the PIN format Programming step Entering Programming Mode Format settings Exit Programming Mode Key Combination * (Master Code) # 2 0# (Virtual Card Number) 2 4# (4 bits, default)2 8# (8 bits) * Setting the keyboard backlight Programming step Entering Programming Mode Key Combination * (Master Code) # 8 Automatic shutdown On all the time Disabled Exit Programming Mode 3 0# (The backlight will turn off after 20s inactivity) 3 1# (default) 3 2 # * Factory reset Turn off the power, press "*" and hold, then turn on the power, release the * key until you hear 3 beeps. Function Table Card reading External LED control External buzzer control Wiegand Data Output The LED will illuminate green and the buzzer will beep. meanwhile, the reader sends a Wiegand signal When the input voltage for the LED is low, the LED will turn green When the input voltage of the buzzer is low, the buzzer will make a sound Wiegand 26~37 bits available for the reader. Factory default settings: 26 bits. 9 PIN Output Format The default keyboard transmission format is 4 bits, 8 bits, or a virtual card number format, which can be customized. · 4 bits The reader will transmit PIN data each time a key is pressed: 1 (0001), 2 (0010), 3 (0011) 4 (0100), 5 (0101), 6 (0110) 7 (0111), 8 (1000), 9 (1001) * (1010), 0 (0000), # (1011) · 8 bits The reader will transmit PIN data each time a key is pressed: 1 (1110 0001), 2 (1101 0010), 3 (1100 0011) 4 (1011 0100), 5 (1010 0101), 6 (1001 0110) 7 (1000 0111), 8 (0111 1000), 9 (0110 1001) * (0101 1010), 0 (1111 0000), # (0100 1011) · Virtual card number The reader will transmit the PIN data when the last key (#) after the PIN is pressed. Example: PIN: 999999. Press 999999# and then the output format will be 0000999999. 10Microsoft Word 2019