A401 Portable Thermal Printer Instruction Manual
Getting Started
This manual provides instructions for the A401 Portable Thermal Printer.
Power On and Use Method
Power On: Press and hold the operation button for 3 seconds to turn on the printer.
Paper Loading Method
- Simultaneously pull the lid opening buttons on both sides of the machine forward to open it.
- Open the paper bin and place the paper according to the signs, ensuring the correct side faces up.
Printing Method
Single paper / folding paper placement:
- Open the buttons on the left and right sides of the machine.
- Align the paper with the arrow mark and insert it about 5cm deep into the machine's rear feed slot. The print side should face up.
- Lift the upper cover, insert the paper to the edge of the output tray (approximately 2cm), and then close the upper unit. Ensure both sides of the top cover are properly seated. A clicking sound indicates it's closed correctly.
Application Installation and Printing
Connecting to a Windows Computer for Printing:
- Connect the computer and printer using a USB cable.
- Ensure the printer is powered on.
- Download and install the printer driver from www.cnfujun.com/d/54.
- Add the printer on your computer and establish a communication connection to enable printing.
Mobile Apps: Use the provided Android and iOS apps for printing.
Product Information and Status
Product Introduction
Operation Button:
- Single click: Feeds paper to the next black mark position.
- Double click: Prints a self-test page.
- Click more than 4 times: Initiates paper calibration.
Paper Plate Usage: The paper plate can be adjusted for A5, A4, and Letter paper sizes. For A5 paper, position the plate as shown. For Letter paper, remove the plate.
Product Information
- Product Name: Portable Thermal Printer
- Printing Type: Thermal print
- Input Voltage: DC 5V/2A
- Battery: 2600mAh Li-battery
- Paper Width: A4/A5
- Interface: Type-C
- Net Weight: 868g
- Product Size: 276.6*104.6*74mm
Printer Status Indicators
Indicator Light & Buzzer Description:
| Status | Indicator Light (Blue/Red) | Buzzer |
|---|---|---|
| Power On | Long light | Off |
| Power off and charge | Off | Ring flashes |
| Bluetooth connection successful | Long light | "Beep beep" |
| Out of paper | Off | 500ms frequency flashing "Beep beep beep" |
| Open cover | Off | 1s frequency flashing "Beep beep beep" |
| Black mark error | Off | 750ms frequency flashing "Beep beep beep" |
| Over temperature (high temperature) | Off | 1.5s frequency flashing "Beep beep beep" |
| Low battery | Off | 300ms frequency flashing "Beep beep beep" |
Packing List
- Printer*1 pc
- USB*1 pc
- User Manual*1 pc
Product Warranty Card
Product Information:
- Product name: [Product Name]
- Product model: [Product Model]
- Product number: [Product Number]
- Purchase date: [Purchase Date]
- Contact information: [Contact Information]
- Contact number: [Contact Number]
- Company address: [Company Address]
The company provides warranty service from the date of purchase. The following situations are not covered by the free warranty:
- Unauthorized dismantling or repair.
- Damaged barcode or fragile sticker, or altered/incomplete warranty card.
- Failures caused by not operating the equipment according to instructions.
- Man-made damage from water ingress or dropping.
- Failures or damage caused by force majeure.
- Issues outside the warranty period.
Certifications: CE, Q.C. PASSED
FCC Compliance Information
FCC Warning Statement: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
There is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.