Digilent â Start Smart, Build Brilliant.
Owner's Manual for DIGILENT models including: PmodCON3 R-C Servo Connectors, PmodCON3, R-C Servo Connectors, Servo Connectors, Connectors
Digilent, Inc.
File Info : application/pdf, 2 Pages, 497.24KB
DocumentDocumentPmodCON3TM Reference Manual Revised April 15, 2016 This manual applies to the PmodCON3 rev. C 1300 Henley Court Pullman, WA 99163 509.334.6306 www.digilentinc.com Overview The Digilent PmodCON3 (Revision C) can be used to easily interface with up to four small servo motors that deliver anywhere from 50 to 300 ounce/inches of torque, such as those used in radio controlled airplanes or cars, as well as some mechatronics projects. The PmodCON3. Features include: Four standard 3-wire servo motor connectors Easily interface with Digilent system boards Flexible power delivery to servos Small PCB size for flexible designs 1.0 in × 0.8 in (2.5 cm × 2.0 cm) 6-pin Pmod port with GPIO interface Follows Digilent Pmod Interface Specification Type 1 Example code available in resource center 1 Functional Description The PmodCON3 allows any Digilent system board to easily interface with a standard 3-wire servo motor consisting of a signal, positive power supply, and ground power supply wires. The power supply can be sourced either from the system board or an external power source via screw terminals by selecting the appropriate setting on the jumper block. 2 Interfacing with the Pmod The PmodCON3 communicates with the host board via one of the four GPIO pins (the first four pins on the 1×6 header). As mentioned in the Functional Description, it is also possible to select how to power an attached servo motor by setting the shorting block in the appropriate jumper configuration. DOC#: 502-082 Downloaded from Arrow.com. Copyright Digilent, Inc. All rights reserved. Other product and company names mentioned may be trademarks of their respective owners. Page 1 of 2 PmodCON3TM Reference Manual Header J1 Pin Number 1 2 3 4 5 6 Description Servo P1 Servo P2 Servo P3 Servo P4 Ground VCC Jumper JP1 Jumper Setting VCC VE Description The voltage source for the servos comes from VCC and Ground The voltage source for the servos come from the + and - screw terminals Table 1. Connector J1- Pin Descriptions as labeled on the Pmod. Standard servo motors use a potentiometer to adjust the angle at which their central shaft rotates to. In order to adjust the rotation angle, the motor generally needs to receive a "high" voltage pulse that ranges from 1 millisecond to 2 milliseconds, with 1.5 milliseconds as the "neutral" value. These values typically correspond to 0 degrees, 180 degrees, and 90 degrees, respectively, although depending on the manufacturer of the servo motor, these angles may vary. A signal that is either too narrow or too wide for a servo will cause the servo to try to go beyond its rotational range and can damage the servo. Always check the manufacturer's instructions for a servo's rotational range. 1.5 ms Pulse Width Servo Position Set by Pulse Width 2.0 ms Pulse Width 1.0 ms Pulse Width Pulse Period Figure 1. Servo control diagram. Because the pulse length is relatively long, any of the IO pins on a Digilent system board are capable of driving a servo motor. However, in order to have the servo motor maintain its given angle, a refresh pulse of the same (or new) angle will need to be provided to the servo motor periodically (20 milliseconds is a safe value). When using the Servo library available from Digilent, the refresh pulse and the pulse width are automatically taken care of, allowing the user to simply give the desired angle for the servo motor to rotate to. 3 Physical Dimensions The pins on the pin header are spaced 100 mil apart. The PCB is 1.0 inches long on the sides parallel to the pins on the pin header and 0.8 inches long on the sides perpendicular to the pin header. Copyright Digilent, Inc. All rights reserved. Other product and company names mentioned may be trademarks of their respective owners. Downloaded from Arrow.com. Page 2 of 2