KOHLER Kitchen and Bathroom
Installation Guide for KOHLER models including: K-8304-K Rite-Temp Valve Body and Cartridge Kit Complete, K-8304-K, Rite-Temp Valve Body and Cartridge Kit Complete, Temp Valve Body and Cartridge Kit Complete, Body and Cartridge Kit Complete, Cartridge Kit Complete, Kit Complete
Brass 1/2-in Mnpt Pressure Relief Valve 885612369192
File Info : application/pdf, 2 Pages, 148.56KB
DocumentDocumentRite-Temp® Valve Body & Cartridge Kit Complete K-8304-K Features · Includes valve body, pressure balance cartridge, rough-in guide, and mudguard. · 1/2" Universal NPT and direct sweat inlets and outlets. · 5 gpm (18.9 l/min) maximum flow rate at 45 psi. · Single lever design cycles from off through cold to hot. · Antiscald protection. · One-piece cartridge design simplifies installation and maintenance. · Adjustable high-temperature limit stop to control maximum water temperature. · Requires valve trim to complete installation (sold separately). · Pressure-balancing diaphragm technology maintains outlet temperature within +/-3°F during water pressure fluctuations. Material · Forged dezincification-resistant brass body provides long term reliability and resistance to aggressive water conditions. Installation · Designed for use in standard, back-to-back and thin wall installations. · Valve body features integral mounting locations and symmetrical valve inlets to simplify installation. · Cartridge is reversible for installations where hot and cold supplies are reversed. · Rough-in guide designed for both standard and thin wall installations. · Installed valve rough-in can be flushed and pressure-tested to 150 psi max (air or water) without cartridge by using test cap (sold separately). Codes/Standards ASME A112.18.1/CSA B125.1 ASSE 1016/ASME A112.1016/CSA B125.16 KOHLER® Faucet Lifetime Limited Warranty See website for detailed warranty information. Optional Products/Accessories K-10350 Deep rough-in kit K-10351 Test cap for K-8300 Series valve bodies 1-800-4KOHLER (1-800-456-4537) Kohler Co. reserves the right to make revisions without notice to product specifications. For the most current Specification Sheet, go to www.kohler.com. 2-1-2022 04:27 - US/CA/MX Max Finished Wall Min Finished Wall Outlet Port 1/2"-14 NPT and 5/8" ID for 1/2" Nominal Copper Tubing Rite-Temp® Valve Body & Cartridge Kit Complete K-8304-K 4-5/8" (117 mm) Cutout for finished walls less than 3/4" (19 mm) Ø 4-1/2" (114 mm) Ø 4" (102 mm) 1-15/16" (49 mm) Cut Line 1-15/16" (49 mm) Outlet Port 9/16" (14 mm) 2-3/16" (56 mm) 2-3/4" (70 mm) 2-15/16" (75 mm) 3-1/2" (89 mm) Inlet Port 1/2"-14 NPT and 5/8" ID for 1/2" Nominal Copper Tubing 7/8" (22 mm) Cutout for finished walls greater than 3/4" (19 mm) Ø 5" (127 mm) Cut Line Technical Information All product dimensions are nominal. Shower Valve: Pressure: Maximum (Static) Pressure: Minimum (Operating) Pressure: Valve body: Machined-brass 45 psi (3.1 bar) 125 psi (8.6 bar) 20 psi (1.4 bar) Notes Install this product according to the installation guide. Avoid cross-flow conditions. Do not install shutoff device on either valve outlet. Cap the shower outlet if deck-mount spout, diverter, or handshower is connected to the spout outlet. Install straight pipe or tube drop of 7" (178 mm) to 18" (457 mm) with single elbow between the valve and wall-mount spout. For finished walls greater than 3/4" (19 mm) and less than 1-1/2" (38 mm), install support(s) 2" (51 mm) from the stud face. For finished walls greater than 1-1/2" (38 mm), install support(s) 3" (76 mm) from the face of the finished wall. 1-800-4KOHLER (1-800-456-4537) Kohler Co. reserves the right to make revisions without notice to product specifications. For the most current Specification Sheet, go to www.kohler.com. 2-1-2022 04:27 - US/CA/MX