JODAN CAM 720 Outdoor Dual-Lens WIFI Camera

Camera Introduction

Power on reset: Please insert the camera adapter, press and hold the reset button for 5 seconds to reset the camera until you hear "Di-". Continue to wait for "Di-" 2 times, and the camera will complete the self-test.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.

Information to User: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Important: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

CAM720 APP Usage

Download the CAM720 APP from the App Store or Google Play, or by scanning the QR code provided.

App Features:

• Return to the device list
• Share the device
• More function settings
• Switch image effects
• Switch into Full-screen image
• Turn on screen record function
• Screenshot to save the image
• Turn on voice intercom
• Turn on the microphone

Device List Functions:

• Back to the device list
• Modify the device name
• Share equipment
• SD card setup
• Detection alarm settings
• Buy cloud storage
• Image Flip: upside down
• Choose a call mode
• PTZ rotation control
• Message List
• Enable/Disable Auto tracking
• SD card Playback
• Choose night vision mode
• Turn on cloud play
• Set the time zone
• Add more cameras
• Switch WiFi network
• Camera information
• Start Live video
• Subscribe Cloud storage
• More functions setup
• Delete the camera
• Camera version number
• Transfer the camera to another account
• Screen recording feature
• Screenshot to save the image
• Close the video window
• Turn off full-screen images

Note: Tap the small screen 3 times in a row to switch the lens screen to each other.

Sign up & Login

Register an account: Click "Register" > enter your email address, set your APP passcode, check the verification code, and wait for the verification to be completed. You will then be jumped directly to the APP list.

Note: If you don't want to register an account, you cannot use remote features. You can use standalone mode to view the camera, which only supports local view.

WiFi Connection

1. In the APP: click "+" > select "WiFi connection".
2. Check "Hear the device announce didi"; Click "Next".
3. Follow the prompts shown in the app (please connect WiFi to JAA-**** and go back to the Cam720 APP).
4. Enter the correct password for the WiFi connection of your phone and click "Next".
5. When the device is connected, please wait patiently until the camera is online, then click the video to view.

Important: Keep the camera and router at a distance of two meters.

Wired Connection

Plug the power supply and Ethernet cable to the router. Please plug the adapter for the camera and connect the camera with the Ethernet cable to the router.

Reset the camera: Long-press the reset button for about 5-8s until you hear a prompt. Select wired connection to connect it.

NOTE: Please confirm the cellphone is connected to the same WiFi as the router that the camera is connected to. If the camera has a Network port, it supports wired/WiFi connection; otherwise, please select WiFi connection to connect.

Playback

Turn on the playback function. Two recording methods are available: SD card record (8-256G) and Cloud Record. SD card record supports 3 record modes: 24/7 continuous, motion-triggered, scheduled record.

Bracket Mounting

Installation procedure:

1. Keep bracket A in the same direction as the fixed lens, then bring the camera and bracket A together, and then turn bracket A to hold them both in place.
2. Put the other end of bracket A together with the slot of bracket B, and then just push it down.
3. Attach the bracket B to the wall and make a mark on the hole to punch holes. Use a 6mm drill bit to get the holes, then stuff the rubber stopper into the hole.
4. Select a suitable location and install expansion screws on the wall. For example, if it's a wooden wall, expansion screws are not required.
5. Align the bracket with the hole position and tighten the screws.

Share

Share your camera with your friends and families.

1. Your friend should have an account on the cam720 APP.
2. Scan the QR code of the account to share it.
3. In the main account, enter the Email of the friend's APP account.
4. Freely set the permission on this shared account.

Detection Alarm Settings

1. Zoned area vigilance detection: The red part represents the planned warning area.
2. Warning information push: Alarm information is pushed to the mobile phone in time through the APP background.
3. Sound alarm: Warns suspicious characters to leave as soon as possible, and supports custom voice.

How to Use Correctly

1. This product is suitable for indoor scenes; it is not waterproof. Please avoid outdoor installation.
2. It should be installed in a ventilated environment as much as possible to avoid unstable factors caused by long-term closed high-temperature replacement.
3. The camera and the router should be controlled within 10 meters of the partition wall, and in an open environment, within 20 meters.
4. When using at night, do not place items in front of the camera lens and do not face the wall, glass window, mirror, etc., so as not to block the reflection of infrared rays and affect the image quality.
5. The installation area should be away from high-power equipment to avoid signal interference and affect the use experience.

Troubleshooting

Q1: What should I do if WiFi configuration failed?

A1: Make sure GPS Location service is on and "Allow" is selected for all app permissions. Check that the WiFi password is entered correctly (no more than 31 digits, and mind the case). After all steps above are completed, check router settings, such as: "blacklist", "firewall", "Device Internet restrictions", etc.

Q2: How to do if the camera is always offline?

A2: Please check the connection of the camera adapter and socket, or replace the power supply. Check the WiFi signal strength; move the camera closer to the router.

Q3: How could multiple users view at the same time?

A3: Please use the share function to add other users.

After-sale Service & Tech Support

Need some help?

Email: technicalreply@qacctv.com, market@qacctv.com

For user guides, FAQs, warranty & more, scan the QR code below to access YouTube. Select the right operation video for your camera according to the APP and Model of the camera, or message the seller to get the operation video directly.