Thermal Printer, Thermal Receipt Printer, Mini Thermal Printer - SPRT
User Manual for SPRT models including: SP-POS5813 Wholesale Super Light Weight Printer, SP-POS5813, Wholesale Super Light Weight Printer, Super Light Weight Printer, Light Weight Printer, Weight Printer, Printer
Wholesale Super Light Weight Printer with Competitve Price SP-POS5813 Manufacturer and Supplier | Spirit
Wholesale Super Light Weight Printer with Competitive Price SP-POS5814 58mm Printer Manufacturer and Supplier | Spirit
File Info : application/pdf, 15 Pages, 476.86KB
DocumentDocumentSPRT® POS Thermal Receipt Printer SP-POS5813/POS5814 User's Manual (Ver 1.00) Beijing Spirit Technology Development Co.,Ltd. www.sprt-printer.com 1 Content INTRODUCTION ....................................................................................................................................................3 CHAPTER 1 FEATURE AND PERFORMANCE .................................................................................................. 3 1.1 PRINT PERFORMANCE .................................................................................................................................... 3 1.2 PRINT PAPER ..................................................................................................................................................4 1.3 PRINT FONT ................................................................................................................................................... 4 1.4 INTERFACE ..................................................................................................................................................... 4 1.5 PRINT CONTROL COMMANDS .......................................................................................................................... 4 1.6 POWER SUPPLY ..............................................................................................................................................5 1.7 OPERATION ENVIRONMENT ............................................................................................................................. 5 1.8 OUTLINE DIMENSION & WEIGHT ......................................................................................................................5 CHAPTER 2 OPERATION INSTRUCTIONS ........................................................................................................5 2.1 PRINTER APPEARANCE ................................................................................................................................... 5 2.2 PAPER INSTALLATION ...................................................................................................................................... 7 2.3 INTERFACE ..................................................................................................................................................... 8 2.3.1 Communication Interface ...................................................................................................................... 8 2.3.2 Cash Drawer Interface .........................................................................................................................10 2.4 BUZZER, BUTTONS AND INDICATORS ............................................................................................................. 11 2.5 SELF-TEST ................................................................................................................................................... 12 2.6 ENTER PROGRAM UPGRADE MODEL .............................................................................................................. 13 2.7 HEXADECIMAL PRINTING ............................................................................................................................... 13 2.8 RESTORE FACTORY SETTINGS ....................................................................................................................... 13 CHAPTER 3: PRINTER DRIVER INSTALLATION ............................................................................................ 13 APPENDIX 1: PERFORMANCE SPECIFICATIONS ......................................................................................... 14 2 Introduction SP-POS5813/POS5814 printer is a new type line thermal printer, it features in fast speed print, low print noise, high reliability, perfect print quality and ribbon needless, avoiding the vexation of regular maintenance. SP-POS5813/POS5814 printer: small in outline dimension, simple operation, and extensive application, especially suitable for commercial cash register, PC-POS, bank POS and all kinds of receipts print. Warning This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Chapter 1 Feature and Performance 1.1 Print Performance Print method: direct thermal Print paper width: 57.5±0.5mm Print density: 8 dots/mm,384 dots/line Print speed: max 90mm/s Reliability (1) Print head life: 50km Using condition: Print 12 × 24 ASCII characters, print 50 lines each time, intermittent print repeatedly No more than 25% of each dot line can be printed simultaneously, and the same dot of each character line can be printed vertically no more than 11 times. Use specified thermal paper (2) Cutter life: 1500,000 cuts Valid print width: 48mm 3 1.2 Print Paper Paper Type: Thermal Paper 79.5±0.5mm x80mmmax Paper Thickness: 0.06mm0.08mm Paper Loading Method: Easy loading Paper Cutting Method: Manual 1.3 Print Font ANK Character Set 12×24 dots,1.5W×3.00Hmm. GB GB2312-80(Chinese): 24×24 dots,3.00W×3.00Hmm. 1.4 Interface Communication Interface: USB Interface(Type B, Female) Parallel(DB25, Male) Serial(RS232, P/S2) Bluetooth(BTDM, BTMM) Ethernet Interface: Normal Ethernet interface. Cash Drawer Control: DC12V, 1A, 6-pin RJ-11 socket. 1.5 Print Control Commands Character print commands: support double-width, double height print of ANK characters, user-defined 4 characters and Chinese characters, the character line spacing is adjustable. Graphics print commands: support the print of bit-map graphics and download bit-map graphics with different density GS barcode print commands: support UPC-A, UPC-E, EAN-13EAN-8, CODE39, ITF25, CODEBAR, CODE93, CODE128 1.6 Power Supply DC8.5V, 2A 1.7 Operation Environment Operation temperature: 050; Relative humidity: 1080 Storage temperature: -2060; Relative humidity: 1090 1.8 Outline Dimension & Weight Dimension: 120(L)mm×100(W) mm×95 (H)mm Weight: 280g(without paper roll) Chapter 2 Operation Instructions 2.1 Printer Appearance Printer appearance As shown in Figure 2-1-1, Figure 2-1-2. 5 Rubber Roller Paper Cover Main Case Feed Button Power Indicator Error Indicator Power Socket Figure 2-1-1 6 Ethernet USB Cash drawer Power Parallel Power Serial Cash drawer Power Figure 2-1-2 2.2 Paper Installation USB Cash drawer Power SP-POS5813/POS5814 printer adopts 58mm width thermal paper. The thermal paper installation steps are as follows: 1. When there is no paper in the print head, please do not press the feed button to avoid affecting the life of the print head. As shown in Figure 2-1-1, hold the paper cover and pull it upward to open the door and change paper. 2. Do not manually pull the paper forward or stuff the paper backward after the paper cover is closed. 7 2.3 Interface 2.3.1 Communication Interface 1. Standard Type-B USB. Figure 2-4 USB Interface PIN NO Function Note 1 V Bus The power supply is +5V. 2 Data - The data is negative. 3 Data + The data is positive. 4 GND Power ground 2. Standard DB25 parallel port connector, male plug. pins Definition Description Pins Definition Description 1 STROBE Active low signal for 14 Auto Automatically insert data transmission Feed a line break for every carriage return in the printer 2 D1 The first bit of data. 15 nError Low-level indication indicates the presence of an error state. 3 D2 The second bit of 16 data. Prime 4 D3 The third bit of data. 17 Select Input 5 D4 The forth bit of data. 18 GND 8 6 D5 The fifth bit of data. 19 7 D6 The sixth bit of data. 20 GND 8 D7 The seventh bit of 21 data. GND 9 D8 The eighth bit of data. 22 GND 10 nACK Response signal 23 GND 11 BUSY Busy signal, active 24 GND high 12 Paper Paper out signal, 25 GND End active high 13 Select High-level message indicates that the printer is online. 3. RS232 interface Insert the dedicated DB9-P/S2 cable and follow the instructions on the self-test page to configure the serial port. Pin Definition Description 1 RS323_RX Serial Data Receiving 2 RS323_TX Serial Data Transmission 3 RTS Request to send low effective. 4 CTS Cancel sending low effective. 5 GND 6 GND 9 4. BluetoothBTDMBTMM Turn on the Bluetooth on the terminal device, search for the corresponding device based on the Bluetooth information on the self-check page, and input the password to connect to the device. Note: The "POWER" light of the device will blink within the first 30 seconds after powering on; once Bluetooth is successfully connected after 30 seconds, this light will stay on. Bluetooth information can be set through the settings software. 5. Ethernet Insert the Ethernet cable, enter the settings mode, refer to section 2.4.3, item 2, and select "Enable DHCP with 5-second delay confirmation". The device will automatically obtain an IP address and save it, which will be used as the device's static IP address thereafter. Use the settings software to configure the corresponding IP address. Note: When the router's network segment changes, or when there is an IP address conflict within the local area network, the settings need to be reconfigured. 2.3.2 Cash Drawer Interface The cash drawer interface of the SP-POS5813 printer adopts an RJ-11, 6-pin socket, as shown in Figure 2-3-1. Fig. 231 Cash drawer interface The pin definitions are as follows in Table 2-3-2: PIN NO. Signal Direction 1 Chassis Ground --- 2 Cash drawer driver signal output 3 On/off signal of cash drawer input 4 +12VDC Output 5 N.C --- 6 Signal ground --- Tabel 232 Definition of Cash Drawer Interface Pin 10 2.3.3 Power Connection SP-POS5813/POS5814 printers are externally powered by a dedicated DC 8.5V/2A power supply. 2.4 Buzzer, Buttons and Indicators 2.4.1 Power ON/OFF The power switch controls the power on/off status. When the device is turned off, pressing the button will turn it on. Pressing the power button again will turn it off. power 2.4.2 Feed Button as the paper feed key, can be used for function settings and paper feed. 1.Under normal operation, pressing the key on the printer will feed the paper, and releasing the key will stop the paper feed. 2.Function selection 2.4.3 combination button 1. While the printer is out of paper and powered off, press and hold down the without releasing it. Then, briefly press the mode. and wait for the prompt sound "Beep...beep...". Release the to enter upgrade 2. With paper loaded and the printer powered off, press and hold the button without releasing it. Then, briefly press the button again and wait for the prompt sound "Beep...beep...beep...". Release the button to enter function setting mode. Press the button briefly once to print the corresponding functions prompt: "Print self-test, hexadecimal mode, restore factory settings, dynamic IP acquisition (UE model)". The confirmation will be automatic after a delay of 5 seconds. 11 2.4.4 Indicator lights and buzzer. Green: Indicates the power switch status, stays on when the device is turned on. Note: Within the first 30 seconds of turning on, this light will flash; after 30 seconds of turning on, it will stay on constantly once the Bluetooth connection is successful. The red light and buzzer indicate error statuses. When the printer is working normally, the red "STATUS" indicator light will be off. If this light begins flashing, it indicates an abnormal warning status. The buzzer can be set to enable or disable error alerts through parameter settings. When enabled, it will be used to indicate the type of error status, which is the same as the "STATUS" indicator light. When the error indicator light is blinking and the buzzer is sounding (when enabled), it indicates that the printer has encountered an error. The specific type of error can be indicated by the different patterns of blinking. The error status indicators are shown in the following table. Indicator light status Buzzer Status Description off off Normal Flash once, off about 1 second. Beep once, pause for about 1 second. Out of paper, will resume normal operation once paper is available. Flash twice, off for about 1 second. Beep twice, pause for about 1 second. The head is overheating, please wait for the engine temperature to decrease. It will automatically resume once the temperature is normal. Flash three times, off for about 1 second. Beep three times, pause for about 1 second. The head heating plate is damaged and cannot be restored. It needs to be repaired. Table 24 2.5 Self-Test Self-testing can check whether the printer is working properly. In self-testing, the software version number, interface form, character configuration information, etc. are sequentially printed. If the self-test can correctly print out the self-test sample, it indicates that other parts of the printer are working properly except for the communication interface with the host. Otherwise, maintenance is required. 12 Self-testing method: With paper loaded and the printer turned off, press and hold the key, release within 3 seconds, and the printer will print out the self-test list. 2.6 Enter program upgrade model Refer to section 2.4.3, step 1, to upgrade by selecting the appropriate interface and program file using the "UpdateFirmware" software. Note: Parallel port models cannot be upgraded using a "USB to Parallel Port cable." 2.7 Hexadecimal Printing In reference to 2.4.3, Item 2, the three lines of prompts printed in hexadecimal mode are as follows: Hexadecimal Dump To terminate hexadecimal dump, Press FEED button three times. Under this mode, all inputs will be printed as hexadecimal numbers. Press the key to feed paper for each line, repeat this process for a total of 3 times. Then, print "*** Completed ***" and exit the hexadecimal print mode. 2.8 Restore factory settings Reference 2.4.3, item 2, only restore the printing configuration information, do not restore the Bluetooth and network configuration information. Chapter 3: Printer Driver Installation To install the SP-POS5813/POS5814 series printer driver, please download it from our official website at www.sprinter.com.cn. Follow these specific steps: 1. Go to the homepage and navigate to the Download Center. 2. Select "Driver Programs" and then choose "POS Printer Series." 3. Download the driver program named SP-DRV211. During the installation process, make sure to select the printer model as "58 Thermal Series." For further instructions on how to install and use the driver program, please refer to the installation guide provided. 13 Appendix 1: Performance Specifications Specifications Printing Method Thermal Line Print Performance Specifications: Resolution Printing Speed Effective Printing Width 8 dots/mm (203dpi)/ 384 dots/line 90 mm/s 48mm Paper Width 57 .5mm±0.5mm Custom printing character Support Graphics Printing Support for printing graphics with different dot densities and downloading bitmap images for printing. Print Support Features Chinese English GB2312-Level 3 Character Library: 24x24 dot matrix ASCII: 9x17 dot matrix, 12x24 dot matrix Barcode UPC-AUPC-EEAN-13EAN-8CODE39 CODE93 CODABARITF25 CODE128 Interface USB, Serial, Parallel, Bluetooth, Ethernet, cash drawer Support function Paper shortage alarm, overheat protection, buzzer Cash drawer control DC12V, 1A, 6-pin RJ-11 socket Power Supply Direct current supply power DC8.5V2A Paper Paper Type Paper Thickness Normal thermal paper 58×Ø 60mm 0.06mm0.08mm 14 Physical properties Paper loading Easy paper loading Paper Cutting Method Manual Dimension 120mm×100mm×95mm (L×W×H) Weight 275 g no paper roll Work environment 0-50°C (working environment temperature) / temperature/humidity 10-80% (relative humidity) Environmental factors Save environment temperature/humidity 2060Save environment temperature /1090% (relative humidity) Life span / Reliability TPH 50km STATEMENT This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 15