4G IoT Wireless Gateway (GW0300B) User Manual

Specification

Input Voltage: 9V~36VDC

Rated current: 500mA/12V

Cellular

• LTE FDD: B2, B4, B5, B12, B13, B14, B66, B71
• WCDMA: B2, B4, B5
• Wi-Fi: 801.11b/g/n; BLE4.2

Environment Requirements

• Operating temperature: -10°C ~ 55°C
• Battery Charging Temperature: 0 ~ 45°C
• Battery Discharging Temperature: -20 ~ 60°C
• Battery Storage Temperature: -20 ~ 45°C (Storage period ≤ 3 months)
  -10 ~ 25°C (3 months < Storage period ≤ 6 months)
• Relative Humidity: 95%, non-condensing

Dimension

179mm x 121mm x 48mm

Interface Definition

PWR Interface

CAN Interface

RS422 Interface

Filed Installation

• Install the 4G antenna and Wi-Fi/BLE antenna on the gateway. The gateway is attached to the side of the control cabinet by four strong magnets or hung on the gateway bracket. Antennas are attached to the top of the control cabinet.
• When installed by four strong magnets, the installation height of the gateway is less than 2m.
• The dimension of the gateway bracket is as follows: The bracket is 6.00mm thick. The main body is 68.15mm wide and 77.30mm high. Mounting holes are spaced at 56.00mm horizontally and 52.00mm vertically. A small tab extends 1.50mm.
• The bracket is fixed on the wall with 4pcs M3*18 countersunk head tapping screws and 4pcs M4*20 plastic expansion screw columns.
• Follow the Otis ONE system wiring diagram for wiring operations.

Commissioning Operation Instructions

• Download the "Smart SVT" APP. [Smart SVT App Icon]
• Log in: The machinist needs to log in with their account.

Diagram description: A diagram shows the GATEWAY connected to a CONTROLLER. The GATEWAY has connections labeled CAN (pins 1, 2, 3) and PWR (pins 1, 2). The CONTROLLER has connections labeled CAN (pins 1, 2, 7, 9) and PWR (pins 1, 2). The connections are shown with wires running between them.

Commissioning Steps

• Enter the elevator unit ID in the unit search bar.
• Find and select the target elevator from the search results, then click the "Add Gateway" button.
• Select commission interface type (SVT or CAN).

Commission Gateway Details

• Scan the Gateway bar code on the front label or manually enter the Serial Number.
• Manually enter the elevator manufacturing date and GPS coordinates.
• Click the "Add Gateway" button.

Gateway Commission Status and Connection

The gateway commission status is displayed as "Successful" or "Failed".

View elevator and gateway details: gateway status, gateway and elevator connection status

• Gateway Configuration Status: If the gateway battery icon is green and the "DEV" LED is always on, configuration is successful. If the icon is gray, configuration failed and requires reconfiguration.
• Communication Interface: If the communication interface icon is displayed as SVT, it means the gateway is connected to the controller via RS422.
• Elevator Connection Status: If the lift link status icon is green and the "LINK" LED flashes, the gateway and elevator are connected successfully. If the icon is red, the connection has failed.

Warnings and Compliance

FCC Compliance

§ 15.19 Labelling requirements: This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

§ 15.21 Information to user: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

§ 15.105 Information to the user: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning for Mobile device: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Canada, ISED Notice

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Canada, ISED avis: L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1) L'appareil ne doit pas produire de brouillage; 2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Certified Module Information

This device contains certified module FCC ID: XMR201909EC25AFX and IC No: 10224A-2019EC25AFX.