User Manual for BiDaE models including: LB60004G, 2AZL6-LB60004G, 2AZL6LB60004G, LB60004G Beacon, Beacon
BiDaE Technology, Incorporated LB60004G LBeacon 2AZL6-LB60004G 2AZL6LB60004G lb60004g
BiDaE LB60004G User Manual BiDaE Technology, Incorporated Address:1F., No. 5, Ln. 96, Sec. 1, Da'an Rd., Da'an Dist., Taipei City 106069 , Taiwan (R.O.C.) Email:sales@bidae.tech http://www.bidae.tech Regulatory Compliance Statements FCC Warning Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to Connect the equipment into an outlet on a circuit different from that to -Consult the dealer or an experienced radio/TV technician for help. 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure requirements, avoid direct contact to the transmitting antenna during transmitting. 3. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment. FCC Label Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. European Conformity Statement BiDaE Technology declares that the product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive. CE Mark Warning RoHS Statement This device conforms to RoHS (Restriction Of Hazardous Substances) European Union regulations that set maximum concentration limits on hazardous materials used in electrical and electronic equipment. Contents I. Product Information ............................................................................. 1 II. Network Setup........................................................................................ 2 II.1 - Connection with LB60004G ............................................................... 2 II.2 - Set up.................................................................................................... 2 II.3 - Connection to Wi-Fi ........................................................................... 3 II.4 - Setting Static IP ................................................................................... 4 II.5 - Setting Access Point ........................................................................... 5 I. Product Information Exterior RESET Power Ethernet port Description RESET When LB60004G works abnormally, press Reset button to restart. power 5 V,2.5A for full power delivery to USB devices Ethernet Ethernet ports for connecting the LB60004G to the local port computers 1 II. Network Setup II.1 - Connection with LB60004G Wireless connected by LBeacon default AP ssid:BiDaE_AP Or connected by Ethernet cable II.2 - Set up Setup Using Browser Enter IP(default IP:192.168.2.1) in address bar and login Username:root, No password 2 II. Network Setup II.3 - Connection to Wi-Fi Go to Web Setting >Network> Wireless>Scan>Join Network>Enter"passphrase">save>submit>save>Save & Apply 3 II. Network Setup II.4 - Setting Static IP Go to Web Setting >Network> Wireless>WWAN>Edit Select "Static address">enter the"IPv4">save>Save & Apply 4 II. Network Setup II.5 - Setting Access Point .Setting Wireless Access Point Go to Web Setting >Network>wireless> Edit>change "ssid">change "key">save>Save & Apply 5 II. Network Setup Setting LAN static IP Go to Web Setting >Network> Interfaces LAN>Edit> enter the "IPv4">save>Save & Apply 6 II. Network Setup Turn off LBeacon AP Go to Web Setting >Network> Wireless>Disable> Save & Apply 7Acrobat Distiller 9.3.3 (Windows)