Installation Guide for imupos models including: S-200, S-200AL, E-200, S-200 All In One POS System, All In One POS System, POS System, System
20 hours ago — Specifications in the user manual are subject to change without prior notice. S-200. S-200AL. E-200. Model. Intel Celeron Quad-core. Processor J6412 2.0GHz/ ...
pirms 1 dienas — Specifications in the user manual are subject to change without prior notice. S-200. S-200AL. E-200. Model. Intel Celeron Quad-core. Processor J6412 2.0GHz/ ...
Rev. 1.2EN(202310) S-200 l S-200AL l E-200 All-in-One POS System Safety Precautions Be sure to read the Safety Precautions before using the POS system. ··Before connecting, make sure the operating voltage is AC100 ~ 240V. Otherwise, you may damage the system. ··Do not install the system in an extremely hot or cold place. ··Avoid exposing the product in direct sunlight or in an enclosed space for a long period of time. ··Be careful not to place the system near other high-frequency electromagnetic devices; there is a strong possibility it will lead to a system malfunction or system error. ··Do not place heavy objects on the system. ··Please do not allow external substances to be contaminated inside the system. ··Do not change the motherboard's battery by yourself. It can damage the system. ··Before disassembling the system, disconnect all power and cables. ··Do not remove or repair the system by yourself. We highly recommend an engineer's assistance or an experienced technician to open the system, especially the LCD and touch panels which could be easily broken. ··An electrical outlet is needed near the device and it should be easily accessible. ··Risk of explosion if battery is replaced by an incorrect type. Replace only with the same type of batteries recommended by the manufacturer. ··This device complies with the EMC (Electromagnetic Compatibility) Regulations, for business purposes. Distributors and users are advised of this matter. ··Do not use excessive force when using or pressing the touch panel. Do not use objects with sharp edges on the touch panel. ··Please exchange the equipment if you mistakenly sold or purchased this product. ··Cleaning and Maintenance is relevantly necessary for POS terminal to be operated well. POS Terminal Security Guideline Operating System Security System-provided and managed by the operating system's default security settings must be configured. Touch Screen Security Guideline Please take special care with the touch panel as it is vulnerable to scratches. ··Do not use excessive force when using or pressing the touch panel. Do not use objects with sharp edges on the touch panel. ··Be careful not to spill any liquid on the screen. ··Turn off the power switch and unplug all cables before cleaning the screen and/or the system. ··Use a soft, clean, dry cloth for cleaning the system, and do not use chemicals or detergents. 2 POS TERMINAL Configuration S-200 l S-200AL l E-200 All-in-One POS System Stand Rear Cover 3 I/O Cover Disassembly with Upper Lower upper I/O and lower I/O ports. Upper Lower 4 System Connection and Power on Please install the system referring to video clip thru QR code written in manual. Power Cord Connection Please connect power addptor DC jack and power cord by turns after all option items are connected. I/O cover will be disassembled by pushing the "PUSH" part of both sides. Please disassemble it by pushing up stand rear case. Please insert power adaptor cable by turning it into DC 12V port at upper I/O ports. Please connect power cord after assembling it in a reverse way of disassemble. Power on Please turn the power on after installing all optional items. The power cord connects 220V (110V) power after fastening the DC plug to the mainbody of POS. Power Supply Indicator is located on the lower right side of the monitor. When power is connected, the LED will light up. Each LED lamp will indicate the operation status. HDD LED: Operation mode (GREEN) LAN LED: LAN Connection (RED) Power LED: Power Connection (BLUE) Power Switch 5 Installation Options 2nd Display Please turn it on after connecting all the option items. Please disassemble I/O cover and stand rear cover. Please strongly tighten the plastic bolt at the rear side of stand after inserting the round-edge part of 2nd display cradle into the hole between POS system and stand. Please insert cable into display port out of I/O ports. Please assemble I/O cover and stand rear cover. 6 Card Reader Please insert Card Reader at the groove ininmmoonnitiotor rtotoththeeaarrrorowwddirierecctitoionn after disassembling I/O cover and set it well by pushing to the arrow ddirierecctitoionn. . Please close I/O cover after inserting the cable into COM6/USB port of I/O ports. Please turn the power off after finishing SSD replacement. Please push the monitor up and pull out the SSD in Disk Tray by holding handle of Disk Tray. Please be cautious on direction when it is assembled. When SSD is replaced, please separate SSD by pushing it up through the hole of Tray. 7 Model S-200 S-200AL E-200 (Fanless)12th Generation Intel® CoreTM Intel® Celeron® Quad-core i3(1215U),i5(1235U),i7(1255U)Processors Processor J6412 2.0GHz/2.6GHz Intel® Alder Lake SoC / AMI UEFI Intel® Elkhart Lake SoC / AMI 2.5" SATA III SSD 128GB (SSD 256/512GB, optional) 4GB SO-DIMM DDR4 2133MHz x 2 (Max 32GB, optional) Intel HD Graphics 620 / Intel Iris Plus Graphics 640 DDR4 3200MHz x 1 (Max 32GB, optional) Corei3-1215U-IntelUHD Graphicsfor12thGenIntelProcessors Core i5-1235U / Core i7-1255U - Intel IrisXe Graphics DDR4 2666MHz~3200MHz x 1 (Max 32GB, optional) Intel® UHD Graphics for 10th Gen Intel® Processors 3 (# of Displays Supported) - up to 3 monitors (optional) Windows 10 IoT Enterprise 64bit, Windows 11 64bit 15" LED Backlight (1024 x 768 Resolution) * E*-SEe-rSieesrieiss1is5.165".F6H" FDH(1D9(21092x01x08108R0esolution / 16:196):A9v)aAilvaabilaeble PCAP 10 Point Multi-touch 2 x USB 2.0 (Rear Top x 2), 4 x USB 3.0(Rear Bottom x 4), 1 x USB 2.0 (RJ11) Speaker(optional) 1W x 1 3W x 1 · LCLDCTDypTeyp: 9e:.79".7o"r o1r51"5L"CLDC(DUS(UBSPBoPrtoxrt1x) 1) · ToTuochucMhoMnoitnoirt:o9r:.79".7o"r o1r51"5L"CLDCwDitwhitChaCpapciaticvietivTeoTuochuc(hUS(UBSPBoPrtoxrt1x) 1- )b-ybsyinsginlegcleabcaleb(nleo(npoopwoewr e&rU&SUBScBabcaleb)le) · Standard Monitor: supported standard DP, HDMI, DVI, VGA monitor by change monitor cable · Standard and Powered DP MST Hub: supported standard or powered(customized) DP MST Hub. FSTN LCD Type(20 columns x 2 lines) 362 X 237 X 352 (mm) 5.0 Kg DC 12V/5A (AC 100V~240V, 60W) DC 12V/7A (AC 100V~240V, 84W) DC 12V/5A (AC 100V~240V, 60W) OpOepraetriantginTgeTmepm:p0:~04~040/ S/toSrtaograegTeeTmepm:p-2: 0-2~06~060/ H/uHmuimdiitdyit:y21:02~09~09%0H%nHonno-cno-cnodnednesninsging This user manual is provided for informational purposes and cannot be reproduced or distributed without consent under the Copyright Act. Specifications in the user manual are subject to change without prior notice. 8Adobe InDesign 18.0 (Windows) GPL Ghostscript 9.53.3