Installation Guide for OSRAM models including: ST GEN 30W, ST GEN 60W, ST GEN 80W, ST GEN 120W, ST GEN 150W, ST GEN 180W, ST GEN 200W, ST GEN 240W, LUXVANCE Streetlight General Edition, LUXVANCE, LUXVANCE Streetlight, Streetlight, Streetlight General Edition
21 ore fa — • Please read instruction carefully before assembling and installation. • Please keep instruction as reference in the future. Installation Manual. Shorting cap ...
• Please read instruction carefully before assembling and installation. • Please keep instruction as reference in the future. Installation Manual. Shorting cap ...
File Info : application/pdf, 5 Pages, 1.37MB
DocumentDocumentLUXVANCE® Streetlight General Edition Installation Manual · Please read instruction carefully before assembling and installation · Please keep instruction as reference in the future Shorting cap included. PE cell sold seperately as accessory LUXVANCE® Streetlight General Edition H LUXVANCE® Street W L H Wattage Installation Weight Voltage IP IK ta Light General (mm) (mm) (mm) (W) height (kg) (v) Edition (m) LUXVANCE ST GEN 175 467 88 30W LUXVANCE ST GEN 60W 30W 60W LUXVANCE ST GEN 221 564 88 80W 80W LUXVANCE ST GEN 120W 120W LUXVANCE ST GEN 241 642 88 150W 150W LUXVANCE ST GEN 180W 180W LUXVANCE ST GEN 276 740 88 200W 200W LUXVANCE ST GEN 240W 240W 6-9 1.56 AC120- 66 08 40°C 277V 50Hz/ 60Hz 8-11 2.57 9-12 3.05 3.77 1. To change orientation of spigot, loosen or remove bolts used to secure the shaft. 2 LUXVANCE® Streetlight General Edition 2. Adjust the angle of the lamp head and secure it by tightening the screws. 2a 2b 3.Ensure that the power is switched OFF. Connect the the luminaire to mains using an IP rated terminal. 4. Secure the lamp by tightening the pole screws to prevent it from becoming unstable. 4a 4b 3 LUXVANCE® Streetlight General Edition 5. Switch power ON and check that the luminaire is operational. 6. Note: Shorting cap must be attached to fitting to ensure fixture is operational. Shorting cap can be disgarded if PE Cell is utilised. 4 WARNING 1. Ensure that any installation and maintenance be performed by a qualified electrician and the luminaire is wired in accordance with the local wiring and relevant Australia standards. 2. Ensure that the power supply is off before starting installation and maintenance. Do not switch on until the installation or maintenance is completed. 3. The light source of this luminaire is non-user alternative light source, the light source contained in the luminaire shall only be replaced by the manufacturer of his service agent or a similar qualified person. 4. Make sure the products are grounded. 5. Power supply system should be equipped with SPD (Surge Protection Device) accordance with electrical regulations. 6. The products are suitable for outdoor use. 7. For luminaires with dimmable LED drivers. reinforce insulation was provided between LV supply and output/dimming circuit. 8. For NEMA version, make sure to meet the waterproof requirement after installing the short cap or NEMA controller. 9. The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than 3m is not expected. 10. Glass cover was constituted with a glass having a high impact shock resistance. Service Contact: Haneco Lighting Australia Pty Ltd 262 Marion Road, Netley, South Australia 5037 Haneco.com.au 1300 001 533 OSRAM is a trademark of OSRAM GmbH. TRAXON is a licensee of product trademark OSRAM for a fixed list of General Lighting product. Haneco Lighting Australia is a Traxon distributor of OSRAM products in Australia, New Zealand and Pacific Islands. OSRAM OFFICIAL LICENSEE Traxon Technology Ltd. 213 Wireless Centre, 3 Science Park East Avenue, Science Park, Shatin, New Territories, Hong Kong Phone: +852 2943 3488 www.traxon-ecue.com