User Manual for sewoo models including: SLK-TS100 Receipt Printer, SLK-TS100, Receipt Printer, Printer
13 To use this command, the printer must be connected as follows: [Command Code] ASCII: GS ( 0 ? Decimal: 29 40 107 48 129 Hex: 1D 28 6B 30 81
SLK-TS100. Direct thermal 220mm/s Resolution Interface. 203dpi USB Serial Ethernet Paper width. 79.5±0.5mm Printable area. 72mm(adjustable by commands) Maximum paper diameter Paper thickness. Φ80 mm 0.06~0.08mm Column capacity Line space. 576 dots/line 3.75mm(Changeable by commands) Commands Drivers Bar code.
File Info : application/pdf, 8 Pages, 1.91MB
DocumentDocumentAroot Co., Ltd. Rev. Apr 2023 Do not use or store in locations subject to high temperature, humidity or pollution levels. Connect the power adapter into a properly grounded outlet. Do not share the same plug socket with electrical motors or other equipment which may cause the power supply voltage fluctuations. Avoid water or conductive materials like metal, from getting inside the printer. If this happens, immediately unplug the AC power cord. Do not attempt to print without paper. Unplug power supply from the printer if it will be unused for an extended period. Only use power adapter supplied with printer. Only use approved accessories. Never disassemble or modify the printer for repair or reconstruction. Be sure to use the original specified power source. High quality paper is recommended for best print quality and to extend the life of the printer. Be sure to turn the power switch to OFF before plugging and unplugging the power supply. Do not use this printer above 5,000 meters (16,000ft) above-sea-level in tropical climates or in high humidity conditions. Fast printing speed of up to 220mm/s. Large paper roll capacity: up to 120mm diameter. High speed text and graphic printing: Excellent printing quality and reliable performance even at maximum speed. Supports printer status monitoring function offering remote user visibility at any time. Printer "announces" when the receipt is being printed resulting in orders being expedited and processed more quickly. High speed download and logo printing mode. Supports Windows, plus Linux operating systems. Supports black mark detection for form printing. 256k Bytes NV Flash RAM for store and print of logo's. Standard with serial + USB + Ethernet interfaces. Supports network printing; perfect for kitchen applications. Mechanism life can reach to 100km and Auto cutter life with 100 million cuts. Supports 2D barcodes: QR Code & PDF417. Supports multiple international fonts (as options) . Chinese GB18030 code page as an option; Simplified/traditional Chinese are convertible. Built-in web page allows for setup of printer directly through IE port. 58MM/80MM paper roll can be optional. Specifications Model Printing method SLK-TS100 Direct thermal Printing speed 220mm/s Resolution 203dpi Interface USB+Serial+Ethernet Paper width 79.5±0.5mm Printable area 72mm(adjustable by commands) Maximum paper diameter 80 mm Paper thickness 0.06~0.08mm Column capacity 576 dots/line Line space Commands 3.75mm(Changeable by commands) Compatible with ESC/POS Drivers Win 9X/Win 2000~2003/Win XP/Win 7~8/ Win 10/Linux Bar code UPC-A, UPC-E, JAN13(EAN13), JAN8(EAN8), CODE39, ITF, Code page CODABAR, CODE93, CODE128, QR CODE, PDF417 PC437(Std.Europe)a(Katakana)\n\aPC850(Multilingual) a PC860(Portugal)aPC863(Canadian)aPC865(Nordic)a(West Europe)a (Greek)a(Hebrew)a(East Europe)a(Iran) a(WPC1252)a PC866(Cyrillic#2)aPC852(Latin2)a(PC858) a(IranII)a(Latvian)a (Arabic)a(PT1511251) Cutter Partial Cutter life Print head life 1.5 million cuts 100 KM Mechanism life 100 KM Input buffer 64 Kbytes NV Flash 256 Kbytes Black mark Support Network monitoring Support Adaptor input voltage AC110V/220V, 50~60Hz Power supply DC 24V/2.5A Printer input voltage DC 24V/2.5A Cash drawer control DC 24V/1A Working environment Temperature: 0~45°C , humidity: 10~80RH% Storage environment Temperature: -10~60°C, humidity: 10~90RH% Dimension 185×142×136 mm (D×W×H) Gross weight 1.025 kg CONNECTING THE PRINTER A. Connect AC power cord to power, DC power cord to printer. B. Connect printer to computer or device. C. Connect cash drawer. A Power cord Power adaptor B C PAPER ROLL INSTALLATION An 80mm wide thermal paper roll is recommended for 80mm series printers. Follow the steps below to install the roll paper: 1. Open the top cover by pressing the COVER OPEN button. 2.Insert the roll paper per the following illustrations: 3.Pull out a small amount of paper, and close the cover 4.Printer will automatically feed the paper and cut 03 04 FUNCTION OVERVIEW: Get to know your printer - POWER LED: Indicates when printer is powered on - ERROR LED: ON or BLINKING indicates error condition (see Troubleshooting Chart below) - PAPER LED: ON or BLINKING indicates error condition (see Troubleshooting Chart below) - FEED button: Press to feed paper. Hold to feed paper continuously - COVER OPEN button: Press to open the top cover, to insert paper roll DRIVER INSTALLATION Two methods to print receipts: 1) Printing directly through the port 2) Using the printer driver. 1) Printing directly through the port a. There is no need to install the printer driver. Just select the correct port (i.e., USB, LAN, Serial, Parallel) in the application software. 2) Install driver under WINDOWS OS (Steps as below): 1. Double click POS Printer Driver Setup V7.17 driver. 2. Select: "I accept the agreement" 3. Create a shortcut on the desktop: 4. Setup Completed: 05 06 5.Select the correct interface port: 7. Click "Yes" to configure the port. 6. Select the proper printer series and click "Install Now" 8. Choose the detected USB001, click apply, shown as below: 07 08 9. Select the "General" tab and then "Print Test Page": (5) How to resolve cutter paper jams - Method 1 : Cycle the power to the unit. - Method 2 : A. Turn the printer off. B. Open the top cover. TROUBLESHOOTING GUIDE (1) Self-Test instructions: Make sure the printer is connected to power and turned off. While pressing the FEED button, turn on the power. Release the FEED button after both the ERROR and PAPER LEDs blink twice. The printer will automatically print out a self-test which includes the printer's firmware version, status and configuration. (2) Config Mode You can set serial communication speed,print density and melody type by using feed button. You can select an item by pressing feed button as many times as the number of the item you want to set. (3) How to enter hexadecimal mode Make sure the printer is connected to power and turned off. While pressing the FEED button, turn on the power and keep it pressed, waiting for both the ERROR and PAPER LEDs to blink twice simultaneously, and then for the ERROR LED to stay on. At this point, release the FEED button and the printer will enter hexadecimal mode. Pressing the FEED button twice will cause the printer to print "Hexadecimal Dump" on the first line of the paper indicating that it is now in hexadecimal mode. To exit Hexadecimal Dump mode and return back into normal print mode, press the FEED button three times, or cycle the power. (4) 09 Resetting to Factory (default) Settings Make sure the printer is connected to power and turned off. While pressing the FEED button, turn on the power, waiting for both the ERROR and PAPER LEDs to blink twice simultaneously, then for the ERROR LED to turn on, and then for both the ERROR and PAPER LEDs to blink twice more. Release the FEED button when the buzzer alarms, confirming that the unit has been reset to factory default settings. C. Turn the white gear on the cutter, and take jammed paper out. D. Only when the cutter is turned back to the initial (home) position, can the cover be opened. 10 LED TROUBLESHOOTING CHART LED INDICATOR POWER ERROR PAPER OPERATING CONDITION OFF ON OFF OFF OFF OFF Power off Normal mode Ready to print ON OFF BLINKING Out of paper ON ON ON ON BLINKING ON ON BLINKING OFF ON BLINKING OFF Top Cover open Out of paper Paper Inserted Top Cover Open Cutter Jam Thermal Head Overheated REMEDY 1) Plug in AC adapter 2) Turn on power None required 1) Open Top Cover 2) Insert paper roll 3) Close Top Cover 1) Insert paper roll 2) Close Top Cover 1) Close Top Cover 1) Cycle the power on the unit 1) Power down printer 2) Open Top Cover 3) Wait 10 min to cool down CLEANING THE THERMAL PRINTHEAD and ROLLER Clean the thermal printhead on a routine basis, or if one of the below conditions occurs: (1) Blurred printing. (2) "White" vertical streaks on printed receipt. (3) Noise during paper movement. Follow these steps to clean the printhead and roller: (1) Power off the printer and open the roll paper cover. Remove the roll paper, if any. (2) If the thermal printhead is hot, wait for it to cool before cleaning. (3) Clean the elements of the thermal printhead with a printhead cleaning pen or cleaning swipe made specifically for thermal printhead, or with a cotton swab moistened with an alcohol (isopropyl alcohol) solvent. (4) Clean the rubber roller with the solvent (5) Wait till the solvent completely evaporates or dries before inserting the paper roll and closing the top cover. Print self-test page and repeat if necessary as it may take a few cleaning cycles to remove all debris from printhead. If problem persists, contact the party you had purchased the product from, to request service. QR Code function 1. QR Code: Set unit size [Command Code] ASCII: GS (0 g n Decimal: 29 40 107 48 103 n 11 Hex: 1D 28 6B 30 67 n Function Description: Set the unit size of QR Code into "n" Parameter Range: 1 n 16 Default n = 3 Note: n = Unit width in dots = Unit height in dots The ESC @ command setup failed when printer is powered off and reset. 2. QR Code: Set up error correction level [Command Code] ASCII: GS (0 i n Decimal: 29 40 107 48 105 n Hex: 1D 28 6B 30 69 n Function Description: Set up QR Code error correcting grade, The value for "n" is as below: n Level Correct proportion (%) 48 Grade L 7 49 Grade M 15 50 Grade Q 25 51 Grade H 30 Parameter Range: 48 n 51 Default: n = 48 Note: QR Code uses RS error correction algorithm and the command setting will reset when printer is reset or powered off. QR Code: Data transmission to code cache [Command Code] ASCII: GS (0 nL nH d1...dk Decimal: 29 40 107 48 103 nL nH d1...dk Hex: 1D 28 6B 30 80 nL nH d1...dk Function Description: Setting QR Code data transmission to code cache Parameter Range: 4 (nL + nH×256) 2710 32 d 255 Default: None Note: After receiving, the data will be kept in the cache until next reset K byte d1...dk be regarded as coded data d1....dk must only contain data in the following table: Characters Numeric Alpha, Numeric and special characters Chinese Character 8 bits data Including the below character in the table "0"~"9" "0"~"9", "A"~"Z", SP, $, %, *, +, -, b, a,: GB18030-2000, Shift-JIS, JISX0208 standard 00H~FFH The ESC @ command setup failed when printer is powered off and reset. 12 QR Code: Printing QR Code of code cache [Command Code] ASCII: GS ( 0 ? Decimal: 29 40 107 48 129 Hex: 1D 28 6B 30 81 Function Description: Printing the encoded data in the code cache Parameter Range: None Default: None Note: If the QR code size is outside printing area, the QR code will not be printed If the code cache data is empty, the QR code will not be printed USB port and Virtual Com Port exchange command set [Command code] ASCII: US ESC ............................ Decimal: 31 27 31 184 19 20 N Hex: 1F 1B 1F B8 13 14 N Description: Select Real USB port or Virtual Com Port Range: N=0 USB; N=1 Virtual Com Port. To use this command, the printer must be connected as follows: 13Adobe PDF library 16.04 Adobe Illustrator 26.1 (Windows)