New Drawing | Magma
One Stop Systems
User Manual for OSS models including: OSS-KIT-EXP-6002 Host Server to Expansion System Kit, OSS-KIT-EXP-6002, Host Server to Expansion System Kit, Host Server, Expansion System Kit, System Kit
PCIe x4 Host to CPCIe Expansion Kit (6002) - One Stop Systems
File Info : application/pdf, 15 Pages, 1.10MB
DocumentDocumentOSS-KIT-EXP-6002 Host Server to Expansion System Kit User Manual SKU: OSS-KIT-EXP-6002 www.onestopsystems.com One Stop Systems Table of Contents 1 Overview .......................................................................................................................................................................... 3 1.1 Description .................................................................................................................................................................................................... 3 1.2 Features .................................................................................................................................................................................................... 4 1.1.1 Adapter Cards................................................................................................................................................................................. 4 1.1.2 x4 Link Cable................................................................................................................................................................................... 4 1.3 Specifications ............................................................................................................................................................................................ 5 1.3.1 Host Adapter .................................................................................................................................................................................. 5 1.3.2 Expansion Link Board ..................................................................................................................................................................... 5 1.3.3 PCIe x4 Cable .................................................................................................................................................................................. 6 2 Component Identification ................................................................................................................................................. 7 2.1 Host cable adapter card ............................................................................................................................................................................ 7 2.2 Expansion Link Board ................................................................................................................................................................................ 7 3 Installation Instructions .................................................................................................................................................... 8 3.1 Installing the Adapter Kit............................................................................................................................................................................... 8 3.2 Expansion link board ..................................................................................................................................................................................... 8 3.3 Removing PCIe Cable..................................................................................................................................................................................... 8 3.4 Operation ...................................................................................................................................................................................................... 8 4 Technical Information ....................................................................................................................................................... 9 4.1 Signal Adjustment ......................................................................................................................................................................................... 9 4.2 Pin Assignments ............................................................................................................................................................................................ 9 4.3 Pin-out for the PCIe x4 Card Edge Connector on the "Host Cable Adapter" ............................................................................................... 10 4.4 PCI Express x4 Connector PIN Assignment .................................................................................................................................................. 11 4.5 Pin-out for the PCIe x4 Cable ...................................................................................................................................................................... 11 4.6 Signal Descriptions ...................................................................................................................................................................................... 12 4.7 Connector Pin-outs for the PCIe x4 Cable Connector .................................................................................................................................. 12 4.8 PCI Express x4 Connector PIN Assignment .................................................................................................................................................. 13 5 Contacting Technical Support ..........................................................................................................................................14 6 Returning Merchandise to One Stop Systems ..................................................................................................................14 OSS-KIT-EXP-6002| 2 One Stop Systems 1 Overview 1.1 Description The PCIe x4 expansion kit is used to extend the PCI express bus from a host server to an external expansion chassis. The host adapter card inserts into a PCIe slot of the server. It then cables to a downstream expansion link board (ELB). The ELB acts as a downstream cable link board and the primary fan-out switch to support multiple configurations of PCI express expansion slots. The host adapter installs into a PCIe x4, x8 or x16 slot on the host motherboard. It then cables to the expansion link board and installs in the SHB or system slot of a CPCIe backplane. OSS-KIT-EXP-6002| 3 One Stop Systems 1.2 Features 1.1.1 Adapter Cards The Host adapter card inserts into any PCI Express x4, x8, 16 slot on the host motherboard. The Target adapter card fits into SHN slot of PICMG 1.3 backplane.. Support half-height bracket. The Host and Target cable adapter cards require no software / drivers 1.1.2 x4 Link Cable Available in 1m, 2m, 3m, 5m, 7m lengths. PCI-SIG Express Cable Specification Compliant. Includes x4 PCIe lane and side-band signals for: o Power ON o Reset o PCIe clock o Cable Present o Wake Positive latching mechanism per PCI-SIG specification Support 10 Gbps full-duplex transfer rates. OSS-KIT-EXP-6002| 4 One Stop Systems 1.3 Specifications 1.3.1 Host Adapter PCIe x4 Host Cable Adapter Card (SKU : OSS-PCIe-HIB25-X4-H) Form Factor Dimension (H x L) Front Panel Connectors Front Panel Indicators Red-drivers Temperature Range Relative Humidity Shock Vibration Power Consumption Agency Compliance Redriver PCIe x4 add-in card 2.7" x 3.1" (68 x 78mm) One PCIe x4 cable connectors Power ON / Cable Present LED Pericom P12EQX5804 0° to 50°C (32° to 122°F) 10 to 90% non-condensing 30g Acceleration peak (11 ms pulse) 5-17 Hz 0.5" double amplitude displacement; 7-2000Hz, 1.5g acceleration 3.75W typical, 3.3@1.3A UL60950, FCC Class B, CE safety and emissions, ROHS Pericom P12EQX5804 1.3.2 Expansion Link Board PCIe x4/x8 Gen2 Expansion Link Board (SKU : OSS-SHB-G2-x8-x4) Form Factor Slot Type Dimension (H x L) Switch Upstream Interface Downstream Interface Front Panel Connectors Front Panel Indicators Power Consumption PCIMG EXP.system slot compliant. Single Slot System slot for the expansion chassis 3.937 x 6.299 in (100 x 160 mm), 1 slot wide PLX PEX8733 32 lane switch x4 PCI Express over cable PCI-SIG PCI Express Cable Rev 2.0 Compliant 16 lanes of PCI Express on the backplane connectors. The lanes form two or four links to the backplane through the XP2 and XP3 connectors per the PICMG EXP.0 specification. The following link modes are automatically selected by the backplane as follows: · Two link mode: 2 x8 links (per backplane capabilities) · Four link mode: Four x4 PCIe links 1 PCIe x4 Cable (Molex : 75586-0010) 4 backplane link-active indicators (green) 2 or 4 link mode + cable link (green) 10W typical +12V @ .5, 3.3V @ 1.25A, 5Vaux @ 2.5mA Temperature Range Relative Humidity Storage Temperature Shock Vibration 0° to 50°C (32° to 122°F) 10 to 90% non-condensing -40° to 85°C (-40°-185°F) 30g acceleration peak (11ms pulse) 5-17 Hz 0.5" double amplitude displacement; 7-2000Hz, 1.5g acceleration Agency Compliance UL60950, FCC Class B, CE safety and emissions, ROHS OSS-KIT-EXP-6002| 5 1.3.3 PCIe x4 Cable PCIe x4 Cable (SKU : OSS-PCIe-CBL-x4.1M) 1 meter long cable Cable Length Circuits loaded Gender Lock to Mating Part Material-Metal Pitch-Mating Interface Single Ended Water proof / Dust proof Wire Insulator Diameter Wire Size AWG Wire / Cable Type Electrical Current Shielded Voltage-Maximum 1m, 2m, 3m, 5m, 7m 38 Male-to-Male Yes Zinc Alloy 0.80mm (0.31) No Yes N/A 28 Round 1A Max per contact Yes 30V DC One Stop Systems OSS-KIT-EXP-6002| 6 One Stop Systems 2 Component Identification 2.1 Host cable adapter card The PCIe x4 expansion kit contains two cable adapter boards, the host cable adapter and the target cable adapter. The host adapter inserts into the host computer's PCIe x4, x8 or x16 slot. Cable LED indicators are the same for both Host and Target configurations. 2.2 Expansion Link Board The Expansion Link Board (ELB) OSS-CPCIe3-3U/6U-ELB-x4 is a downstream link board that installs into a CPCIe chassis. The ELB fits into the system slot of a CPCIe backplane. The ELB is the downstream link board and the primary fan-out switch to support multiple configurations of CPCI or CPCIe expansion slots. OSS-KIT-EXP-6002| 7 One Stop Systems 3 Installation Instructions 3.1 Installing the Adapter Kit 1. Insert the host cable adapter into an appropriate PCIe slot of the host computer. For example, a PCIe x4 host board can be inserted into a PCIe x16, x8, or x4 slot. It will still operate at x4 speeds. Secure the cable adapter card 3.2 Expansion link board 1. Insert the expansion link board into the SHB slot on the chosen backplane. 2. Connect the x4 PCIe cable to both cables adapter cards. Press or pull the green TAB while slowly inserting the cable, then release it to lock the cable. See photos below. OR 3. Test by pulling back on the connector. 3.3 Removing PCIe Cable 1. To remove the cable, press or pull the green tab and slowly pull the cable out. 3.4 Operation 1. Plug in expansion system and turn the power supply on. 2. Power up host computer. 3. The expansion system will power up. OSS-KIT-EXP-6002| 8 One Stop Systems 4 Technical Information The transmit and receive signals on the OSS-HIB-25x4 are driven and conditioned by Pericom redriver chips. Adjustments can be made to equalization, de-emphasis and output swing. These controls are factory set by the use of zero Ohm resistors. In the following tables, a 0 indicates that a zero Ohm resistor has been installed and a 1 indicates no resistor. In rare cases, mostly where nonOSS equipment is used with the HIB-25x4, these adjustments may need to be changed. The following tables are made available for this purpose. It is highly recommended to contact OSS customer support before making changes to these settings. Having the customer solder to the board should void the warranty. 4.1 Signal Adjustment Equalizer Selection S EL_ 2I A: 0 I 0 0 SEL_ 1I A: 0 I 0 0 SEL_ O[ A: 01 0 1 @1.25 GHZ 0 .5dB 0 .6dB 0 1 0 1.0dB 0 1 1 1.9dB 1 0 0 2.BdB 1 0 1 3.6dB 1 1 0 5.0dB 1 1 1 7.?dB @2 .5G HZ 1. 2dB 1.5dB 2.6dB 4 .3dB 5.BdB 7.1dB 9.0dB 12 .3dB Ed ge Defa u lt Cab le Defa ult De-emphasis Adjustment 0 2_ [A:D ] 0 0 0 0 1 1 1 1 D1_(A: D] DO_JA;D] De-emphasis 0 0 OdB 0 1 -2.Sd B 1 0 -3.Sd B 1 1 -4 .SdB 0 0 -5.Sd B 0 1 -6.SdB 1 0 -7.SdB 1 1 -8.SdB SW=ON Defau lt SW=OFF Defaul Output Swing Control S_ 1[A:D] 0 0 1 1 S_O[A: D] 0 1 0 1 Swi ng (Diff. VPP) 1V 05V 0.7V 0.9V Cable Defau lt Edge Default 4.2 Pin Assignments Host and Target card connectors (x4 Card Edge Connector) The pins are numbered as shown with side A on the top of the centerline on the solder side of the board and side B on the bottom of the centerline on the component side of the board. The PCIe interface pins PETpx, PETnx, PERpx, and PERnx are named with the following convention: "PE" stands for PCIe high speed, "T" for Transmitter, "R" for Receiver, "p" for positive (+), and "n" for negative (-). Note that adjacent differential pairs are separated by two ground pins to manage the connector crosstalk. OSS-KIT-EXP-6002| 9 One Stop Systems 4.3 Pin-out for the PCIe x4 Card Edge Connector on the "Host Cable Adapter" Side B Pin # Name 1 N/C 2 N/C 3 N/C 4 GND 5 NC 6 N/C 7 GND 8 +3.3V 9 N/C 10 3.3Vaux 11 N/C 12 RSVD 13 GND 14 PETp0 15 PETn0 16 GND 17 PRSNT2# 18 GND 19 PETp1 20 PETn1 21 GND 22 GND 23 PETp2 24 PETn2 25 GND 26 GND 27 PETp3 28 PETn3 29 GND 30 RSVD 31 PRSNT2# 32 GND Side A Description Name N/C N/C N/C Ground N/C N/C Ground 3.3 V power Not connected 3.3 V auxiliary power N/C PRSNT1# N/C N/C GND N/C JTAG3 JTAG4 N/C N/C +3.3V PERST# Mechanical key Reserved Ground Transmitter differential pair, Lane 0 Ground Hot-Plug presence detect Ground Transmitter differential pair, Lane 1 Ground Ground Transmitter differential pair, Lane 2 Ground Ground Transmitter differential pair, Lane 3 Ground Reserved Hot-Plug presence detect Ground GND REFCLK+ REFCLK GND PERp0 PERn0 GND RSVD GND PERp1 PERn1 GND GND PERp2 PERn2 GND GND PERp3 PERn3 GND RSVD Description Hot-Plug presence detect N/C N/C Ground Not connected TDI (Test Data Input) TDO (Test Data Output) Not connected Not connected 3.3 V power Fundamental reset Ground Reference clock (differential pair) Ground Receiver differential pair, Lane 0 Ground Reserved Ground Receiver differential pair, Lane 1 Ground Ground Receiver differential pair, Lane 2 Ground Ground Receiver differential pair, Lane 3 Ground Reserved Notes: 1. Optional signals that are not implemented are left as no connects on the board side connector. 2. Reserved signals are no connects on the board side connector. 3. Although support of CWAKE# is optional from the board side connector perspective, an allocated wire is mandated for the cable assembly. OSS-KIT-EXP-6002| 10 One Stop Systems 4. Board side pin-outs on both sides of the Link are identical. The cable assembly incorporates a null modem for the PCIe transmit and receive pairs. 4.4 PCI Express x4 Connector PIN Assignment 4.5 Pin-out for the PCIe x4 Cable Pin # A1 A4 A7 A10 A13 A16 B1 B4 B7 B10 B13 Cable Side 1 GND A2 PETp0 A3 PETn0 A5 PETp1 A6 PETn1 Pin # A8 A9 A11 A12 A14 A15 A17 A18 A19 B2 B3 B5 B6 B8 B9 B11 B12 B14 B15 B16 B17 B18 B19 Back shell Cable Side 1 PETp2 PETn2 PETp3 PETn3 CREFCLK+ CREFCLK SB_RTN CPRSNT# CPWRON PERp0 PERn0 PERp1 PERn1 PERp2 PERn2 PERp3 PERn3 PWR PWR PWR_RTN PWR_RTN CWAKE# CPERST# Chassis Ground OSS-KIT-EXP-6002| 11 Drain Wires Cable Side 2 GND Differential Pair Differential Pair PERp0 PERn0 PERp1 PERn1 Differential Pair Differential Pair Differential Pair Hook-up Wire Hook-up Wire Hook-up Wire Differential Pair Differential Pair Differential Pair Differential Pair NC NC NC NC Hook-up Wire Hook-up Wire Overall Cable Braid Cable Side 2 PERp2 PERn2 PERp3 PERn3 CREFCLK+ CREFCLKSB_RTN CPRSNT# CPWRON PETp0 PETn0 PETp1 PETn1 PETp2 PETn2 PETp3 PETn3 PWR PWR PWR_RTN PWR_RTN CWAKE# CPERST# Chassis Ground Pin # A1 A4 A7 A10 A13 A16 B1 B4 B7 B10 B13 B2 B3 B5 B6 Pin # B8 B9 B11 B12 A14 A15 A17 A18 A19 A2 A3 A5 A6 A8 A9 A11 A12 B14 B15 B16 B17 B18 B19 Back shell One Stop Systems 4.6 Signal Descriptions PETp(x) PETn(x) PERp(x) PERn(x) CREFCLK+/SB_RTN CPRSNT# PWR PWR_RTN CWAKE# CPERST# PCI Express Transmit Positive signal of (x) pair. PCI Express Transmit Negative signal of (x) pair. PCI Express Receive Positive signal of (x) pair. PCI Express Receive Negative signal of (x) pair. Cable REFerence CLocK: Provides a reference clock from the host system to the remote system. Side Band ReTurN: return path for single ended signals from remote systems. Cable PReSeNT: Indicates the presence of a device beyond the cable. PoWeR: Provides local power for in-cable redriver circuits. Only needed on long cables. Power does not go across the cable.) PoWeR ReTurN: Provides local power return path for PWR pins. Cable WAKE Cable PCI Express Reset 4.7 Connector Pin-outs for the PCIe x4 Cable Connector PIN# A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 OSS-KIT-EXP-6002| 12 SIGNAL GND PETp0 PETn0 GND PETp1 PETn1 GND PETp2 PETn2 GND PETp3 PETn3 GND CREFCLK+ CREFCLKGND SB_RTN CPRSNT# CPWRON GND PERp0 PERn0 GND PERp1 PERn1 GND PERp2 PERn2 GND PERp3 PERn3 GND PWR PWR PWR_RTN DESCRIPTION Ground reference Differential PCI Express Transmitter Lane 0 Ground reference Differential PCI Express Transmitter Lane 1 Ground reference Differential PCI Express Transmitter Lane 2 Ground reference Differential PCI Express Transmitter Lane 3 Ground reference Differential 100MHz cable reference clock Ground reference Side Band Return Used for detection of external cable and if downstream system is powered Turns power on / off to slave type downstream subsystems Ground reference Differential PCI Express Receiver Lane 0 Ground reference Differential PCI Express Receiver Lane 1 Ground reference Differential PCI Express Receiver Lane 2 Ground reference Differential PCI Express Receiver Lane 3 Ground reference +3.3V Cable Power Cable Power Return One Stop Systems B17 PWR_RTN B18 CWAKE# B18 CPERST# Power management signal for wakeup events (optional) Cable Reset# 4.8 PCI Express x4 Connector PIN Assignment CFG(0:2) BP PORT CFG 0 1 2 A0 A1 A2 A3 B0 0 0 0 X4 X4 X4 X4 X4 0 1 0 X8 0 X4 X4 X4 0 1 1 X8 0 X8 0 X4 1 X X X16 0 0 0 X4 OSS-KIT-EXP-6002| 13 One Stop Systems 5 Contacting Technical Support Our support department can be by phone at 1 (760) 745-9883. Support is available Monday through Friday, 8:00 AM to 5:00 PM PT. When contacting One Stop Systems Technical Support, please be sure to include the following information: 1) Name 2) Company Name 3) Phone Number 4) Fax Number 5) Email Address 6) Model Number 7) Serial Number 8) Computer Make 9) Computer Model 10) Operating System and Version 11) Make/Model of PCI cards in expansion chassis 12) Detailed description of the problem You can also visit our web site at: www.onestopsystems/support/ HT T For a quick response, use the Technical Support and RMA Request Form available in the Support Section of the website. Simply complete the form with all required information. Please make sure that your problem description is sufficiently detailed to help us understand your problem. For example: Don't say "Won't boot up." Do say "Tried all the steps in the Troubleshooting Section and it still won't boot up." For faster diagnosis of your problem, please run the two utility programs described in the following sections and include the diagnostic files they generate with your email. 6 Returning Merchandise to One Stop Systems If factory service is required, you must contact OSS Service Representative to obtain a Return Merchandise Authorization (RMA) number. Put this number and your return address on the shipping label when you return the item(s) for service. One Stop Systems will return any product that is not accompanied by an RMA number. Please note that One Stop Systems WILL NOT accept COD packages, so be sure to return the product freight and duties-paid. Ship the well-packaged product to the address below: RMA # ________ One Stop Systems 2235 Enterprise Street, Suite#110 92029 USA It is not required, though highly recommended, that you keep the packaging from the original shipment of your One Stop Systems product. However, if you return a product to One Stop Systems for warranty repair/ replacement or take advantage of the 30-day money back guarantee, you will need to package the product in a manner similar to the manner in which it was received from our plant. One Stop Systems cannot be responsible for any physical damage to the product or component pieces of the product (such as the host or expansion interfaces for the PCIe expansion chassis) that are damaged due to inadequate packing. Physical damage sustained in such a situation will be repaired at the owner's expense in accordance with Out of Warranty Procedures. Please, protect your investment, a bit more padding in a good box will go a long way to insuring the device is returned to use in the same condition you shipped it in. Please call for an RMA number first. OSS-KIT-EXP-6002| 14 One Stop Systems ass ONE STOP SYSTEMS 2235 Enterprise Street, Suite#llO, Escondido CA 92029 Toll-Free (800) 285-8990 US· Main (858) 530-2511 · Fax (858) 530-2733 www.onestopsystems.com OSS-KIT-EXP-6002| 15