User Manual for AMP models including: AMP15REMV2, 2AU29AMP15REMV2, Remote
Turnils North America AMP15REMV2 AMP Remote 2AU29AMP15REMV2 2AU29AMP15REMV2 amp15remv2
AMP15REMV2 Amp Remote by Turnils North America
File Info : application/pdf, 2 Pages, 906.35KB
DocumentDocumentDeclarations U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Quick Index Settings 1 Pairing 2 Switch Rotating Direction 3 Setting Upper & Lower Limits Steps P1 (hold down for 2s) > Stop (hold down for 2s) Up + Down (hold down for 2s) Upper Limit: Up (hold down for 2s) > Up + Stop (hold down for 2s) Lower Limit: Down (hold down for 2s) > Down + Stop (hold down for 2s) 4 Add / Remove Favorite Position P2 > Stop > Stop 5 Roller Mode & Sheer Mode Switch Up + Down (hold down for 5s) > Stop 6 Adjust Limits Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up + Stop (hold down for 2s) Lower Limit: Down + Stop (hold down for 5s) > Up or Down > Down + Stop (hold down for 2s) 7 Pair / Unpair Additional Emitter P2 (existing) > P2 (existing) > P2 (new) 8 Speed Regulation Acceleration: P2 > Up > Up Deceleration: P2 > Down > Down Troubleshooting Issues The motor has no response Possible Causes Solution Battery in motor is depleted Insufficient charging from Solar PV Panel Recharge with compatible AC adaptor and check connection and positioning of solar PV panel Check connection and orientation of solar PV panel Remote control battery is discharged Replace battery Battery is inserted incorrectly into remote control Radio interference / shielding Check battery polarity Ensure remote control and the antenna on the motor are positioned away from metal objects Receiver distance is too far from Remote Control Power failure Incorrect wiring Motor beeps 10 times when in use Battery voltage is low / PV (solar panel issue) Cannot program a single motor (multiple motors respond) Multiple motors are paired to the same channel. Move remote control to a closer position Check power supply to motor is connected and active Check that wiring is connected correctly (refer to motor installation instructions) Recharge with AC adapter or check connection and positioning of solar PV panel Always reserve an individual channel for programming functions SYSTEM BEST PRACTICE - Provide an extra 15 channel remote in your multi-motor projects that provides individual control for each motor for programming purposes Place all other motors into sleep mode (Press "P1" button (about 6 sec) on the motor head until motor jog x2 and beep x2). AMPTM Remote Fields of Application Roller Sheer Banded Roman Cellular/Honeycomb Cellular/Honeycomb Standard Skylight Tilt-Only Horizontal Narrow Width One-Way Left Stack One-Way Right Stack Specifications Two-Way Split Stack Voltage Radio Frequency Transmitting Power Operating Temperature RF Modulation Lock Function IP Rating Transmission Distance 3V (CR2450) 433.92 MHz Bi-directional 10 milliwatt 14°F to 122°F (-10°C to 50°C) FSK Yes IP20 up to 200m (outdoor) Safety Instructions 1. Do not expose motor to humid, damp, or extreme temperature conditions. 2. Do not drill into motor. Declarations AMP25B 3. Do not cut the antenna. Keep it clear from metal objects. Add A zoom in on the charging port 4. Do not allow children to play with this device. 5. If the power cable or connector is damaged, do not use. 6. Ensure the correct crown and drive adaptor are used. FCC Text - text 01 Roller Sheer Revolve Roman shades 7. Ensure the power cable and aerial is clear and protected from moving parts. 8. Cable routed through walls should be properly isolated. , sheer shadings, roman shades, and zebra shades. P1 9. Motor is to be mounted inAMPh25B orizontal position only. AMP25B Add visual explanation of P1 - file 02 10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation. 11. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty. Safety Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. Please scan QR code to see more AMPTM product information Button Instructions P2 P1 Button P2 Switch LED light Power line P1 button AMPTILT Lithium Battery Switch AMP25B / AMP28B / AMP35B / AMP25BDC Replace/Install CR2450 Battery a. Gently insert the included ejector tool into the a. small pinhole opening and apply a small amount of pressure to the cover and slide the cover off. b. Install battery (CR2450) with positive (+) side facing up. c. Gently slide the cover back on until a "click" sound is heard. Signal line P1 Button AMPCEL b. Battery (CR2450) c. click Advanced Setting - Disable Limit Setting a. Remove the cover from the backside of remote, the lock switch is in the right corner. b. Move the switch to the "Lock" position to disable the following commands, remote will show "L" (lock): - Change Motor Direction - Setting the Upper and Lower Limit - Adjust Limit - Roller Mode or Sheer Mode c. Move the switch to "Unlock" position to assess all remote functions, remote will show "U" (unlock). a. Switch b. Unlock Lock L Switch *This advanced feature is intended to be used after all shade programming is completed. User Mode will prevent accidental or unintended changing of limits. c. Unlock Lock U Switch Channel Options Select A Channel a. Press "<" button on the remote to select a lower channel. b. Press ">" button on the remote to select a higher channel. Action on a. Remote Control Lower Channel Remote 1 Response b. Higher Channel 15 Hide Unused Channels a. Press and Hold (about 3 sec) "<" and ">" buttons simultaneously until remote control displays "C" (channel). Action on a. Remote Control b. Press "<" or ">" button to select required quantity of channel (between 1 to 15). Remote Response c. Press "Stop" button to confirm selection (the example shows a 5-channel selection). The LED will display "o" (OK) once to confirm selection. Action on b. Remote Control Remote Response Action on c. Remote Control Remote Response + Lower Higher Channel Channel C or Lower Higher Channel Channel 11 Stop o 5 ! Essential Settings The steps in factory mode must be completed to ensure proper operation. * AMPCEL and AMPTILT motors DO NOT BEEP. 1. Pair / Unpair Remote Control a. Press "P1" button (about 2 sec) on Action on a. P1 P1 the motor head until motor jog x1 and Motor P1 beep x1. b. In the next 10 secs, press and hold "Stop" button on the remote control until motor jog x2 and beep x3. * Repeat the same procedure to unpair remote control. Motor Response Action on b. Remote Control Motor Response Jog x1 Beep x1 Stop Jog x2 Beep x3 2. Change Motor Direction (if necessary) Press "Up" or "Down" button to check if the shade moves in the desired direction. If you need to reverse the direction, press and hold (about 2 sec) "Up" and "Down" buttons simultaneously until motor jog x1 and beep x1. Action on Remote Control *The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing "P1" button (about 10 sec) on the motor head until motor jog x3 and beep x3. Motor Response + Up Jog x1 3. Setting the Upper and Lower Limits Down Beep x1 3.1 Set Upper Limit Action on a. Remote Control a. Press "Up" button to raise the shade, Up then press "Stop" button when it is in the desired upper limit. Motor Response b. Press and hold (about 5 sec) "Up" and "Stop" buttons simultaneously until motor jog x2 and beep x3. b. Up + Stop Jog x2 Beep x3 3.2 Set Lower Limit a. Press "Down" button to lower the shade, then press "Stop" button when it is in the desired lower limit. b. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on a. Remote Control Down Motor Response b. + Down Stop Jog x2 Beep x3 *If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits. Factory Mode Complete User Mode Begins 4. Adjust Limits 4.1 Adjust the Upper Limit a. Press and hold (about 5 sec) "Up" and "Stop" buttons simultaneously until motor jog x1 and beep x1. b. Use "Up" button to raise the shade to the desired highest position, and use "Up" or "Down" button to do the final adjustment if necessary. c. Press and hold (about 5 sec) "Up" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on a. Remote Control Motor Response Action on c. Remote Control Motor Response + Up Stop Jog x1 Beep x1 + Up Stop Jog x2 Beep x3 b. Up 4.2 Adjust the Lower Limit a. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x1 and beep x1. b. Use "Down" button to lower the shade to the desired lowest position, and use "Up" or "Down" button to do the final adjustment if necessary. c. Press and hold (about 5 sec) "Down" and "Stop" buttons simultaneously until motor jog x2 and beep x3. Action on a. Remote Control + Down Motor Response Jog x1 Action on c. Remote Control + Down Motor Response Jog x2 Stop Beep x1 Stop Beep x3 b. Down 5. Favorite Position 5.1 Set Favorite Position a. Use "Up" or "Down" button to move the shade to desired Favorite position. Action on a. Remote Control Up or b. P2 Down b. Press one "P2" button on the back of remote control until motor jog x1 and beep x1. Motor Response or c. Press "Stop" button until motor jog x1 and beep x1. Action on c. d. Once more, press "Stop" button until Remote Control Stop motor jog x2 and beep x3. d. Stop Jog x1 Beep x1 Motor Response 5.2 Send Shade to Favorite Position Press and hold (about 2 sec) "Stop" button, motor will move to Favorite position. Action on Remote Control Shade Response Jog x1 Beep x1 Jog x2 Beep x3 Stop or 5.3 Delete Favorite Position a. Press one "P2" button until motor jog and beep x1. b. Press "Stop" button until motor jog and beep x1. c. Once more, press "Stop" button until motor jog x1 and long beep x1. Action on a. Remote Control Motor Response Action on c. Remote Control Motor Response P2 b. Jog x1 Beep x1 Stop Jog x1 Beep x1 Stop Jog x1 Beep x1 6. Roller Mode and Sheer Mode 6.1 Roller Shade Mode - continue movement after a short press Default Mode Action on a. Remote Control a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jog x1. b. Press and hold (about 2 sec) "Stop" button until motor jog x2 and beep x3. Motor Response Action on b. Remote Control Motor Response + Up Down Jog x1 Stop Jog x2 Beep x3 6.2 Sheer Shade Mode - jog movement after a short press (continue movement after a long press) a. Press and hold (about 5 sec) "Up" and "Down" buttons simultaneously until motor jog x1. b. Press and hold (about 2 sec) "Stop" button until motor jog x1 and beep x1. Action on a. Remote Control Up + Down Motor Response Jog x1 Action on b. Remote Control Motor Response Stop Jog x1 Beep x1 7. Add or Remove Additional Remote 7.1 Using Current Remote Control a. On the current remote control, press one "P2" button until motor jog x1 and beep x1. b. Once more, on the current remote control, press one "P2" button until motor jog x1 and beep x1. c. On the New remote control, press one "P2" button until motor jog x2 and beep x3. Action on a. Current Remote Control Remote Control P2 Motor Response Jog x1 Beep x1 Action on c. New Remote Control Remote Control P2 b. Current Remote Control P2 Jog x1 Beep x1 *Repeat the same procedure to remove additional remote control. Motor Response Jog x2 Beep x3 7.2 New Remote Control Follow instructions under the section 1. Pair / Unpair Remote Control 8. Adjust Motor Speed 8.1 Acceleration Speed Action on a. P2 b. Remote Control a. Press one "P2" button until motor jog x1 and beep x1. b. Press "Up" button until motor jog x1 and beep x1. c. Once more, press "Up" button until motor jog x2 and beep x1. Motor Response Action on c. Remote Control Jog x1 Beep x1 Up Up Jog x1 Beep x1 Motor Response Jog x2 Beep x1 8.2 Deceleration Speed a. Press one "P2" button until motor jog x1 and beep x1. b. Press "Down" button until motor jog x1 and beep x1. c. Once more, press "Down" button until motor jog x2 and beep x1. Action on a. Remote Control Motor Response Action on c. Remote Control P2 Jog x1 Beep x1 Down b. Down Jog x1 Beep x1 *If the motor has no response, it already has a Maximum or Minimum speed. Motor Response Jog x2 Beep x1Adobe PDF Library 15.0 Adobe InDesign 16.2 (Macintosh)