User Manual for Kon-TEC models including: KT-04 4 Channel Battery Equalizer, KT-04, 4 Channel Battery Equalizer, Channel Battery Equalizer, Battery Equalizer, Equalizer
20 ore fa — n – numer of batteries connected in series, min. 2, max. 4. Page 3. User manual. LiFePO4 4-channel battery ...
1 day ago — n – numer of batteries connected in series, min. 2, max. 4. Page 3. User manual. LiFePO4 4-channel battery ...
LiFePO 4 4-channel battery equalizer KT-04 User manual Kon-TEC Sp. z o.o. @ Ï7Í÷ ÷7d( ÷ @Qíî Q u ñ 6 Q Qïñ7íìñQ ÷d A jðôQñóîQììíQíñì
File Info : application/pdf, 4 Pages, 379.40KB
DocumentDocumentUser manual www.kon-tec.eu LiFePO 4-channel 4 battery equalizer KT-04 Kon-TEC Sp. z o.o. Boya-eleskiego 12, Building B, 35-105 Rzeszów +48 572 001 150 info@kon-tec.eu LiFePO4 4-channel battery equalizer KT-04 1. TECHNICAL DATA PARAMETER LiFePO4 Battery nominal voltage Number of LiFePO4 batteries connected in series Optimizing current Quiescent current Dimensions Protection Low voltage disconnect n numer of batteries connected in series, min. 2, max. 4. User manual VALUE n*12V LiFePO4 Min. 2, Max. 4 0-1,5A <3mA 150x140x40 mm Thermal protection n*10V LiFePO4 02 LiFePO4 4-channel battery equalizer KT-04 User manual 2. GENERAL INFORMATION The KT-04 equalizer is used, when LiFePO4 batteries are connected in series, to maintain the voltage of each battery at the same level, during charging process. During operation of batteries connected in series, their voltages may vary due to the chemical composition of the cells or their temperature. The self-discharge process also impacts the voltage difference, which is slightly different for each cell. Due to the fact that the cells are not the same, they behave differently. Then the batteries are unstable, e.g. one of the battery is overcharged and the other is undercharged. Additionally, differences in the voltages of the batteries, connected in series, occur before the load is connected. Connecting batteries in series without equalizer may cause premature battery degradation. 3. OPERATION AND APPLICATION KT-04 equalizer works with the principle of electricity transfer. The device starts working when: > one of the batteries charging voltage reaches 14V, > the voltage difference between two or more batteries is 0,1V. The equalizer is connected all the time to the battery to automate the energy balancing process without the need of manual intervention. 4. TERMS OF USE 4.1. The KT-04 equalizer is intended for use with dedicated Kon-TEC batteries and chargers. 4.2. It is not recommended to leave the equalizer connected to batteries that are not used for a long period of time (couple months). In this case, the device's low current consumption may cause discharge of batteries. Periodic control of state of charge status is recommended. triangle ATTENTION Failure to follow the instructions may result in damage to the device, battery, charger or even cause a fire. 4.3. Installation. Connect as follows: > First, screw the wires into the plug. > Then connect each of the wires to proper battery terminals. > Finally, install the plug into the equalizer socket. The drawings show the correct connections of the equalizer with batteries (different voltage configurations). 24V -+ -+ 36V -+ -+ -+ 48V -+ -+ -+ -+ 03 Kon-TEC Sp. z o.o. Boya-eleskiego 12, Building B 35-105 Rzeszów +48 572 001 150 info@kon-tec.eu www.kon-tec.eu