Celsius Oil Filled Radiator Instruction Manual

Safety Instructions

• Read the manual before use and keep for future reference.
• Check that the heater and accessories are complete and intact.
• The heater must be installed as per installation instructions and plugged into a socket meeting AC 230V, 50/60Hz requirements.
• The heater is suitable for indoor use only.
• Do not use the heater near flammable or explosive materials.
• Inserting items into the protective grill of the heater is strictly prohibited.
• The metal housing gets hot during use; allow the heater to cool before handling.
• Unplug the heater if it is out of use for a long time.
• Prior to each use, ensure the heater is in good condition and intact. Do not use if the casing, wire, or plug are damaged.
• The heating element may be damaged if the heater is dropped or hit; do not use if the element is broken.
• Unplug from the socket when moving or cleaning the heater. Flick the switch to the off position before unplugging; do not pull the cable.
• The heater must not be located immediately below an electrical socket-outlet.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to avoid a hazard.
• Avoid using an extension cord as it may overheat and cause a fire risk.
• Never place the heater where it may fall into water.
• CAUTION: Some parts of this product can become very hot and cause burns. Particular attention must be given where children and vulnerable people are present.
• CAUTION: Never cover the heater. Covering the heater risks overheating and fire.

Technical Data

Installation Instructions

Clearances:

• A gap of at least 60mm below the heater.
• At least 100mm above the heater to any window frame.
• At least 650mm to the ceiling.

The radiator must be installed horizontally, not vertically.

Installation Steps:

1. Position the wall brackets on the wall as a guide ruler, ensuring the holes are level, then mark the hole positions.
2. Drill holes on the wall using an 8mm drill bit and insert the plastic wall plugs.
3. Fasten the hanging rack on the wall with screws, ensuring it is correctly oriented.
4. Insert the bottom of the heater body onto the hanging rack first, then push the heater body to hook it onto the entire hanging rack.

Warning: When drilling holes, always check to ensure there is no wiring, pipework, etc., in the area to be drilled.

Warning: Before plugging in the unit, make sure the radiator is properly attached to the wall.

Visual Description: Diagrams illustrate the wall mounting process, showing brackets, drilling, and hanging the heater.

Key Pad and Operation

Key Pad Description

• Heat Indicator: Light illuminated indicates the heater is heating. If the light does not appear, the room has reached the desired temperature.
• WiFi Light: Solid light indicates WiFi is connected; blinking light indicates WiFi connection is ready.
• Countdown Timer Button: Press to select how many hours the heater will stay on (1-8 hours).
• On / Off Button: Press to set the heater On or into standby mode.
• WiFi Button: Hold to reset WiFi.

Using the Heater

To Start:

Plug the appliance into an AC220-240V 50-60Hz socket. Press the "ON/OFF" button; the display will light up, and the heater will switch on.

Boot Heating:

After switching on, the heater will start heating. The temperature must be set using the '+' or '-' buttons to enable the thermostat.

Temperature Adjustment:

Initially, the display shows the current room temperature. Pressing the '+' or '-' buttons will show the target temperature. Press '+' or '-' to change the heater's target temperature.

Countdown Timer Button:

Press to set how many hours the heater will stay on (1-8 hours).

WiFi Button:

Hold "WIFI" for 5 seconds to set up the WiFi function.

Smart App Control

Downloading the App

Before connecting the Celsius heater to WiFi, download the 'Smart Life' app onto your smartphone or tablet. You can find the app by scanning the provided QR code (not included here) or searching "Smart Life" in the Google Play or Apple app store. After downloading, open the app and create an account.

Connecting to WiFi

Initial Setup:

1. Open the 'Smart Life' app at the home screen.
2. Press the '+' button to add the heater.
3. Select 'Heater' from the list of devices, which may be found under "small home appliances".

Visual Description: App screenshots show the device list and the process of adding a new device.

WiFi Configuration:

1. Enter your WiFi details (SSID and password) and press 'Next'. Ensure you select a 2.4 GHz Wi-Fi network.
2. Reset the device: Press and hold the heater's WiFi button for 5 seconds until the WiFi light begins to flash. Repeat this until the WiFi light flashes slowly.
3. Once the light flashes slowly, press 'Next' in the app.
4. Select "Blinking or Breathing slowly" in the app to match the heater's indicator light status.

Visual Description: App screenshots guide through entering WiFi details, resetting the device, and selecting the indicator light status.

Connecting to Heater's Hotspot:

1. Connect your mobile phone to the device's hotspot, typically named "SmartLife****".
2. In the app, press the "Go to Connect" button, which opens your phone's settings.
3. Go to the list of WiFi networks and connect to the "SmartLife****" network.
4. Once connected, return to the heating app.

Visual Description: App screenshots show connecting the phone to the device's hotspot.

App Connection Process:

The app will now begin to connect. The heater may take a few minutes to connect and pair with your WiFi network. The app will then prompt you to name the device. Once connected, the device is confirmed added, the heater will beep, and the WiFi light will illuminate. You can now name the device, share it with family members, or proceed to scheduling.

Visual Description: App screenshots show the connection progress and successful device addition.

Using the App

You can use the app to control multiple devices. The device list shows the status of your devices:

• Offline: Device is turned off at the wall or disconnected from the power supply.
• Turned Off: Device is in standby mode.
• Turned On: Device is in heating mode.

Tap the device name to go to the control interface. Note: You cannot control the heater from the app when it is offline.

In the control interface, you can:

• Turn the heater ON/OFF using the "Switch" button.
• Change the heater's set temperature using the '+' and '-' buttons.
• Set a countdown timer for the heater to switch off after 1-8 hours.

Visual Description: An app screenshot shows the control interface with temperature settings and timer options.

Scheduling the Heater

You can schedule the Celsius heater to switch on and heat at different temperatures throughout the day using the 'Scene' menu in the app.

Creating Scenes:

1. From the app's home screen, press "Scene".
2. On the scene screen, you can create "Scenes" to schedule the heater.
3. "Scenes" allow you to send commands to the heater at particular times, such as setting the thermostat to 20 degrees at 9 o'clock or to 5 degrees at 12 o'clock.

Visual Description: App screenshots illustrate navigating to the 'Scene' menu and the scene creation interface.

Refer to "Timing the heater" for detailed steps on setting temperatures at different times.

Timing the Heater

Timing works by sending a command to the heater at a scheduled time. This command sets the heater's thermostat temperature for desired On and Off times.

Recommended Settings:

• Set thermostat around 18 degrees when the room needs to be warm.
• Set around 10 degrees for anti-frost or away mode when the room is not in use.

You can create multiple commands to set various time intervals as needed.

Scheduling Steps:

1. Press "Create Scene".
2. Press "Schedule".
3. Press "Next" to continue.
4. Select the days you want the schedule to apply to. Press '<' to return if needed.
5. Enter the desired time for the command and press "repeat".
6. Press "Add Task".
7. Press "Run the device".
8. Select the device you wish to program by pressing its name.

Visual Description: A series of app screenshots detail the scheduling process from creating a scene to selecting the device.

Setting Functions:

1. Select "Switch" and choose "On", then Save.
2. Press "Set Temperature".
3. Select the desired temperature for that time and press Save to continue.
4. Once "Switch" and "Set Temperature" values are entered, press "Next".
5. You will arrive at a screen where you can rename the command (e.g., "9 am turn on").
6. You can also choose to command another device at the same time.
7. Press "Save" to finish.

Visual Description: App screenshots show setting the ON/OFF switch, temperature, and saving the timed command.

A second scene is needed to switch the heater off or to a lower room temperature (anti-frost mode). Otherwise, the heater will maintain the first temperature set.

This process allows you to time the heater. Repeat this process to schedule more temperatures or ON/OFF times.

Important Notes:

• When switching the heater ON, a temperature must also be set; otherwise, "Boot Heating" will be enabled.
• If the Switch is set to OFF, a temperature cannot be set as the heater will be in standby mode.

ERP LABEL

Model identifier(s): Celsius

Contact Details

Manufacturer: Sol*Aire Heating Products

Address: Big Shed, New Row, DL11 7AW

Email: info@solairehp.co.uk

Tel: 01325717899

Warranty and Disposal

The product is for household use only.

Correct Disposal of this product

This marking indicates that the product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Visual Description: A symbol showing a crossed-out wheeled bin indicates proper disposal guidelines.

Warranty Information

• The manufacturer provides warranty in accordance with the legislation of the customer's own country of residence.
• The product has a 2-year Guarantee in the UK.
• The warranty only covers defects in material or workmanship.
• Repairs under warranty may only be carried out by an authorized source.
• When making a claim under the warranty, the original bill of purchase (with purchase date) must be submitted.

The warranty will not apply in cases of:

• Normal wear and tear.
• Incorrect use, e.g., overloading of the appliance, use of non-approved accessories.
• Use of force, damage caused by external influences.
• Damage caused by non-observance of the user manual, e.g., connection to an unsuitable mains supply or non-compliance with the installation instructions.
• Partially or completely dismantled appliances.

Declaration of Conformity

This product conforms to the following European Directives:

• 2014/30/EU (EMC)
• 2014/35/EU (LVD)
• 2011/65/EU (RoHS)
• 2009/125/EC (ErP) + Regulation (EU) 2015/1188

Visual Description: The product displays CE and UKCA conformity marks.