User Manual for Jetec Electronic models including: N OQVU.PEFM, RS485-, RS485, ALM2, ALM1, ExTempMini Series Infrared Temperature Sensor, Infrared Temperature Sensor, Temperature Sensor, Sensor
Join system User Manual Address: No. 11, Furen Street, West District, Taichung City Tel: 04-23729418 Fax: 04-23724011 E-mail: sales@jetec.com.tw Electrical connection/Wiring connection N"*OQVU.PEFM GND GND issueC/20230308/V3 C4 C3 C2 C1 GND Vcc ++ + + mA mA mA mA -- - - - + 12VDC Input, 24VDC Input*(Option) ALM2(C2) ALM1(C1) C1~C4Channel 1~Channel 4 mA4-20mA ALM1,ALM2Relay Output.(Relay 1 & Relay 2 correspond to C1 & C2 of signal input) *For this model, the wiring will be connected and the range will be set before shipping. 34*OQVU.PEFM B- A+ RS485- RS485+ GND Vcc - + 12VDC Input, 24VDC Input*(Option) ALM2 ALM1 ALM1,ALM2Relay Output.(Relay 1 & Relay 2 correspond to Channel 1 & Channel 2) *This model needs to be wired by yourself, please make sure the RS-485 positive and negative before wiring. Company ID (required for account sign in) COMPANY ID ! WARNING There is a risk of electrical shock and damage to the device from any power supply connection. It is not recommended that any non-technical personnel perform this type of action. ! WARNING Please make sure that the power is turned off before connecting any wires. ! WARNING Please use the correct power source and voltage, and check whether the power supply type and polarity are correct before powering on. 1 Network configuration Skip to Step9 if the user has ordered a full set with the router from JETEC ELECTRONICS STEP 1 Please toggle the switch on the device to the position as shown in the figure, then turn on the power STEP 2 When both the yellow and green lights on, you are ready to set up a Wi-Fi connection. *If only one of the lights is on or neither of them is on, please just turn off the power and repeat step 1. If the condition persists, please contact us. STEP 3 Download "Join-System" from the APP store. *Android10.0() Android 10.0 cancel STEP 4 Turn on the wifi function and connect the ID starting with "Jetec_AP_XXXXXX". Then enter the default password: 23729418 Open 2 STEP 5 First, configure the wifi Internet in LAN mode. Open the Root Page, and click "Get Start!" on the "Join-LAN" system box STEP 6 1. Click" " 2. Select "AP Connection Mode" 3. Then click on the device you want to set up wifi access. STEP 7 ... 1. Click" " 2. Select"Set wifi" 3. Select the wifi you want to connect your device to the Internet and enter the password 4. When the device is successfully connected to wi-Fi, a notification message will pop up. Device 1 Device 1 Device 1 3 STEP 8 Please power off the device after complete the settings, then toggle back the switch to the position as shown in the figure, and re-powering the device. STEP 9 -After power on the device,it will automatically connect to the network and upload the data. -During the process,the red light would flashing regularly. -If not,make sure that the Wi-Fi router is working properly and connected to the network again. 4 APP instruction (For Android6.0 and IOS 10 version or above) *Android10.0()Android 10.0 Enter APP First, configure the wifi Internet in Cloud mode. Open the Root Page, and click "Get Start!" on the "Join-Cloud" system box Account login Fill in the following to sign in : 1Company ID : refer to the information on page 1. 2Account: company ID has the highest authority in the system.Users are able to add other accounts in "Members managment" 3Password: default passwords are"000000".Passwords are settable,and can be reset in PC version. JETEC Electronics Co., Ltd. 5 Address: No. 11, Furen Street, West District, Taichung City Tel: 04-23729418 Fax: 04-23724011 E-mail: sales@jetec.com.twAdobe PDF library 16.04 Adobe Illustrator 26.2 (Windows)