LAVOR Express Residential High Pressure Washer

Components

• A: On/Off Switch
• B: Power Cable
• C: Water Inlet
• D: High Pressure Water Outlet
• E: Water Filter
• F: Water Inlet Connection (3/4")
• G: Carrying Handle
• H: High Pressure Hose
• I: Trigger Gun with Safety Lock
• J: Lance with Jet Adjustment
• K: Nozzle Cleaning Needle
• L: Detergent and Foam Diffuser Reservoir
• M: Instruction Manual
• N: National Network of Authorized Service Centers
• O: Handle Fixing Screws

Unpacking

After unpacking the washer, check that it has all standard accessories and is free from damage. If in doubt, do not use the washer and return it to the place of purchase.

Safety Warning: Packaging materials (plastic bags, styrofoam, screws, etc.) should not be left within reach of children as they can be a potential source of danger.

Technical data may change due to variations in the electrical and hydraulic network.

Safety Precautions

• WARNING: The washer must only be used for its intended purpose, domestic/residential use. Any other use is considered improper and therefore dangerous. The manufacturer is not responsible for any damage caused by improper, incorrect, or unreasonable use.
• WARNING: Disconnect the washer from the hydraulic and electrical supply before any cleaning/maintenance.
• WARNING: If the power supply is interrupted, turn off the washer at the switch.
• WARNING: When using cleaning products in the reservoir (L), preferably use neutral products or additives (Shampoo) with a pH between 6 and 8. Using other cleaning products or chemical substances may compromise the durability of the washer.
• WARNING: Do not pull the power cord or the washer to unplug from the socket.
• WARNING: Do not use the washer with a damaged power cord. If the cord is damaged, it must be replaced by the manufacturer, an authorized service center, or a qualified electrician to avoid risks.
• WARNING: Do not touch the product with wet hands or bare feet.
• WARNING: Use the washer in ventilated areas and never cover or obstruct the air inlets.
• WARNING: Do not turn on the washer without first unwinding the high-pressure hose (H).
• WARNING: Do not use the washer if any components are damaged. The high-pressure hose, trigger gun, lance, accessories, and high-pressure connectors are important for the safety of the washer. Use original parts for replacement.
• WARNING: The product should not be used by children or persons with reduced physical, sensory, or mental capabilities, unless they have been adequately trained or instructed.
• WARNING: Children, even if supervised, should not play with the washer.
• WARNING: Do not use the washer near people, unless they are wearing appropriate protective clothing.
• WARNING: During use, wear protective clothing according to safety standards, such as safety glasses and non-slip shoes.
• WARNING: High-pressure water jets can be dangerous if used improperly. Do not direct the jet at yourself, others, animals, or your clothing/footwear, as it can cause serious injury. Do not direct the jet at the washer, other equipment, or electrical installations.
• WARNING: The washer is equipped with a nozzle that determines the technical characteristics of the appliance. Any alteration to the diameter of this opening will affect the technical characteristics of the equipment.
• WARNING: Operating the trigger gun causes a kickback.
• WARNING: Protect the equipment from freezing. Avoid storing the washer in cold places.
• Do not operate the washer without water. Lack of water, even for a short period, can damage the pump.

Electrical Supply

• The electrical connection must comply with standard IEC 364.
• Before connecting the washer, ensure that the information on the technical data label matches your electrical network and that the socket is protected by a residual current device (RCD) with a tripping current of less than 0.03 A - 30 ms.
• If the socket and the washer plug do not match, have the socket replaced by qualified personnel.
• Ensure the electrical wiring can support the power absorbed by the washer.
• WARNING: Inappropriate electrical extensions can be dangerous.
• Extension cords are not recommended. If essential, use one that complies with current safety standards for quality and capacity. Ensure the extension cord is on a dry surface and that the plug and socket are waterproof to prevent electric shock. The cable must have the dimensions indicated in the table:
  • 230-240V: 1.5 mm² up to 20 meters, 2.5 mm² up to 30 meters
  • 100-120V: 2.5 mm² up to 20 meters, 4.0 mm² up to 30 meters

Operation

Installation and Operation

1. Place the filter (E) into the water inlet (C). (Fig. 1)
2. Screw the 3/4" connection (F.1) onto the water inlet (C). (Fig. 2)
3. Unscrew the fixing ring of the 3/4" connection (F.2). (Fig. 3)
4. Pass the garden hose through the opening of the 3/4" connection fixing ring (F.2) and connect the hose to the 3/4" connection (F.1). (Fig. 4)
5. Screw the fixing ring (F.2) onto the 3/4" connection (F.1). (Fig. 5)
6. Connect the high-pressure hose (H) to the trigger gun (I) and tighten with a 17mm wrench. (Fig. 6) Ensure it is tightened with the wrench.
7. Connect the high-pressure hose (H) to the water outlet (D) and screw it on. (Fig. 7) Be careful not to cross-thread. Ensure the hose is fully screwed on.
8. Connect the power cable plug (B) to the power outlet according to the voltage. (Fig. 8) Verify the voltage of your electrical network before connecting the washer.
9. Open the water supply tap or valve. (Fig. 9)
10. Turn on the washer by pressing the switch (A) to the ON (I) position. (Fig. 10)
11. Pull the trigger and wait for 2 minutes or until water comes out of the trigger gun tip (I). This operation is to remove air and should be done without the lance (J) connected. (Fig. 11)
12. Release the trigger and connect the lance (J) to the trigger gun (I). Simply fit the lance into the gun and turn clockwise until locked. (Fig. 12) Note: To disassemble or assemble accessories, the washer must be turned off or depressurized. Never change accessories with the trigger gun (I) pulled.
13. The installation is complete. The washer can now be used for domestic purposes, such as cleaning cars, motorcycles, facades, sidewalks, etc. (Fig. 13)
14. The lance (J) has jet adjustment. Rotate the knob at the end of the lance to obtain a fan jet or a concentrated jet. (Fig. 14) Recommendation: Exercise special care when using the concentrated water jet on paintwork and coatings.
15. (*) The garden hose is not supplied with the washer.

Using Detergent

1. Pour the detergent into the reservoir (L.1). (Fig. 16)
2. Attach the foam diffuser with hose (L.2). (Fig. 17)
3. Fit the diffuser onto the reservoir and turn to lock. (Fig. 18)
4. Attach the assembled reservoir (L) to the end of the lance (J). (Fig. 19)
5. Adjust the jet to find the ideal additive suction point.
6. The additive will be dispensed at low pressure.

Trigger Gun Safety Lock

1. When interrupting the use of the washer, activate the safety lock (colored pin on the trigger gun handle) to prevent accidental spraying. To lock, simply press the locking pin of the trigger gun. (Fig. 20)

Cleaning the Nozzle

1. If pressure is lost or the spray is uneven:
2. Disconnect the lance (J) from the trigger gun (I). (Fig. 20)
3. To clean the nozzle, insert the cleaning needle (K) into the nozzle hole of the lance (J). (Fig. 21)

Cleaning the Water Filter

1. Before and after using the washer, clean the water filter (E):
2. Remove the filter (E) from the water inlet (C). (Fig. 22)
3. Rinse it under running water with the larger opening facing downwards. (Fig. 23)

Disconnecting the Washer

1. Turn off the washer by pressing the switch (A) to the OFF (O) position. (Fig. 24)
2. Unplug the power cable (B) from the power outlet. (Fig. 25)
3. Close the water supply tap or valve. (Fig. 26)
4. Pull the trigger gun (I) trigger to release all pressure. (Fig. 27)
5. Engage the trigger gun safety lock. (Fig. 28)

Handle Assembly

1. Fit the handle onto the casing by pushing forward until it rests and the screw holes are visible. (Fig. 29)
2. Insert the screws into the holes and use a Phillips screwdriver to tighten the handle to the casing. (Fig. 30)

Maintenance

• In case of malfunction or poor performance, turn off the product and do not attempt to repair it. Contact an Authorized Service Center for repairs, requesting the use of original parts. Failure to comply with the above may compromise product safety and void the warranty.
• Do not allow untrained or unqualified personnel to repair your washer.
• If parts need to be replaced, always use original parts.
• The washer has a closed-loop lubrication system and does not require oil refills.
• The washer is for domestic use. Preventive maintenance by an authorized service center is recommended after 200 hours of use.

Warranty Certificate

The warranty certificate is available with the National Network of Authorized Service Centers.

Optional Accessories

• Turbo Lance (Turbo Nozzle): Connect the turbo lance and rotate until locked. Provides a rotating jet that boosts the washer's cleaning power.
• Drain Cleaning Hose: Connect the hose end and rotate until locked. This 6-meter long hose is easy to use for unclogging pipes.
• Rotating Brush: Connect the rotating brush and rotate until locked. Its soft bristles are specially designed not to damage surfaces. Recommended for cars and windows.
• Hose Extension: With your hands, release the hose connection attached to the washer. Using 17mm and 22mm wrenches, connect and tighten the fittings. Ensure there are no leaks at the connections. With your hands, screw the hose connection onto the washer. This additional hose can be connected to the standard hose, extending its reach by up to 10 meters.
• Surfer: Easy to use, the Surfer provides better performance in floor cleaning. Its design with rotating water jets offers powerful cleaning. It has a handle for easier wall cleaning. With pressure regulation, it is ideal for cleaning sensitive surfaces.

Cleaning Tips

• Exercise special care when using the concentrated water jet on paintwork and coatings.
• The washer should only be used for domestic purposes, such as cleaning cars, motorcycles, yards, facades, barbecues, etc.
• To remove dirt, wash the surface, removing the most caked-on dirt first.
• After removing the dirt, rinse the surface thoroughly to remove residues.

Troubleshooting

• Washer does not work: Check the mains voltage. Check if the power cord is damaged.
• Washer has no pressure or strong pressure fluctuations: Check if the water inlet tap/valve is open. Check the water inlet and outlet connections. Remove air from the system. Clean the water inlet filter. Check if the lance nozzle is clogged.
• Washer drips: Up to 10 drops per minute are acceptable. For greater water loss, contact an authorized service center.

Spare Parts

Use only original spare parts.

Automatic Stop System (A.S.S.)

Observation: This high-pressure washer is equipped with the A.S.S. (Automatic Stop System), which automatically shuts off the washer during the bypass phase. When the trigger gun is released, the A.S.S. system will shut off the washer. When the trigger gun is activated, the motor will restart. Automatic starts of the washer without the trigger gun being activated may be due to air bubbles in the water. If the washer remains in standby (not operating) for more than 5 minutes, turn off the washer at the switch to the "OFF" position and pull the trigger to release air.

Contact Information

Lavorwash Brasil Industrial e Comercial Ltda.
Rua Manoel Gomes dos Santos, nº 2.961 - Setor Industrial
CEP 14140-000 - Cravinhos - SP
Tel: +55 16 3951-9666 / Fax: +55 16 3951-9669
www.lavorwash.com.br

S.A.L. - Serviço de Atendimento Lavor
0800-770-2715

Important Notice

ATTENTION: Read the instructions before use. Domestic Use.