iGPSPORT SRTL SR30 Smart Radar Tail Light User Manual

1. Introduction

The SRTL SR30 Smart Radar Tail Light is a safety auxiliary device that detects vehicles within a certain range behind the rider, providing two-way reminders for both the user and approaching vehicles. It features a micro radar and a multi-mode tail light. The radar actively detects approaching vehicles and displays them on a terminal device, while the tail light actively alerts vehicles behind. This combination enhances environmental awareness and ensures riding safety. While the device aids in detection, it is not a substitute for the rider's attention and judgment. Always maintain awareness of road conditions and ride safely. Failure to adhere to the guidelines may result in serious accidents.

2. Device Overview

The device consists of the following main components:

• Button: Used for powering on/off, changing light modes, and restarting the device.
• Side-Light: Indicates device status, firmware updates, charging status, and battery level through different colors and flashing patterns.
• Tail Light: A multi-mode tail light that can be controlled by the button to change light modes.
• Radar Module: Built-in radar to monitor moving objects behind the rider.
• Indicator: Provides visual feedback on the device's status.

3. Status LED

4. Tail Light Mode

*Single radar mode: Tail light is off, and only the radar is on normal working status.

5. Radar Detection

• The radar can detect approaching vehicles within a distance of about 140 meters.
• The relative speed of approaching vehicles detected by the radar must be within 10km/h-160km/h (6-99 mph). Note: Radar will not detect vehicles moving at the same speed as you, or vehicles moving away from you.
• The radar beam width is 40° (-20° to 20°) in the horizontal direction.
• Radar can detect up to eight approaching vehicles at most.
• Radar detection cannot be used indoors.

6. In the Box

• Radar Host ×1
• Fixed seat ×1
• Rubber pad ×2
• Rubber band ×2
• Lanyard ×1
• Type-C charging cable ×1

[Image of the contents of the box]

7. Installation Instructions

• Select a suitable position to install the device, ensuring it does not affect riding safety.
• Install the device at an appropriate height on the seat post for optimal detection range.
• The fixed seat should be installed vertically and is compatible with most seat post types and angles.
• Install the device correctly, ensuring it faces backward and is perpendicular to the road.
• Make sure there are no obstructions in front of the device.

[Diagram showing correct installation on a bicycle seat post]

8. Installing the Fixed Seat

• Select an appropriate rubber mat based on your seat post shape and fix it to the back of the fixed seat.
• Place the fixed seat and rubber mat on the seat post.
• Secure with a rubber band.
• Align the card tray on the back of the device with the card slot of the fixed seat and rotate clockwise until the device is locked.
• To prevent the device from falling, the lanyard can be installed together with the device.

[Diagrams illustrating the steps for installing the fixed seat]

9. Device Charging

• Before charging, open the waterproof cover on the USB port and slowly insert the charging cable.
• To prevent metal corrosion, keep the USB interface and surrounding area dry before charging.
• After charging, securely close the USB cover to prevent water ingress or damage.

[Diagram showing the device being charged]

10. Maintenance and Cleaning

• Avoid storing the device in extreme temperature environments for extended periods, as this may cause permanent damage.
• Avoid using organic solvents, chemicals, or repellents, as they may damage device components.
• Avoid violent impacts or rough use, which can shorten the product's lifespan.
• Do not use cloths or materials that may scratch the optical lenses, as scratches can degrade radar detection performance.
• Regular cleaning of mud or dirt will extend the device's lifespan.

11. Product Specifications

*Product parameters are based on laboratory test results. Actual use may be affected by environmental factors.

*BLE and ANT+ wireless protocols are used to connect the device with the iGPSPORT cycling computer and app.

12. Safety and Product Information Notices

Warning

If the radar device does not send detection information to the display device, it is recommended to stop riding and check the device in a safe place. Turn off both devices, then try to reconnect after restarting. The display interface is for illustrative purposes only; the specific display form is subject to the actual device.

1. Riding Warning

• Always maintain your best sense of attention and judgment for safe riding.
• Ensure your bicycle and all components are well-maintained and correctly installed.

2. Distraction Warning

• Proper use can enhance your riding experience. Improper use may lead to distraction, severe injury, or death.
• Quickly check information and remain aware of your surroundings. Do not stare at the screen or become distracted.
• Excessive focus on the screen may cause you to overlook obstacles or dangers. Use this device responsibly and prudently.

3. Battery Warning

• The product uses a rechargeable lithium battery.
• Failure to follow instructions may shorten battery life, damage the device, cause fire, chemical burns, electrolyte leakage, or injury.
• Do not disassemble, modify, puncture, or violently damage the device or battery.
• Do not expose the device or battery to fire, explosion, or other hazards.
• Do not place or store the device in high-temperature environments (e.g., dryer, car in direct sunlight).
• Do not immerse the battery in water or other liquids.

13. Contact Us

• Website: www.igpsport.cn
• Company: Wuhan Qiwu Technology Co., Ltd.
• Address: 3/F Creative Workshop, No.04 District D Creative World, No.16 West Yezhihu Road, Hongshan District, Wuhan, Hubei, China.
• Phone: (86)027-87835568
• Email: service@igpsport.com

Disclaimer

This user manual is for reference only. If there are discrepancies between the device and the manual, the device specifications prevail. Wuhan Qiwu Technology Co., Ltd. reserves the right to change or improve its products and this manual without prior notice.

Copyright belongs to Wuhan Qiwu Technology Co., Ltd.

CE Warning

• CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
• The product shall only be connected to a USB-C interface of version USB2.0.
• Operation temperature: -20~60°C.

Wuhan Qiwu Technology Co., Ltd. declares that this SMART RADAR TAILLIGHT complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. This information is presented in local languages for user understanding. Illustrations, pictograms, and international abbreviations may aid comprehension.

EU Declaration of Conformity

Wuhan Qiwu Technology Co.,Ltd. declares that this SMART RADAR TAILLIGHT is in compliance with Directive 2014/53/EU and can be used in Europe without restriction.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.