New Bee BH58 User Manual
Product Overview
This document provides instructions for the New Bee BH58 Bluetooth headset.
Diagram
Diagram showing the headset with labels for Microphone ?, MFB (Multi-Function Button), Volume Up ➕, Volume Down ➖, charging indicator ⚡, and Bluetooth indicator ?.
Power On/Off
| Action | LED Indicator | Voice Prompt |
|---|---|---|
| Push the button to the top, press and hold for 3 seconds (enters cellphone pairing mode). | The blue light flashes for 3 seconds, then the red light and blue light flash alternately. | Power On ? |
| Push the button to the middle position (enters Bluetooth transmitter pairing mode). | The blue light flashes for 3 seconds, then the red light and green light flash alternately. | Power On ? |
| Push the button to the bottom, the headset will be turned off. | LED light goes out. | Power Off ? |
How to Connect The Bluetooth Transmitter
Step 1: Push up the power button to turn on the headset. The headset indicator light is blue and flashes for about 3 seconds, then turns into red and green light flashing alternately.
Step 2: Plug the Bluetooth transmitter into the device. The indicator light of the Bluetooth transmitter is blue and flashes for about 3 seconds, then turns into red and blue light flashing alternately. You will hear the "Pairing" ?️ voice prompt, and the Bluetooth transmitter will automatically search and connect to the headset.
Step 3: After the connection is successful, the headset indicator light flashes blue every 30 seconds, and the indicator light of the Bluetooth transmitter is solid blue. When there is a connection record, the Bluetooth transmitter will automatically reconnect to the headset after powering on.
Diagram showing the headset connecting to a computer via a USB Bluetooth transmitter.
Note: If the device does not work normally after connection, check sound settings. Open 'sound settings', find 'Playback and Recording Devices', and select 'BTD-Q2'.
How to Connect Your Cellphone
Step 1: Push the power button up to the top, press and hold for 3 seconds, then release. The blue light flashes for 3 seconds, then the red and blue lights flash alternately. You will hear the "Pairing" ?️ voice prompt.
Diagram showing the headset connecting to a smartphone via Bluetooth ?, with a connection range indicator (<1m / 3.3ft).
Step 2: Turn on the Bluetooth of your cellphone, find "BH58" and click to connect. When you hear the 'connected' ?️ voice prompt, the connection is successful.
Note: If a connection record exists, the headset will automatically connect to the cellphone after powering on. If both headset and transmitter have records, the transmitter connects first.
Call Functions
| Function | Action |
|---|---|
| Answer Call | Click once ? |
| Hang up | Click once during a call ? |
| Reject a call | Press and hold for 2 seconds during a call ❌ |
| Redial last phone number | Press and hold for 2 seconds when not in a call ? |
| Voice assistant | Double-click when not in a call ?️ |
| Microphone mute | Click once to turn on/off during a call ? |
Volume Control / Music Control
| Control | Action |
|---|---|
| Volume Up ➕ | Click once |
| Next Track ⏭️ | Press and hold for 2 seconds |
| Volume Down ➖ | Click once |
| Previous Track ⏮️ | Press and hold for 2 seconds |
Restore Factory Settings
Press and hold the Volume + ➕ and MFB buttons simultaneously for 6 seconds. The headset will re-enter pairing mode and you will hear the voice prompt "dudu".
Charging Indications
Diagram showing the headset connected to a charger, with indicator lights.
- Charging: Red light ? stays on.
- Fully Charged: Blue light ? stays on.
- Charging time: Approximately 2 hours ⏰.
Common Problems
- Disconnection: Low battery may cause disconnection. Charge the headset promptly.
- Headset not turning on: Try charging it first, then turn it on after it's fully charged.
- No initial charging light: If the battery is depleted or has not been used for a long time, there may be no signal lights at the beginning of charging. The indicator will light up red normally after a few minutes.
- No Sound from headset:
- Ensure the headset is correctly connected to the electronic device.
- Ensure the effective distance between the headset and device is within 10 meters (33 feet).
- Verify that this Bluetooth device is selected for music playback.
- Ensure your electronic device is in a strong signal area without external interference.
- Check if your electronic device is connected to other Bluetooth devices.
- Headset model not searchable:
- Ensure the headset is in the desired pairing mode (Phone/Bluetooth Transmitter).
- There might be a program error. Reset the headset by pressing and holding the MFB and Volume "+" buttons for 6 seconds while powered on.
- No sound during a call:
- Ensure your headset and device are successfully connected.
- Make sure the call is selected in the Bluetooth device's status.
Safety Notes
- Use original accessories only. Using non-original accessories may lead to reduced performance, headset damage, or short circuits, which are not covered by warranty.
- Disassembling the headset personally may cause damage and is not covered by warranty.
- Do not use the product in a dusty environment.
- Clean the headset with a clean, soft, and dry cloth.
- Avoid extreme environmental conditions. The normal operating temperature is -10°C to 45°C (-4°F to 113°F).
Customer Feedback
Happy? ? Thank you for choosing New Bee products! If you are satisfied, please share your experience with friends. We also engage with fans for feedback and offer free pre-release products. Follow us on:
f Facebook: NewBeeBrand
? Website: https://www.anewbee.com
Not Happy? ? If you have any questions or concerns, please contact us:
? E-mail: support@anewbee.com
? Tel: (USA) 1-626-701-7623 | (UK) 07845854035
Address: 3rd Fl, Bldg E, Guanghao Ind., No. 23, Yunfeng Rd, Dalang St., Longhua Dist., Shenzhen City, Guangdong Prov., China
anewbee.com
