MILLER CompassX Fluid Head User Manual

User Manual for MILLER models including: MILLER, CompassX, Fluid Head, 1090 Compassx 2 Fluid Head, 1092 Compassx 6 Fluid Head, 1093 Compassx 8 Fluid Head, 1096 Compassx 10 Fluid Head, 1097 Compassx 14 Fluid Head

Fluid Head - Lensrentals.com

Feb 21, 2021 —

3 Thank you for purchasing the Compassx Fluid Head. The Compass x Fluid Head has been designed to suit a wide range of cameras, lenses and accessories as demanded by professional users. The robust design and construction of the Compassx Fluid Head offers maximum stability and durability and includes a precision

File Info : application/pdf, 12 Pages, 4.97MB

index.2

Fluid Head
OPERATOR'S MANUAL
1090 Compassx 2 Fluid Head 1092 Compassx 6 Fluid Head 1093 Compassx 8 Fluid Head 1096 Compassx 10 Fluid Head 1097 Compassx 14 Fluid Head

Features and Controls

Spare Camera Screws Tilt Lock

Platform CB PLUS Selector

Safety Release Lever Slide Lock Lever

Tilt Drag Ring M10 Stud

Counterbalance Selector Ring

LED Button

Handle Clamp

Pan Drag Ring

Accessory Mounts

Ball Clamp
Fig. 1
2

Pan Lock
Fig. 2

Introduction

Safety Instructions

Thank you for purchasing the Compassx Fluid Head. The Compassx Fluid Head has been designed to suit a wide range of cameras, lenses and accessories as demanded by professional users.
The robust design and construction of the Compassx Fluid Head offers maximum stability and durability and includes a precision drag plate system in the pan and tilt assembly to deliver true fluid drag performance over the entire temperature and payload range.
The fluid drag and the counterbalance system were designed to provide excellent control and repeatability and offer progressive equal increments of drag and torque through the unique radial ring design.
The Compassx Fluid Head will give best performance when used on a wide range of Miller tripods, including SOLO, Toggle, Sprinter II and HD Tripods (depending on bowl size). This will ensure maximum system stability to suit any professional setup. The Compassx Fluid Head will suit most industry standard 75mm and 100mm tripods as well, please refer to manufactures' manual for mounting details.

Please use this manual to familiarise yourself with the operation of the Compassx Fluid Head and observe these instructions to prevent any damage to your equipment. Ensure that all equipment is operating correctly and free from defects and damage, also please ensure that the tripod is steady, secure and that the bowl is approximately horizontal when attaching the camera. The operator is responsible for the safe operation of this piece of equipment.
· Do not exceed the maximum payload capacity of the Fluid Head.
· Do not leave the camera unattended on the Fluid Head.
· Do not release the SLIDE LOCK LEVER whilst the camera is at an angle.
· Do not adjust the tripod whilst the camera is attached to the Fluid Head.
· Ensure PAN HANDLE CLAMP and CLAMP NUT is securely tightened.
· Apply TILT LOCK when adding/removing equipment from the camera or when attaching/removing the camera from the Fluid Head.
· Hold camera securely whilst changing Counterbalance, Pan Drag or Tilt Drag settings.
· Hold the camera securely whilst releasing the SAFETY RELEASE LEVER.
· Hold camera securely whilst adjusting the CLAMP NUT to level the Fluid Head.

Operating Instructions

2.Mounting Your Camera
2.1 Remove the CAMERA PLATE by lifting the SAFETY RELEASE LEVER on the PLATFORM (SLIDE LOCK LEVER must be unwound (clockwise)) (Fig. 3a).
2.2 Attach the CAMERA PLATE to the camera1 such that the Centre of Gravity (C of G)2 mark on the camera is approximately in the middle of the camera plate.
2.3 Tighten PAN/TILT LOCKS, mount the CAMERA PLATE to the PLATFORM non-locking side first. The side load lock mechanism will capture camera plate (distinct click sound will be made when CAMERA PLATE is retained). CAMERA PLATE will be able to slide freely (60mm) until SLIDE LOCK LEVER is tightened.
2.4 Untighten TILT LOCK, slide the CAMERA PLATE such that the camera's C of G is directly above the centre axis of the Fluid Head (fig. 3b), camera should be balanced (if not slide camera backward or forward). Once balanced tighten the SLIDE LOCK LEVER (anti-clockwise)3 and tighten TILT LOCK.
If this cannot be achieved then reposition the CAMERA PLATE on the Camera step 2.2.
NOTES:
1 Refer to the camera's owners manual for correct method of attachment to the CAMERA PLATE. Remove the 1/4" screw or 3/8" screw as required.
2 The camera's C of G can be estimated by placing the camera on to a round rod and then shifting it backwards or forwards until a balance point C of G - is achieved. It is recommended to identify this point on the camera as it will be useful in step 2.2.
3 Ensure SLIDE LOCK LEVER is tightened at all times when you are not finding C of G or mounting/dismounting camera.

Slide Lock Lever
Safety Release Lever C of G

Platform Tilt Lock
Pan Lock
Fig. 3a
Centre Axis
Fig. 3b

Operating Instructions
3.Counterbalance Control
The counterbalance system was designed to neutralise the effect of the camera weight when it is tilted. The Compassx Fluid Head offers a 16 position counterbalance system which is operated with the CB SELECTOR RING and the CB PLUS SELECTOR (Fig. 4). With the Compassx systems it is also possible to disengage counterbalance (position zero),
NOTE:
Be careful when disengaging counterbalance as you could damage your equipment with an unwanted tilt drop.
The CB SELECTOR RING and the CB PLUS SELECTOR must be operated when the BASE PLATE is in a horizontal position.
After changing the counterbalance setting it may be necessary to tilt the camera back and forth to ensure that the CB spring has engaged.
3.1 For safety it is generally better to start at a higher counterbalance position (e.g. position 14) and work your way to the correct setting, this is to reduce any chance of unwanted tilt drops (Fig. 4).
3.2 Hold the camera and release the TILT LOCK, then gently tilt the camera from the horizontal position forward then backward and observe its response. If the camera `springs back' to the horizontal position then a lower counterbalance setting is required, use the CB SELECTOR RING to cycle through all even number positions (eight positions including zero).
3.3 Finer adjustments can be made by engaging the CB PLUS SELECTOR (upward direction).
3.4 Correct counterbalance setting has been achieved when the camera does not spring back or drop when pan handle is released.

CB PLUS off CB PLUS on

CB Selector Ring CB PLUS Selector
Fig. 4

Operating Instructions
4.Pan/Tilt Drag Control
The Compassx Fluid Head offers selectable positions of fluid drag in the Pan and Tilt (including zero positions). The settings are equally stepped from lighter drag in position 1 up to heavier drag in position 3 on CX2 and CX6 models and position 5 on CX8, CX10 and CX14 models, the drag plates are completely disengaged in position zero. · Do not pan or tilt the Fluid Head whilst adjusting PAN or
TILT DRAG CONTROL or whilst the PAN and TILT DRAG CONTROL is between settings. · The drag setting can be changed at any tilt or pan angle.
5.Pan/Tilt Lock Control
The Compassx Fluid Head offers high capacity caliper disc brake system to hold the Fluid Head in a fixed pan and/or tilt position. Camera position will not change when applying or releasing the Pan-tilt locks. · Do not pan or tilt the Fluid Head whilst the PAN or the TILT
LOCK is partially applied.
6.Illumination
The Compassx Fluid Head offers illumination of the BUBBLE LEVEL when the low ambient light conditions exist. Illumination can be achieved by pressing the LED BUTTON once. The light will switch off after 10 seconds.
6

Fig. 5

Maintenance
The Compassx Fluid Head offers high quality surface coatings, dust and moisture seals. Miller recommends keeping the Fluid Head clean at all times by using soft brushes and lint free cloth to wipe over the surfaces.
· Do not immerse the Fluid Head in any liquid. · Do not use stiff brushes, abrasives, harsh detergents and
solvents.
Battery Replacement
The Compassx Fluid Head uses a single 11A type - 6 Volt battery for Illumination. Miller recommends the following batteries to provide long life performance GP11A, Duracell MN11 or Vinnic L1016.
1. Using a Phillips Head #1 screw driver, remove the RETAINING SCREW and the BATTERY COVER.
2. Using a small flat screw driver remove the battery. 3. Align the new battery as shown on the back of the
BATTERY DOOR and place into the BATTERY HOUSING, then push down the battery into place. A small flat screw driver may be used to push down the battery into the BATTERY HOUSING. 4. Align the BATTERY DOOR into the body then tighten the screw lightly.
7

Battery Battery Cover
Fig. 6

Specifications

Weight

1090 Compassx 2
2.3kg (5.1lbs)

1092 Compassx 6
2.3kg (5.1bs)

1093 Compassx 8
2.5kg (5.5lbs)

1096 Compassx 10
2.5kg (5.5lbs)

1097 Compassx 14
2.5kg (5.5lbs)

Payload range

0-8kg (0-17.5lbs)

0-12kg (0-26.4lbs)

0-14kg (0-30.9lbs)

Pan-tilt drag Pan range

3 selectable fluid drag positions 3 selectable fluid drag positions 5 selectable fluid drag positions 5 selectable fluid drag positions 5 selectable fluid drag positions

+ 0

360°

Pan-tilt locks Tilt angle

Positive lock calliper brake system
+90°/-75°

Counterbalance Camera platform Sliding range

16 selectable positions (0 +15 position)
Side loading, 60mm balance travel camera plate with 1/4" and 3/8" screws
60mm (2.4")

Height above bowl 167mm (6.6")

16 selectable positions (0 +15 position)
Side loading, 60mm balance travel camera plate with 1/4" and 3/8" screws 60mm (2.4")
167mm (6.6")

16 selectable positions (0 +15 position)
Side loading, 60mm balance travel camera plate with 1/4" and 3/8" screws 60mm (2.4")
150mm (6.0")

Mounting base

75mm (2.9") ball levelling

100mm (3.9") ball levelling

Illuminated controls Bubble Level

Bubble Level

Temperature range Pan handle

-40° to +65°C (-40° to +149°F)
Fixed 390mm (15.4")

Specifications
75mm

CX2

CX6 CX8

Specifications
100mm

CX10

CX14

Storage

Service, Sales and Support

The Compassx Fluid Head can be stored for extended periods; Miller recommends storage in a Miller case and the following:
· Clean the external surfaces. · Keep in a dry place away from direct sunlight. · Loosen off PAN & TILT LOCK.

Spare Parts and Accessories

ITEM Battery Camera screw 3/8" Camera screw 1/4" Serrated washer Pan handle - fixed with clamp Pan handle - telescopic with clamp Accessory mounting block Sliding plate assembly (Euro)* Sliding plate assembly (Mini Euro)* 1/4" screw and pin carriage Camera plate Camera plate (short) Camera plate (long)

ITEM NO. P3798 P0037 P0036
PN12501 679 696
1255 1210X 1206X
493 1205 1209 1207

Warranty
MILLER offers 3 years parts and labour warranty.
Please refer to MILLER Warranty card D3993 for complete details.

Miller Authorised Service Agents must carry out all service and repair work. Failure to observe this requirement may void warranty.
It is advisable to notify Miller or a Miller Authorised Service Agent if a change of performance is observed as a result of dropping or rough usage. For information regarding sales and service of Miller products or for your nearest Miller representative please contact us via our website or at the following:
MILLER CAMERA SUPPORT EQUIPMENT 30 Hotham Parade Artarmon, Sydney, NSW 2064 Australia P +61 2 9439 6377 sales@miller.com.au
MILLER Camera Support (LLC) USA 216 Little Falls Road (Unit 2), Cedar Grove, New Jersey 07009 USA P +1 (973) 857 8300 F +1 (973) 857 8188 sales@millertripods.us
MILLER FLUID HEADS (EUROPE) LTD. 12A, Shepperton Business Park Govett Avenue, Shepperton Middlesex, TW17 8BA United Kingdom P +44 (0) 1932 222 888 sales@millertripods-europe.com
millertripods.com

millertripods.com
MILLER CAMERA SUPPORT EQUIPMENT 30 Hotham Parade Artarmon, Sydney NSW, 2064, Australia Tel: +61 2 9439 6377 Fax: +61 2 9438 2819 Email: sales@miller.com.au
D12728-4

PDFium PDFium