Instruction Manual for RODE models including: CASTER PRO II Podcast Production Studio, CASTER PRO II, Podcast Production Studio, Production Studio, Studio
RØDECaster Duo | Recording and Exporting Audio | RØDE
CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO MULTITRACK GUIDELINES | GARAGEBAND | MAC STEP 1 Connect your RØDECaster Pro II to a computer via the USB 1 port on the back of the unit. You will need to use either the supplied USB-C to USB-C cable or, if your computer only has USB-A inputs, a RØDE SC18 cable. NOTE: The USB 2 port does not support multitrack recording. Ensure you use USB 1. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 2 Open Garageband and start a new empty project. The RØDECaster Pro II multitrack output has 16 channels in total: stereo (L + R) outputs for the main mix, mono outputs for the four combo inputs, and stereo outputs for the Bluetooth channel, SMART pad audio, and the three USB channels. The audio channels on the RØDECaster Pro II are sent to the multitrack output as follows: Device 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Source Main Mix Output (L) Main Mix output (R) Combo 1 Combo 2 Combo 3 Combo 4 Bluetooth (L) Bluetooth (R) SMART Pads (L) SMART Pads (R) USB Main (L) USB Main (R) USB Chat (L) USB Chat (R) USB 2 (L) USB 2 (R) Generally, you should create a single track for each stereo or mono audio input, giving you a total of 10 tracks if you are using all inputs. In this walkthrough, the session will include all available channels to demonstrate how to set up each one, but you only need to set up the channels you are using. NOTE: The multitrack output configuration is always the same, regardless of how you have your mixer set up. For example, if you have combo input 2 assigned to fader 6 on your mixer, it will still appear on input 4 in your DAW. Also, if you do not have an audio input allocated to a fader on the mixer, it will not pass through to the multitrack output, so it's a good idea you have your mixer configured how you will be using it for recording before setting up the session in your DAW. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 3 Select `Audio' as your first track type and click `Create'. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 4 Navigate to Preferences within the settings by going to `Garageband' > `Preferences'. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 5 Within the Preferences settings, go to Audio/MIDI and select `RØDECaster Pro II Main' as your Input and Output Device. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 6 Rename your first track to `Stereo Mix' by double clicking on the track name. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 7 Set the input for this track to `1-2 (RØDECaster Pro II Main)'. Set it to stereo by clicking the double circles to the left of the input selector on the channel strip. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 8 Create a new track by going to `Track' > `New Track' in the menu bar. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 9 Select `Audio' as your new track type and click `Create'. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 10 Rename your new track to `Mic 1'. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 11 Change this track input to `3 (RØDECaster Pro II Main)' from the input list. The audio from combo input 1 will now be routed to this track. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 12 Create another track and rename to `Mic 2'. Ensure it is set to mono, then select `4 (RØDECaster Pro II Main)' from the input list. The audio from combo input 2 will now be routed to this track. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 13 Create another track and rename to `Mic 3'. Ensure it is set to mono, then select `5 (RØDECaster Pro II Main)' from the input list. The audio from combo input 3 will now be routed to this track. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 14 Create another track and rename to `Mic 4'. Ensure it is set to mono, then select `6 (RØDECaster Pro II Main)' from the input list. The audio from combo input 4 will now be routed to this track. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 15 Create another track and rename to `Bluetooth'. Ensure it is set to stereo, then select `7-8 (RØDECaster Pro II Main)' from the input list. The audio from the Bluetooth input will now be routed to this track. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 16 Create another track and rename to `SMART Pads'. Ensure it is set to stereo, then select `9-10 (RØDECaster Pro II Main)' from the input list. The audio from the SMART pads will now be routed to this track. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 17 Create another track and rename to `USB Main'. Ensure it is set to stereo, then select '11-12 (RØDECaster Pro II Main)' from the input list. The audio from the USB Main channel will now be routed to this track. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 18 Create another track and rename to `USB Chat'. Ensure it is set to stereo, then select '13-14 (RØDECaster Pro II Main)' from the input list. The audio from the USB Chat channel will now be routed to this track. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 19 Create another track and rename to `USB Secondary'. Ensure it is set to stereo, then select '15-16 (RØDECaster Pro II Main)' from the input list. The audio from the USB Secondary channel will now be routed to this track. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 20 To move forward, you will need to activate record enable in the settings. Go to `Track' > `Configure Track Header' in the menu bar. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 21 In the pop-up menu, there is a section for enabling certain buttons in the track header. Ensure that `Record Enable' is ticked. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 22 Ensure that the tracks that you would like to record are "record enabled" by clicking on the record button in each track header so they flash red. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 23 Go to the USB multitrack settings page on your RØDECaster Pro II (settings > `Outputs' > `Multitrack' > `USB') and select either `pre-fader' or `post-fader' mode. In pre-fader mode, all audio sources will be sent to the multitrack output at unity gain, regardless of the fader positions. You can also choose to bypass any processing you have on your channels. This mode is ideal if you want to capture a clean recording for editing in post-production. In post-fader mode, all processing, channel effects and fader positions will be included in the multitrack output. This is ideal if you want to do all of your mixing and processing on the RØDECaster Pro II. NOTE: Any effects triggered by the SMART pads will appear on the stereo mix but not the individual audio channel on the multitrack output. PRO TIP: When recording in post-fader mode, it's a good idea to also record a "clean" pre-fader multitrack output. MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIO STEP 24 Hit record when you're ready! MULTITRACK GUIDELINES | GARAGEBAND CASTER PRO INTEGRATED AUDIO PRODUCTION STUDIOAdobe PDF Library 16.0.7 Adobe InDesign 17.3 (Macintosh)