Instructions for RigExpert models including: ZeroII Vector Antenna Analyzer, ZeroII, Vector Antenna Analyzer, Antenna Analyzer, Analyzer

Sichkarenko Sergey

ZeroII Vector Antenna Analyzer - RigExpert

2 giu 2023 — Short communication interfaces description. The ZeroII in measurement mode supports communication with the host controller via SPI, I2C, UART. I2C interface use ...

UserManual-ZEROII-English

Support

Product data sheet

RIGEXPERT - ZERO II - ANTENNA ANALYZER KIT - HardSoft Products

• Google Docs
• Google Drive
• Download [pdf]
• Download Optimized



File Info : application/pdf, 3 Pages, 765.93KB

Document Document

ZeroII Vector Antenna Analyzer
Short communication interfaces description.
The ZeroII in measurement mode supports communication with the host controller via SPI, I2C, UART. I2C interface use 7-bit slave address 0x5B. The firmware is updated via the USB interface using the RigExpert Flash Tool utility. Commands supported by SPI, I2C, UART interfaces: ZEROII_GET_STATUS (0x5A) ­ ask for the ZeroII status. (Except SPI - you can read the status after setting CS low without prompting). Possible answers:
ZEROII_STATUS_BUSY_USB (0x01) ­ the device is busy with a task for the USB interface; ZEROII_STATUS_BUSY_SPI (0x02) ­ the device is busy with a task for the SPI interface; ZEROII_STATUS_BUSY_I2C (0x03) ­ the device is busy with a task for the I2C interface; ZEROII_STATUS_BUSY_UART (0x04) ­ the device is busy with a task for the UART interface; ZEROII_STATUS_IDLE (0x05) ­ the device is idle, ready for new tasks; ZEROII_STATUS_READY (0x06) ­ measurement results are ready; ZEROII_STATUS_ERROR (0x07) ­ an error occurred while executing the task; Example request: [(uint8_t)CMD, (uint8_t)CRC *1, (uint8_t)INV_CRC *1] 0x5A, 0x81, 0x7E Response (immediate):
[(uint8_t)Status = IDLE, (uint8_t)CRC *1, (uint8_t)INV_CRC *1]
0x05, 0x1B, 0xE4
ZEROII_SET_SYSTEM_Z0 (0xF2) ­ set the system impedance value (Z0). The default is 50 ohms. Example request:
[(uint8_t)CMD, (uint32_t)Z0=50000 mOhm, (uint8_t)CRC *1, (uint8_t)INV_CRC *1]
0xF2, 0x50, 0xC3, 0x00, 0x00, 0x01, 0xFE Response: NONE
ZEROII_GET_SYSTEM_Z0 (0xC4) ­ get the system impedance value (Z0). Example request: [(uint8_t)CMD, (uint8_t)CRC *1, (uint8_t)INV_CRC *1] 0xC4, 0x52, 0xAD Response (immediate):
[(uint32_t)Z0=50000 mOhm, (uint8_t)CRC *2, (uint8_t)INV_CRC *1]
0x50, 0xC3, 0x00, 0x00, 0xCC, 0x33

ZEROII_SET_FQ_GET_RX (0x6D) ­ set the measurement frequency, get the results as R (resistance), X (reactance). Example request: [(uint8_t)CMD, (uint32_t)FQ=14 720 000, (uint8_t)CRC *1, (uint8_t)INV_CRC *1] 0x6D, 0x00, 0x9C, 0xE0, 0x00, 0x48, 0xB7 Response (delayed *3):
[(float)R=50.1416, (float)X=0.314159, (uint8_t)CRC *2, (uint8_t)INV_CRC *1]
0xFD, 0x90, 0x48, 0x42, 0x7A, 0xD9, 0xA0, 0x3E, 0x88, 0x77
ZEROII_SET_FQ_GET_RXSWRRL (0xA3) ­ set measurement frequency, get results as R (resistance), X (reactance), SWR (standing wave ratio), RL (return loss).
Example request: [(uint8_t)CMD, (uint32_t)FQ=14 720 000, (uint8_t)CRC *1, (uint8_t)INV_CRC *1] 0xA3, 0x00, 0x9C, 0xE0, 0x00, 0x45, 0xBA Response (delayed *3):
[(float)R=50.1416, (float)X=0.314159, (float)SWR=1.03742, (float)RL=34.5816, (uint8_t)CRC *2, (uint8_t)INV_CRC *1]
0xFD, 0x90, 0x48, 0x42, 0x7A, 0xD9, 0xA0, 0x3E, 0x2E, 0xCA, 0x84, 0x3F, 0x8F, 0x53, 0x0A, 0x42, 0x38, 0xC7
ZEROII_GET_RX_DATA (0x7C) ­ repeat the measurement at the previous frequency, get the results as R (resistance), X (reactance). Example request: [(uint8_t)CMD, (uint8_t)CRC *1, (uint8_t)INV_CRC *1] 0x7C, 0x73, 0x8C Response (delayed *3):
[(float)R=50.1416, (float)X=0.314159, (uint8_t)CRC *2, (uint8_t)INV_CRC *1]
0xFD, 0x90, 0x48, 0x42, 0x7A, 0xD9, 0xA0, 0x3E, 0x88, 0x77
ZEROII_GET_RX_SWR_RL (0x9A) ­ repeat the measurement at the previous frequency, get the results as R (resistance), X (reactance), SWR (standing wave ratio), RL (return loss).
Example request: [(uint8_t)CMD, (uint8_t)CRC *1, (uint8_t)INV_CRC *1] 0x9A, 0xCF, 0x30 Response (delayed *3):
[(float)R=50.1416, (float)X=0.314159, (float)SWR=1.03742, (float)RL=34.5816, (uint8_t)CRC *2, (uint8_t)INV_CRC *1]
0xFD, 0x90, 0x48, 0x42, 0x7A, 0xD9, 0xA0, 0x3E, 0x2E, 0xCA, 0x84, 0x3F, 0x8F, 0x53, 0x0A, 0x42, 0x38, 0xC7

ZEROII_GET_FW_VERSION (0xE5) ­ ask the current firmware version, hardware revision, serial number of the device. Example request: [(uint8_t)CMD, (uint8_t)CRC *1, (uint8_t)INV_CRC *1] 0xE5, 0xB5, 0x4A Response (immediate):
[(uint8_t)MAJOR_VER = 1, (uint8_t)MINOR_VER = 1, (uint8_t)HW_REV = 1, (uint32_t)SN = 400107968, (uint8_t)CRC *2, (uint8_t)INV_CRC *1]
0x01, 0x01, 0x01, 0xC0, 0x29, 0xD9, 0x17, 0x25, 0xDA
*1 ­ used for UART only (INV_CRC = CRC ^ 0xFF). *2 ­ used for SPI and UART. *3 ­ before receiving delayed response you need at least once ask for STATUS and get ZEROII_STATUS_READY. Until the measurement is completed, STATUS will correspond to ZEROII_STATUS_BUSY_x.