QSFPTEK - Trusted Transceivers, Optical Network Solution Partner
User Guide for QSFPTEK models including: S5300-16S8TS4X, S5300-16S8TS4X 16-Port Gigabit Ethernet L2 Plus Switch, 16-Port Gigabit Ethernet L2 Plus Switch, Gigabit Ethernet L2 Plus Switch, Ethernet L2 Plus Switch, L2 Plus Switch, Switch
File Info : application/pdf, 12 Pages, 741.53KB
DocumentDocumentS5300-16S8TS4X Quick Start Guide V2.0 16-Port Gigabit Ethernet L2+ Switch 16x 1G SFP, with 8x 1G RJ45/SFP Combo, 4x 10G SFP+ Uplinks, Support Stacking www.qsfptek.com V2.0 0 1 / 12 Introduction The S5300-16S8TS4X is a managed gigabit access layer switch with 16x 1G SFP, 8x 1G RJ45/SFP combo, 4x 10G SFP+ uplink ports, supports stacking of up to 2 switches. It has built-in two intelligent fans, which can automatically adjust the fan speed to save on usage costs. The switch can be easily controlled and managed through both CLI and WEB interfaces, allowing for real-time monitoring and improved management efficiency. This makes the S5300-16S8TS4X an ideal choice for SMBs, enterprise networks, and campus networks. We appreciate your decision to select S5300-16S8TS4X. This manual is intended to help you become acquainted with the switch design and provide instructions for implementing the switches into your network. Accessories www.qsfptek.com V2.0 0 2 / 12 Hardware Overview Front Panel Ports Ports Combo Port SFP Port SFP+ Port CON Port Front Panel LEDs Description RJ45/SFP Combo port SFP ports for 1G connection SFP+ ports for 10G connection A baud rate of 9600bps, RJ45 port LEDS SFP Status / SFP+ / SYS LED / PWR LED / Description On Off On Off / / The link on the port is normal. The link on the port is failed. The link on the port is normal. The link on the port is failed. If the SYS indicator flickers, the system works normally. If the PWR indicator is always on, the device is powered on. www.qsfptek.com V2.0 0 3 / 12 Back Panel Abbrev / / POWER Name Grounding column Power switch AC power supply Description The grounding must be fine ON means the power is switched on, while OFF means the power is cut off Input voltage AC100-240V Installation Requirements Tools Preparation Screwdriver Static-proof wristband Bolt Ethernet cable Other Ethernet terminal devices Control terminal Safety Principles Keep dustless and clean during or after the installation. Put the cover in a safe place. Put tools in the right place where they are not easily falling down. Put on relatively tight clothes, fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box. Put on protective glasses if the environment may cause damage to your eyes. Avoid incorrect operations that may cause damage to humans or devices. www.qsfptek.com V2.0 0 4 / 12 Site Environment Make sure that the workshop is well-ventilated, the heat of electrical devices is welldischarged Avoid damaging devices by following the electrostatic discharge prevention procedure. S5300-16S8TS4X Hardware Installation Manual Put the machine box in a place where cool air can blow off the heat inside the machine box. Make sure the machine box is sealed. Mounting the Switch Connecting the Power Plug the AC power cord to the switch power port on the back rear. Connect the other end of the power cord to an AC power source equipment. www.qsfptek.com V2.0 0 5 / 12 Connecting the RJ45 Ports Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc. Connect the other end of the Ethernet cable to the switch RJ45 port. www.qsfptek.com V2.0 0 6 / 12 Connecting the SFP Port Insert the SFP module into the SFP port. Plug a fiber patch cable into the SFP transceiver. Connect the other end of the fiber to the device that you want to realize data communication. www.qsfptek.com V2.0 0 7 / 12 Connecting the SFP+ Port Insert the SFP+ module into the SFP+ port. Plug a fiber patch cable into the SFP+ transceiver. Connect the other end of the fiber to the device that you want to realize data communication. www.qsfptek.com V2.0 0 8 / 12 Connecting the Management Ports Connecting the Console Port Prepare a console cable. Insert the RJ45 connector of the console cable into the console port on the switch. Connect the DB9 female connector on the other end of the console cable to the serial port on the computer host. Configuring the Switch Configuring the Switch Using the Web-based Interface Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser. www.qsfptek.com V2.0 0 9 / 12 Step 2: Set the IP address of the computer to 192.168.0.x (where "x" is any number from 2 to 254) and the subnet mask to 255.255.255.0. Step 3: Open a web browser and type http://192.168.0.2 in the address bar. Enter the default username and password (admin/admin). Step 4: Click sign-in to access the web-based configuration page. www.qsfptek.com V2.0 0 10 / 12 Configuring the Switch Using the Console Port Step 1: Use the console cable to directly connect the switch console port to your computer. Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer. Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow control. Step 4: Enter the default username and password (admin/admin). Troubleshooting Hardware Fault Analysis 1. Power and cooling systems--power and fan 2. Port, cable and connection--ports on the front panel of the switch and the cables connecting these ports Faults Relative to Power and Cooling System Do the following checkups to help remove the fault: 1. When the power on-off is at the "ON" location, check whether the fan works normally. If the fan www.qsfptek.com V2.0 0 11 / 12 does not work well, check the fan. 2. If the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3 "Requirements for Common Locations". 3. If the switch cannot be started and the PWR indicator is off, check the power. Faults Relative to Port, Cable and Connection Do the following checkups to help remove the fault: 1. If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal. 2. If the power on-off is at the "ON" location, check the power source and the power cable. 3. If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits, no sum check bit, one stop bit and no traffic control. Support and Other Resources Contact us Customer Success Email https://www.qsfptek.com/company/contact-us.html https://www.qsfptek.com/resources/customer-success-stories support@qsfptek.com Product Warranty S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. You are eligible to apply for a return within 14 days and exchange within 90 days of receiving them. For more details about applying qualifications, please live chat or email sales@qsfptek.com for support. 5 Year Warranty 14-day Return Window www.qsfptek.com V2.0 0 12 / 12