User Guide for Aim models including: Solo 2, Solo 2 DL, EVO4S, ECULog, Solo 2Solo 2 DL Bike Engine Control Unit, Solo 2Solo 2 DL, Bike Engine Control Unit, Engine Control Unit, Control Unit, Unit
• Aprilia RSV4 2017-2018 • Aprilia RSV4 1100 2019-2020 • Aprilia Tuono V4 2017-2020 Warning: for these models/years AiM recommends not to remove the stock dash.Doing so will disable some of the bike functions or safety controls.
Aprilia dedicated cable for Solo 2 DL, ECULog and EVO4S
AiM User Guide Solo 2/Solo 2 DL, EVO4S and ECULog kit for Aprilia RSV4, RSV4 1100 and Tuono V4 2017-2020 Release 1.04 1 Models and years This manual explains how to connect, EVO4S Solo 2 DL and ECULog to the bike engine control unit (ECU). Compatible models and years are: · Aprilia RSV4 · Aprilia RSV4 1100 · Aprilia Tuono V4 2017-2018 2019-2020 2017-2020 Warning: for these models/years AiM recommends not to remove the stock dash. Doing so will disable some of the bike functions or safety controls. AiM Tech Srl will not be held responsible for any consequence that may result from the replacement of the original instrumentation cluster. 1 2 Kit content and part numbers AiM developed a specific installation bracket for Solo2/Solo 2 DL that fits Aprilia RSV4 1100 and a CAN connection cable to the ECU for Solo 2 DL, EVO4S and ECULog that fits Aprilia RSV4, Aprilia RSV4 1100 and Aprilia Tuono V4 bikes. 2.1 Bracket for Solo 2/Solo 2 DL (Aprilia RSV4 1100 only) Part number of Solo 2 / Solo 2 DL bracket kit for Aprilia RSV4 1100 only shown below is: X40KSARSV40. The kit includes: · 1 bracket (1) · 1 Allen screw with rounded head M8x45mm (2) · 2 Allen screws with flat head M4x10mm (3) · 1 toothed washer (4) · 1 rubber dowel (5) 2 2.2 AiM CAN cable for Solo 2 DL, EVO4S and ECULog CAN connection cable for Solo 2 DL, EVO4S and ECULog for Aprilia RSV4, Aprilia RSV4 1100 and Aprilia Tuono V4 is shown below. Its part number is: V02589090. The image below shows the cable constructive scheme. 2.3 AiM kit for Solo 2 DL (CAN cable + Bracket) Please note: connection cable for Solo 2 DL and installation bracket for Aprilia RSV4 1100 can also be bought together with part number: V02589090CS 3 3 Solo 2 DL, EVO4S and ECULog connection Aprilia RSV4 communication protocol is CAN based; it can be reached through the dedicated 8 pins connector for V4-MP module connection, placed on the bike left side. 4 4 Configuration with RaceStudio 3 Before connecting the ECU to AiM device set this last one up using AiM RaceStudio 3 software. The parameters to select in the device configuration are: · ECU Manufacturer: Aprilia · ECU Model: RSV4_APRC_V4MP (RaceStudio 3 only) After this first selection, uncheck the "120 Ohm resistor" box and check the "Silent mode on CAN Bus" under the "ECU Stream" tab: 5 5 "Aprilia RSV4_APRC_V4MP" protocol Channels received by AiM devices configured with "Aprilia RSV4_APRC_V4MP" protocol are: CHANNEL NAME RSV4 RPM RSV4 GEAR RSV4 BK SPEED RSV4 WH SPD F RSV4 WH SPD R RSV4 ACC LONG RSV4 ACC LAT RSV4 ROLL RATE RSV4 YAW RATE RSV4 ENG TEMP RSV4 Brake press RSV4 Baro RSV4 MAP2 Target RSV4 MAP1 Target RSV4 MAP2 RSV4 MAP1 RSV4 Advance V4MP Lean angle RSV4 Pitch angle RSV4 Roll angle RSV4 PFANGCOR 1 FUNCTION RPM Engaged gear Bike speed Front wheel speed Rear wheel speed Longitudinal acceleration Lateral acceleration Roll rate Yaw rate Engine coolant temperature Brake pressure Barometric pressure Manifold air pressure 2 target Manifold air pressure 1 target Manifold air pressure 2 Manifold air pressure 1 Ignition advance Lean angle Pitch angle Roll angle - 6 RSV4 PFANGCOR 2 V4MP Throttle RSV4 THRT HAND RSV4 TPS1 RSV4 TPS2 V4MP Torque end V4MP Inj Time RSV4 Odometer RSV4 V BATT RSV4 Pit speed RSV4 ATC RSV4 AWC RSV4 ALC RSV4 AQS On RSV4 Pit on RSV4 Pit active V4MP ATC level V4MP Speed V4MP ABS int V4MP Slip RSV4 Sistfas RSV4 Cntlostsync Cruise selector RSV4 ALC INT RSV4 SEL MAP RSV4 WARNING RSV4 Urg serv Throttle position Hand throttle position Throttle position sensor 1 Throttle position sensor 2 Torque reduction Injection time Odometer Battery voltage Pit limiter speed ATC Aprilia traction control AWC Aprilia wheel control ALC Aprilia launch control AQS on Aprilia quick shift on Pit limiter on Pit limiter activated ATC level Aprilia traction control level Bike speed ABS intervention Tyre slip Lost syncs counter Cruise selector Aprilia launch control intervention Map selector Warning light Urgent service lamp 7 RSV4 MIL RSV4 TC INT RSV4 FUEL LOW Set confirm RSV4 Tipover TC menu set butt RSV4 SIDE STAND RSV4 ABS Malfunctioning indicator lamp Traction control intervention Low fuel level Selection key confirmation Tip over sensor Traction Control setting key Side stand led ABS Please note: throttle position may or may not come across in the CAN data stream due to an update by the manufacturer. Technical note: not all data channels outlined in the ECU template are validated for each manufacturer model or variant; some of the outlined channels are model and year specific and therefore may not be applicable. 8Laura MaLu Adobe PDF Library 24.3.212