Instructions for iMaihom models including: APSBD0000342 100W Motion Sensor Led Security Light With Plug, APSBD0000342, 100W Motion Sensor Led Security Light With Plug, Sensor Led Security Light With Plug, Security Light With Plug, Light With Plug, With Plug, Plug
iMaihom 100W Motion Sensor LED Security Light with Plug, 9000LM Flood Lights Outdoor Plug in, 6500K Exterior Floodlight, IP65 Waterproof,3 Head Adjustable Motion Detector Light for Yard(1Pack)
TEST D2D H L M Sensor Function Instructions OPERATION INSTRUCTIONS Knob æ is to start test mode and set the light timer 1 from 10 seconds to 10 minutes (counterclockwise). Knob ç is to set the ambient illuminance detection value(80-2000Lux). When the illuminance is lower than the set Lux value, the light's motion sensor TEST mode and D2D mode will start to work. Knob between "A", both modes start working at sunset/dusk. Knob between "B", both modes start working at night. Note: The time may be earlier or later due to weather, altitude, or season. Knobè is to start D2D mode and set the motion detection distance in motion sensor mode. "L" Detection distance is 19.7~26.2ft. "M" Detection distance is 26.2~39.3ft. "H"Detection distance is 39.3~72ft. 2 3 D2D H L M A B 1. Test Mode 1) What is test mode? The floodlight turns on for 5 seconds when it detects a person and then turns off no matter the day or night. In this mode you can adjust the sensor's angles and detection distance to achieve your perfect sensing range. 2) How to set test mode? TEST D2D H L M Step 1: Turn knob æ to the "TEST" position as shown on the left. Step 2: Turn knob è to the range as shown on the left to set the detection distance (Knob ç can be pointed to any position.). Note: When using other modes, be sure to exit the test mode (Turn Knob æ counterclockwise away from the "TEST" position.). 2. Motion Sensor Mode 1) What is motion sensor mode? The floodlight will turn on when detecting a person, car, or animal, and stay on for 10S-10Min after leaving. Then turn off. Note: Through setting the lux value (knob 2), you can freely choose the motion sensor mode work time--sunset, dusk, night, or other period you like. 2) How to set the motion sensor mode? Step 1: Turn knob æ to the range as shown on the left to set the light timer (10s-10mins). Do not point to the "TEST" position. TEST D2D H Step 2: Turn knob ç to the A, B range as shown on the left to adjust the light-up time at sunset, dusk, night L M A B or other period you like. Step 3: Turn knob è to the range as shown on the left to set the detection distance. 1 OPERATION INSTRUCTIONS Examples: TEST D2D H If you want the floodlight to turn on at dusk for 15 seconds when it detects a person, and in maximum L M detection distance, then turn off after leaving. You can set the three knobs as shown on the left. Examples: TEST D2D H If you want the floodlight to turn on at night for 10 minutes when it detects a person, and in medium L M detection distance, then turn off after leaving. You can set the three knobs as shown on the left. 3. D2D (Dusk to Dawn) Mode 1) What is D2D mode? The floodlight will automatically turn on at dusk and turn off at dawn. In this mode, the motion sensor function is not valid. 2) How to set D2D mode? TEST D2D H L M A B Step 1: Turn Knob æ counterclockwise away from the "TEST" position to exit the test mode as shown on the left. Step 2: Turn knob ç to the A, B range as shown on the left to adjust the light-up time at sunset, dusk, night or other period you like. Step 3: Turn knob è to the "D2D" position as shown on the left. Examples: TEST D2D H If you want the floodlights turn on at sunset and turn off at sunrise, you can set the three knobs as shown on L M the left. 2Adobe PDF library 15.00 Adobe Illustrator(R) 24.0