Saitake STK-7046 Portable Wireless Joypad User Manual

Installation Steps

I. For NS OLED Console

To attach the joy-cons to the NS OLED Console:

1. Remove the existing joy-cons from both sides of the console.
2. Insert the provided "spacer" into the slide rails on both sides of the console.
3. Align the joy-con with the console's rail and slide it into place until it clicks.
4. To remove, gently lift the top of the "spacer" and then pull out the joy-con.

Diagram shows joy-cons being attached to an NS OLED console with a spacer.

II. For NS Console

To attach the joy-cons to the NS Console:

1. Hold the controller in place. Push out the console from the bottom.
2. Align the controller track and insert the main unit from the middle of the controller until it is fully inserted.

Diagram shows joy-cons being attached to an NS console.

Disassembly Steps

1. For NS OLED Console

To remove the joy-cons from the NS OLED Console:

1. Hold the controller in place. Push out the console from the bottom.
2. Align the controller track and insert the main unit from the middle of the controller until the main unit is fully inserted into the controller.

Diagram shows joy-cons being removed from an NS OLED console.

Connection Method

To connect the Portable Wireless Joypad to your console:

1. Ensure the console's flight mode is turned off.
2. Navigate to the console's connection interface (refer to console's manual for specific steps).
3. Press and hold the [SYNC] button on the joypad until the four signal lights flash rapidly back and forth. Release the button and wait for a successful connection.

Visuals show the console's connection interface and a pairing screen.

After the initial successful connection, you can wake up the console and reconnect by briefly pressing the [HOME] button.

Troubleshooting Connection Issues:

1. Turn off airplane mode on the console.
2. On the NS console, go to System Settings > Controllers and Sensors > Disconnect Controllers, and remove this controller's information.
3. Follow the initial connection method again to re-pair the controller.

Features

Turbo Function

Basic buttons that can be assigned the Turbo function: A, B, X, Y, L1, L2, R1, R2.

• Manual Turbo: Press the [Turbo] button and a desired base button simultaneously to activate manual Turbo for that button.
• Turn Off Manual Turbo: Press the [Turbo] button and the base button (which has manual Turbo enabled) simultaneously again to turn it off.
• Turn Off All Turbo Functions: Long press the [Turbo] button for 5 seconds. The four signal lights will flash 3 times, indicating all Turbo functions are deactivated.

Turbo Speed Adjustment:

• Slow Speed (5 rounds per second): Press [Turbo] + [↓] button simultaneously. LED 2 flashes during use.
• Medium Speed (10 rounds per second): Press [Turbo] + [→] button simultaneously. LED 2 and LED 3 blink during use.
• Fast Speed (20 rounds per second): Press [Turbo] + [↑] button simultaneously. LED 2, LED 3, and LED 4 blink during use.

Diagrams illustrate button combinations for Turbo speed.

Vibration Function

The controller offers four levels of vibration intensity: none, weak, medium, and strong.

To Adjust Vibration Intensity:

1. Ensure the controller is successfully connected to the console.
2. Press and hold the L1, R1, L2, and R2 buttons simultaneously for approximately 1 second. The controller will vibrate once, indicating successful adjustment. This cycles through the 4 levels of vibration.

Charging Tips

• Low Battery Alert: LED 4 flashes rapidly.
• Charging In Progress: LED 4 flashes slowly.
• Fully Charged: LED 4 is off.

Light Effect Control

Press the [L3] and [+] buttons simultaneously to turn the button lighting effect on or off.

Frequently Asked Questions (FAQ)

Q: How to solve the problem that the controller's joystick will not automatically return to the center when it is stuck at the edge?

A: Try setting the joystick to the center and then pressing down with your thumb while turning the joystick again.

Q: What is the situation when I can't wake up and connect back to the console by pressing the [HOME] button?

A: Ensure the controller and console have made the initial connection. Press the HOME button briefly for about 1 second and release your finger after the signal light comes on; do not keep holding it down.

Q: Is there a way to recover from joystick drift during controller use?

A: Please try the following calibration method: With the controller turned off and placed on a horizontal surface, press the [B], [HOME], and [-] buttons simultaneously. The signal lights will double flash alternately. Then, press the [+] button until the signal lights go out to complete calibration.

Q: What should I do when the controller is not operating, the vibration cannot stop, it cannot be charged, or button functions are disordered?

A: For all functional problems with the controller, try restoring factory settings. Poke the reset button on the back of the controller with a thin needle to see if the issue is resolved.

FCC Information and Copyright

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

15.19 Labelling requirements:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Copyright © SHENZHEN SAITAKE ELECTRONIC CO.,LTD. All rights reserved.

Product Image: A portable wireless joypad with a black finish, featuring directional buttons, analog sticks, face buttons, and shoulder buttons. It is designed to attach to a console.