Instruction Manual for MERLIN models including: 58184-UPC 3 8 Inch NPT F Filter Regulator Lubricator, 58184-UPC, 3 8 Inch NPT F Filter Regulator Lubricator, Filter Regulator Lubricator, Regulator Lubricator, Lubricator
3/8 in. NPT(F) Filter /Regulator/Lubricator
3/8 NPT (F) FILTER/REGULATOR/LUBRICATOR IMPORTANT SAFETY INFORMATION 9. Keep bystanders out of the area during assembly. 1. Do not exceed maximum pressure. 2. If a problem occurs, have the problem corrected before further use. Do not use damaged equipment. 10. Do not assemble when tired or when under the influence of alcohol, drugs or medication. 11. Only use included adapter. Designed for compressed air use only. 3. RISK OF BURSTING! Never 12. Refer to compressor's instruction manual connect to an air source before installing any accessory. that is capable of exceeding 250 psi. 13. This product is not a toy. Do not allow children to play with or near this item. Over pressurizing the tool may cause bursting, abnormal operation, breakage of the tool or serious injury to persons. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated airpressure range. 14. Always dress appropriately for the task at hand noting loose articles of clothing, jewelry, or hair can become entangled in moving parts. 15. Do not leave tools connected to the air supply when not in use. 16. Do not leave the system pressurized or connected to the air supply when not in use. 4. Do not operate the Compressor in 17. Use as intended only. explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Compressor motors produce sparks 18. Inspect before every use; do not use if parts are loose or damaged. which may ignite the dust or fumes. 19. The warnings, precautions, and instructions 5. Assemble only according to these instructions. Improper assembly can create hazards. discussed in this manual cannot cover all possible conditions and situations that may occur with the given accessory and system the 6. Wear ANSIapproved safety goggles, ANSIapproved ear protection, and heavy duty work gloves during assembly. operator attached it to. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. 7. Turn off and unplug compressor before installing any accessory. 8. Keep assembly area clean and well lit. 20. Maintain product labels and nameplates on the tool. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. SAVE THESE INSTRUCTIONS Item 58184 For technical questions, please call 1-888-866-5797. 22h Specifications Flow Gauge Range Max. Pressure Filtration Inlet and Outlet Size 60 CFM Max. at 90 PSI 0 PSI 160 PSI 250 PSI 5 Microns 3/8 NPT Installation WARNING! TO PREVENT SERIOUS INJURY: Make sure air supply is off and release all residual pressure in system before installing Regulator. 1. Thread gauge onto front of Regulator body. 2. Securely mount tool in vertical position as close as possible to the tool connection. Note: Air flow must be in the same direction as arrow on tool body. 3. System piping should be 3/8 minimum. Avoid using unnecessary fittings and couplings that restrict the flow of air. 4. Make sure Connector is properly installed between the Filter/ Regulator and the Lubricator. 5. Connect air supply to Inlet Port. Connect air tool to Outlet Port. Connector Inlet Outlet Operating Instructions 1. Pull Adjustment Knob upwards to unlock. Turn Knob counterclockwise until it stops (closed position). Maintenance BEFORE EACH USE, inspect the general condition of the tool. Check for: · loose fittings · cracked or deformed orings · damaged pressure gauge or hose · any other condition that may affect its safe operation. Record Serial Number Here: 2. Turn Adjustment Knob clockwise until the desired outlet pressure is reached. 3. Push down on Adjustment Knob to lock. 1. Twist and pull downwards to remove Bowl. Clean or replace Filter as necessary. 2. Reinstall Filter and Bowl. Twist Bowl to lock in place. Note: If product has no serial number, record month and year of purchase instead. Note: Reference UPC 193175433947. SAVE THESE INSTRUCTIONS Item 58184 For technical questions, please call 1-888-866-5797. 22hAdobe PDF Library 16.0 Adobe InDesign 16.4 (Macintosh)