HAYWARD EC40C90 Series Perflex Extended Cycle Filtration Systems Owner's Manual

Owner's Manual for HAYWARD models including: EC40AC, EC40C90 Series, EC40C90 Series Perflex Extended Cycle Filtration Systems, EC40C90 Series, Perflex Extended Cycle Filtration Systems, Filtration Systems, Systems

W3EC50AC Perflex Modular Above Ground Pool D.E. Filter

W3EC40AC Perflex Modular Above Ground Pool D.E. Filter

Perflex Series

File Info : application/pdf, 8 Pages, 1.42MB

52845 2022111145240

ISEC40C90 Rev E

Perflex® Series
Extended Cycle Filtration Systems

Owner's Manual

Contents
Warnings....................................2 Introduction...............................4 Installation.................................4 Replacement Parts....................6 Warrantee ..................................6 Warrantee Registration ............8

Models: EC40AC and EC40C90 Series IMPORTANT SAFETY INSTRUCTIONS
Basic safety precautions should always be followed, including the following: Failure to follow instructions can cause severe injury and/or death.
This is the safety-alert symbol. When you see this symbol on your equipment or in this manual, look for one of the following signal words and be alert to the potential for personal injury.
WARNING warns about hazards that could cause serious personal injury, death or major property damage and if ignored presents a potential hazard.
CAUTION warns about hazards that will or can cause minor or moderate personal injury and/or property damage and if ignored presents a potential hazard. It can also make consumers aware of actions that are unpredictable and unsafe. The NOTICE label indicates special instructions that are important but not related to hazards.
Hayward Pool Products 620 Division Street, Elizabeth, NJ 07207
Phone: (908) 355-7995 www.hayward.com

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

WARNING - Read and follow all instructions in this owner's manual and on the equipment. Failure to
follow instructions can cause severe injury and/or death.
WARNING Suction Entrapment Hazard.
Suction in suction outlets and/or suction outlet covers which are, damaged, broken, cracked, missing, or unsecured can cause severe injury and/or death due to the following entrapment hazards:
Hair Entrapment- Hair can become entangled in suction outlet cover. Limb Entrapment- A limb inserted into an opening of a suction outlet sump or suction outlet cover that is damaged, broken, cracked, missing, or not securely attached can result in a mechanical bind or swelling of the limb. Body Suction Entrapment- A negative pressure applied to a large portion of the body or limbs can result in an entrapment. Evisceration/ Disembowelment - A negative pressure applied directly to the intestines through an unprotected suction outlet sump or suction outlet cover which is, damaged, broken, cracked, missing, or unsecured can result in evisceration/ disembowelment. Mechanical Entrapment- There is potential for jewelry, swimsuit, hair decorations, finger, toe or knuckle to be caught in an opening of a suction outlet cover resulting in mechanical entrapment.
WARNING - To Reduce the risk of Entrapment Hazards:
o When outlets are small enough to be blocked by a person, a minimum of two functioning suction outlets per pump must be installed. Suction outlets in the same plane (i.e. floor or wall), must be installed a minimum of three feet (3') [1 meter] apart, as measured from near point to near point.
o Dual suction fittings shall be placed in such locations and distances to avoid "dual blockage" by a user.
o Dual suction fittings shall not be located on seating areas or on the backrest for such seating areas.
o The maximum system flow rate shall not exceed 6 ft/sec in the suction return line
o Never use Pool or Spa if any suction outlet component is damaged, broken, cracked, missing, or not securely attached.
o Replace damaged, broken, cracked, missing, or not securely attached suction outlet components immediately.
o In addition two or more suction outlets per pump installed in accordance with latest ASME, APSP Standards and CPSC guidelines, follow all National, State, and Local codes applicable.
o Installation of a vacuum release or vent system, which relieves entrapping suction, is recommended.
WARNING Failure to remove pressure test plugs and/or plugs used in winterization of the pool/spa from the
suction outlets can result in an increase potential for suction entrapment as described above.
WARNING Failure to keep suction outlet components clear of debris, such as leaves, dirt, hair, paper and other
material can result in an increase potential for suction entrapment as described above.
WARNING Suction outlet components have a finite life, the cover/grate should be inspected frequently and
replaced at least every seven years or if found to be damaged, broken, cracked, missing, or not securely attached.
CAUTION Components such as the filtration system, pumps and heater must be positioned so as to prevent their
being used as means of access to the pool by young children. To reduce risk of injury, do not permit children to use or climb on this product. Closely supervise children at all times. Components such as the filtration system, pumps, and heaters must be positioned to prevent children from using them as a means of access to the pool.
WARNING Hazardous Pressure. Pool and spa water circulation systems operate under hazardous pressure during
start up, normal operation, and after pump shut off. Stand clear of circulation system equipment during pump start up. Failure to follow safety and operation instructions could result in violent separation of the pump housing and cover, and/or filter housing and clamp due to pressure in the system, which could cause property damage, severe personal injury, or death. Before servicing pool and spa water circulation system, all system and pump controls must be in off position and filter manual air relief valve must be in open position. Before starting system pump, all system valves must be set in a position to allow system water to return back to the pool. Do not change filter control valve position while system pump is running. Before starting system pump, fully open filter manual air relief valve. Do not close filter manual air relief valve until a steady stream of water (not air or air and water) is discharged.
WARNING Separation Hazard. Failure to follow safety and operation instructions could result in violent separation
of pump and/or filter components. Strainer cover must be properly secured to pump housing with strainer cover lock ring. Before servicing pool and spa circulation system, filters manual air relief valve must be in open position. Do not operate pool and spa circulation system if a system component is not assembled properly, damaged, or missing. Do not operate pool and spa circulation system unless filter manual air relief valve body is in locked position in filter upper body. Never operate or test the circulation system at more than 40 PSI. Do not purge the system with compressed air. Purging the system with compressed air can cause components to explode, with risk of severe injury or death to anyone nearby. Use only a low pressure (below 5 PSI), high volume blower when air purging the pump, filter, or piping.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

WARNING Risk of Electric Shock. All electrical wiring MUST be in conformance with applicable local codes,
regulations, and the National Electric Code (NEC). Hazardous voltage can shock, burn, and cause death or serious property damage. To reduce the risk of electric shock, do NOT use an extension cord to connect unit to electric supply. Provide a properly located electrical receptacle. Before working on any electrical equipment, turn off power supply to the equipment. To reduce the risk of electric shock replace damaged wiring immediately. Locate conduit to prevent abuse from lawn mowers, hedge trimmers and other equipment. Do NOT ground to a gas supply line.
WARNING Risk of Electric Shock Failure to ground all electrical equipment can cause serious or fatal electrical shock
hazard. Electrical ground all electrical equipment before connecting to electrical power supply.
WARNING Risk of Electric Shock Failure to bond all electrical equipment to pool structure will increase risk for
electrocution and could result in injury or death. To reduce the risk of electric shock, see installation instructions and consult a professional electrician on how to bond all electrical equipment. Also, contact a licensed electrician for information on local electrical codes for bonding requirements.
Notes to electrician: Use a solid copper conductor, size 8 or larger. Run a continuous wire from external bonding lug to reinforcing rod or mesh. Connect a No. 8 AWG (8.4 mm2) [No. 6 AWG (13.3 mm2) for Canada] solid copper bonding wire to the pressure wire connector provided on the electrical equipment and to all metal parts of swimming pool, spa, or hot tub, and metal piping (except gas piping), and conduit within 5 ft. (1.5 m) of inside walls of swimming pool, spa, or hot tub. IMPORTANT - Reference NEC codes for all wiring standards including, but not limited to, grounding, bonding and other general wiring procedures.
WARNING Risk of Electric Shock . The electrical equipment must be connected only to a supply circuit that is
protected by a ground-fault circuit-interrupter (GFCI). Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test button. The GFCI should interrupt power. Push reset button. Power should be restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the electrical equipment without the test button being pushed, a ground current is flowing, indicating the possibility of an electrical shock. Do not use this electrical equipment. Disconnect the electrical equipment and have the problem corrected by a qualified service representative before using.
CAUTION HAYWARD® pumps are intended for use with permanently-installed pools and may be used with hot tubs and
spas if so marked. Do not use with storable pools. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity.
WARNING Risk of Hyperthermia. To avoid hyperthermia the following "Safety Rules for Hot Tubs" are recommended by
the U.S. Consumer Product Safety Commission. 1. Spa or hot tub water temperatures should never exceed 104°F [40°C]. A temperature of 100°F [38°C] is considered safe for a healthy adult. Special caution is suggested for young children. Prolonged immersion in hot water can induce hyperthermia. 2. Drinking of alcoholic beverages before or during spa or hot tub use can cause drowsiness, which could lead to unconsciousness and subsequently result in drowning. 3. Pregnant women beware! Soaking in water above 100°F [38°C] can cause fetal damage during the first three months of pregnancy (resulting in the birth of a brain-damaged or deformed child). Pregnant women should adhere to the 100°F [38°C] maximum rule. 4. Before entering the spa or hot tub, users should check the water temperature with an accurate thermometer; spa or hot tub thermostats may err in regulating water temperatures by as much as 4°F (2.2°C). 5. Persons taking medications, which induce drowsiness, such as tranquilizers, antihistamines or anticoagulants, should not use spas or hot tubs. 6. If the pool/spa is used for therapy, it should be done with the advice of a physician. Always stir pool/ spa water before entering the pool/spa to mix in any hot surface layer of water that might exceed healthful temperature limits and cause injury. Do not tamper with controls, because scalding can result if safety controls are not in proper working order. 7. Persons with a medical history of heart disease, circulatory problems, diabetes or blood pressure problems should obtain a physician's advice before using spas or hot tubs. 8. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above normal body temperature of 98.6°F [37°C]. The symptoms of Hyperthermia include: drowsiness, lethargy, dizziness, fainting, and an increase in the internal temperature of the body.
The effects of Hyperthermia include:
1. Unawareness of impending danger. 2. Failure to perceive heat. 3. Failure to recognize the need to leave the spa. 4. Physical inability to exit the spa. 5. Fetal damage in pregnant women. 6. Unconsciousness resulting in danger of drowning.
SAVE THESE INSTRUCTIONS

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

The Hayward-Perflex is a high performance swimming pool filter. As a system it has an output rating of 2,400 gallons (9.1 KL) per hour. Manufactured from durable, corrosion-proof materials, the filter and pump are combined on a strong, molded mounting base. The systems are designed for continuous operation, for installation below, the pool water line. It may be used on fresh or salt water swimming pools.
The Perflex filter uses diatomite filter powder (commonly called D.E.). D.E. is the most efficient dirt remover known. It is normally fed into the system through the skimmer when the filter is initially started; then drained from the filter when it can no longer efficiently remove dirt from the water. Through the Perflex's exclusive "BUMP" action, the D.E. is periodically regenerated and the filter cycle extended without changing the powder. When the filter powder is totally used, the "BUMP" action makes it possible to drain the used diatomite without backwashing or dismantling the filter.
The Power-Flo MatrixTM series pump is a non-corrosive, centrifugal pump with pressure, flow, and safety features specifically designed for swimming pool service. It is driven by a heavy duty motor, which is electrically isolated and insulated from the pool water. Output pressure and flow are tuned to the filter, resulting in a perfectly balanced, non-corrosive system.

SYSTEM LOCATION
1. Though the system is designed for outdoor use, it is advisable to protect electrical components from the weather. Select a well-drained area, one that will not flood when it rains.
2. For best pump performance, the system MUST be located below the swimming pool water line. Set the mounting platform level. Keep the filter bump handle, drain outlet, and pressure gauge accessible for convenient operation. There is an alternate bump handle location on the other side of the filter outlet. Instructions for changing the handle position are covered later.
3. Position the system so that the filter tank can drain by gravity.
PLUMBING & INSTALLATION
1. To facilitate servicing of the filter system and to allow for indoor storage during the winter months, installing union connections at the suction and outlet ports is recommended.
2. Use 1-1/4" or 1-1/2" I.D. flexible plastic pipe, or hose, joined with insert fittings and stainless steel clamps. 3. All plumbing connections on the system are 1-1/2" N.P.T. When making connections, use plastic male-end adapters. Apply three turns of
Teflon tape or plastic pipe sealant compatible with ABS to the male threads. Screw the fitting into the thread hand tight; then, using a wrench, tighten one more full turn. Additional tightening is unnecessary-and-could result in damage to components. 4. Refer to the diagrams for suggested valving. Ball-type valves are recommended where needed. 5. Tighten pump base mounting bolts, if loose. 6. Securely hand tighten the union nut between the filter and pump. 7. Connect the pool suction plumbing between the skimmer, pool outlet, and the pump. 8. Connect the pool return (inlet) plumbing 9. If the pressure gauge is not installed, apply Teflon tape to the gauge threads, and carefully screw the gauge into the threaded hole in the side of the filter body. 10. A filter drain plug, with gasket, is furnished with each filter and is all that is needed for complete filter draining. If desired however, drain piping may be extended from the filter by using the optional Drain Valve Kit (Model SP0723) and an appropriate length of 1-1/2" pipe. Piping must slope away from the filter so the tank can drain by gravity. 11. All electrical connections should be made in accordance with applicable electrical codes. 12. Check for joint leaks before operating system. 13. Refer to pump instruction booklet for pump information.

BEFORE STARTING THE FILTER
1. Obtain a supply of operating chemicals, D.E., and a pool test kit. Use only the swimming pool grades of D.E., such as:

CELATOM®

A trademark of EP Minerals

DICALITE®

A trademark of EP Minerals

DE Filter media

Local Pool Supply

2. Superchlorinate the pool water by adding unstabilized granular or liquid chlorine. Stabilized forms of chlorine are recommended for normal daily use after the initial clean-up of the water. Follow chemical manufacturer's recommendations for superchlorination and daily use.
INITIAL SET-UP
1. Always turn off pump and relieve tank pressure by opening Air Relief Valve before loosening Center Clamp or servicing filter. 2. To re-assemble Clamp on filter, make sure Clamp is located and centered properly over the filter flange. If Clamp is tight, tap Clamp
with rubber mallet or block of wood to help seat it. Slide a Washer over each Bolt followed by a Spacer Tube. Insert Bolt assembly through both Clamp Halves. Slide on a Washer, secure with Hex Nut and hand tighten. Repeat on other side of Clamp. Alternately tighten both Bolt assemblies using a wrench and socket (1/2" drive). Alternately tighten until Spacer Tube is engaged (approx. 100 in-lbs). Finally, tighten 1/4 to 1/2 turn to secure (approx. 100 in-lbs). 3. To re-start system, open all in-line valves. Open Air Relief Valve before starting pump. Stand clear of filter and prime and start the pump per the manufacturer's instructions. When a steady stream of water emerges from the Air relief Valve, close Air Relief Valve.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

STARTING THE FILTER
Close the filter drain and the vent valve.
CAUTION: Separation Hazard. Failure to open all suction and discharge valves when starting the pump could cause
severe personal injury and/or property damage. To avoid open all suction and discharge valves.
Prime and start the pump following the manufacturer's instructions. Air trapped in the system will automatically vent to the pool. When there is a steady flow of water returning to the pool, the filter is ready for precoating. DO NOT operate the filter for more than one minute without the precoat charge.
PRECOATING
Scoop 4 lbs. (1.8 kgs.) of diatomite into the system through the skimmer as fast as the plumbing will take it. Note and record the pressure gauge reading after the diatomite has been added. This is the "precoat pressure."
FILTERING
Filtration starts as soon as the filter has been precoated. As the filter removes dirt from the pool water, the accumulated dirt causes a resistance to flow. As a result, the gauge pressure will rise and the flow will decrease. When the pressure rises 7-10 psi (.49-.70 Bar) above the precoat pressure, regenerate the filter.
REGENERATION (Extending the Cycle)
Stop the pump. Move the bump handle down slowly, then up briskly. Repeat 3 times. Restart the pump and filtration will resume at near the original flow and pressure. After each regeneration, and until the filter is cleaned, there may be a slight increase in the starting pressure. This is the result of dirt accumulating within the filter and is completely normal.
CLEANING
Cleaning is recommended when the gauge pressure rises more than 10 psi (.70 Bar) in less than a 24 hour period or when cloudy water returns to the pool for more than 30 seconds after regeneration. To clean, first stop the pump; then move the bump handle down slowly, then up briskly. Repeat 8 times. Open the vent valve (under bump cover), open the filter drain (Note: if the filter is installed below the pool water line, close the suction and return valves) and allow water and-dirt-to-empty completely.
After the filter has drained, and with the drain still open, run the pump for a few seconds to flush out any dirt remaining in the bottom of the filter. (Note: If the filter is installed below the pool water line, opening the suction valve for a few seconds with the pump off will adequately flush the unit.)
Close the filter drain and the vent valve. Open the suction and return valves (when used). Start the pump and let the filter fill with water and repeat the CLEANING procedure. This completes the cleaning phase. The filter is now ready for recharging. Proceed as in STARTING THE FILTER and PRECOATING.
VACUUMING
Vacuuming can be performed directly into the filter whenever needed. For fastest results, regenerate the filter before and after each vacuuming operation.
TO CHANGE BUMP HANDLE POSITION
1. Remove the bump handle grip. Push in tab at base of handle. Carefully pry the bump cover from the retaining groove and slide the cover off the handle.
2. Using a drift (or 10 penny nail), tap the pivot pin out of the filter head anchor point, freeing the end of the handle. Rotate the bump handle to the alternate position and align the handle and the head anchor holes. Tap the pivot pin in place.
3. Reinstall the bump cover and grip.
PREVENTIVE MAINTENANCE
While Perflex filters are basically resistant to the difficulties often encountered as a result of chemical build-up in swimming pools, it is important to keep in mind that the mineral content in a pool increases every day as a result of the chemicals and the normal water evaporation process. If the concentration of minerals is allowed to get too high, the minerals will form deposits on the Flex-Tubes inside the filter, and will eventually result in shortened filter cycles. To guard against this, a yearly chemical cleaning (soaking) of the Flex-Tube assembly is suggested. Use commercially available 20% muriatic acid added to water in 1 to 1 ratio; or use other commercial filter element cleaner mixed according to the package instructions. Use a plastic container.
CAUTION: Chemical Hazard Chemicals can cause personal or property damage, to avoid use personal protective gear when handling.
After cleaning, thoroughly flush all affected parts with cold water. Always wear gloves and eye protection when handling cleaning agents.
WINTERIZING
In areas where sub-freezing temperatures can be expected, the filter should be drained and removed from its operating location and stored indoors. Prior to removal, cycle the filter as described under CLEANING.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

REPLACEMENT PARTS

REF.

PART NO.

NO.

DESCRIPTION

ECX10066 Bump Mechanism Cover

ECX5000BP Filter Head with Vent Valve

ECX4034

Filter Body w/Flow Diffuser

ECX4000C Clamp Assembly with Hardware

ECX4000CHK Hardware Kit for Clamp Assembly

ECX1014A Shaft Kit

ECX1037B Bump Handle Grip

ECX4236A Bump Handle Screw Kit

ECX5000F Bump Shaft, 1/2" EC40AC

ECX1004

Tube Sheet (Top/Bottom)

ECX5000G Diaphragm Gasket

ECX1031

Flex-Tube Assembly

SPX1500NYA Tube Sheet Bolt Set

SP1022C

Plug with Gasket

SP0723

Ball-Type Drain Valve with Nipple

ECX2709A1 Pressure Gauge Back Mount

ECX1256

Flow Diffuser with Check Valve

ECX4077B1 Check Valve

SPX1055

Flow Controller

ECX4035

Flex-Tube Nest (Includes. 6, 9, 10, 11, 12 & 13)

SP1480

1-1/2" Male Union

SPX142576 0-Ring

Power-Flo Pump

SPX1250WA 6 ft. Cord Set

ECX1108A Pump Mounting Screw Set

EC1161PAK Platform Base with Screws

NO. REQ'D.
1 1 1 1 1 1 1 1 1 2 1 72 6 1 1 1 1 1 1
1
1 1 1 1 1 1

HAYWARD® Pool Products Limited Warranty
To original purchasers of this equipment, Hayward Pool Products, Inc. warrants its FILTERS to be free from defects in materials and workmanship for a period of ONE (1) year from the date of purchase, when used in single family residential applications. The limited warranty excludes damage from freezing, negligence, improper installation, improper use or care or any Acts of God. Parts that fail or become defective during the warranty period shall be repaired or replaced, at our option, within 90 days of the receipt of defective product, barring unforeseen delays, without charge. Proof of purchase is required for warranty service. In the event proof of purchase is not available, the manufacturing date of the product will be the sole determination of the purchase date. To obtain warranty service, please contact the place of purchase or the nearest Hayward Authorized Service Center. For assistance on your nearest Hayward Authorized Service Center please visit us at www.hayward.com. Hayward shall not be responsible for cartage, removal, repair or installation labor or any other such costs incurred in obtaining warranty replacements or repair. The Hayward Pool products warranty does not apply to components manufactured by others. For such products, the warranty established by the respective manufacturer will apply. The express limited warranty above constitutes the entire warranty of Hayward Pool Products with respect to its' pool products and is in lieu of all other warranties expressed or implied, including warranties of merchantability or fitness for a particular purpose. In no event shall Hayward Pool products be responsible for any consequential, special or incidental damages of any nature. Some states do not allow a limitation on how long an implied warranty lasts, or the exclusion of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

*Supersedes all previous publications.

Hayward Pool Products 620 Division Street Elizabeth, NJ 07207

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

SERVICE & REPAIRS
Consult your local authorized Hayward-Perflex dealer or service center. No returns may be made directly to the factory without the expressed written authorization of Hayward Pool Products, Inc.

ALGAE CONTROL

Algae is a form of plant life which can vary in size from a few thousandths of an inch to the size of a small tree. Of the many forms of algae, those most frequently found in swimming pool water are microscopic in size and green in color.

Algae readily grows in sunlight and can, under favorable conditions, quickly overgrow a swimming pool turning it completely green in just

a few hours. On the other hand, swimming pool water can be kept unfavorable to algae growth simply by maintaining a chlorine level of at

least 0.5 ppm in the water at all times. The chlorine level should be checked at least once a day using a suitable test kit.

If an algae condition develops and the pool water "blooms" green, superchlorination of the pool will be necessary to clear it. Add unstabilized granular chlorine, or liquid chlorine.

Follow chemical manufacturer's recommendation for superchlorination. The algae will quickly become inactive and can then be removed

by the filter. Live algae, on the other hand, multiplies so fast that the filter cannot keep up with its growth rate. In an active algae

situation, it may be necessary to regenerate the Perflex filter as frequently as every 2 to 3 hours.

When correctly used, commercial algaecides are effective against algae, though algaecides should be used in conjunction with, and not as a substitute for, regular chlorination or superchlorination.

Maintaining a chlorine level of at least 0.5 ppm in the pool water at all times is the most effective way to prevent algae growth in swimming

pools

SUGGESTED POOL CHEMISTRY LEVELS

ACTION REQUIRED TO CORRECT POOL CHEMISTRY

TO RAISE

TO LOWER

7.2 to 7.6

Add Soda Ash

Add Muriatic Acid or Sodium Bisulphate

TOTAL ALKALINITY

100 to 130 ppm Add Sodium Bicarbonate

Add Muriatic Acid

CHLORINE (UNSTABILIZED)

0.3 to 1.0 ppm

Add Chlorine Chemical

No action - chlorine will naturally dissipate

CHLORINE (STABILIZED)

1.0 to 3.0 ppm

Add Chlorine Chemical

No action - chlorine will naturally dissipate

CHLORINE STABILIZER

40 to 70 ppm

(Cyanuric Acid)

Add Stabilizer

Dilution - partially drain & refill pool with water that has not been treated with Cyanuric Acid.

PROBLEM
Running at high pressures.
Drop off of return flow.
Short cycles.
Short cycles -even after proper bumping, draining, and recharging

PROBABLE CAUSE
1. D.E. coated with normal accumulation of pool dirt, algae, etc. 2. Overcharge of D.E. 3. Restriction in return line caused by small eyeball fitting. 4. Partially closed valve on return line. 1. D.E. coated with normal accumulation of pool dirt, algae, etc. 2. Pump strainer basket clogged. 3. Skimmer basket clogged.
4. Pump impeller vanes clogged.
5. Air leak on suction side of pump.
6. Electric motor running less than maximum R.P.M. (under speed)

REMEDY
1. Bump. 2. Bump-Drain-Recharge. 3. Change to larger size fitting. 4. Open valve.
1. Bump. Clean. 2. Clean. 3. Cleaning with a stiff wire thru the pump strainer
opening will usually work. Alternate would be to disassemble-and clean. 4. Check cover gasket, hand knobs, hose, clamps, etc. Replace or tighten as necessary. 5. Consult pump and motor trouble shooting guide. NOTE: Most motor problems are due to: a) Undersized or improper wiring. b) Power cut-backs or a combination of both.

1. D.E. loaded to capacity with pool dirt, algae, etc. 2. Bumping incorrectly. 3. Bump handle bent. 4. Pump output exceeds design flow rate of filter.
5. Presence of algae.

1. Bump-Drain-Recharge. 2. Slow down stroke - brisk upstroke. Repeat 6
times. 3. Check and straighten or replace. 4. Check GPM/LPM output. Regulate pump
GPM/LPM output to max. filter GPM/LPM rating. 5. Super-chlorinate; Bump-Drain-Recharge as
needed.

Contaminated (clogged) Flex-Tube braids caused by: a. Natural accumulation of chemical deposits (accelerated if chemicals are fed thru skimmer). b. Running D.E. charge too long with excessive amount of live algae present in pool. c. Operating filter without D.E. d. Operating too long without D.E. after starting pump. D.E. must be added as soon as filter is full of water and pump is putting out a steady stream.
IMPORTANT -- Testing a new pool plumbing system without adding D.E. will cause this type of clogging.

Clean Tube Nest a) Detergent Cleaning: Remove tube nest and hose down with forceful stream of clean water. Soak tube nest in strong solution of laundry detergent (such as Cheer) and warm water. Hose down again.
b) Chemical Cleaning: This requires use of water and muriatic acid solution (or filter cleanertype preparations) to chemically dissolve contaminates. Consult your pool dealer for chemical cleaning instructions.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

PROBLEM
D.E. leaking to pool via the return lines.

PROBABLE CAUSE
1. Opening or tear in one or more Flex-Tubes. 2. Rip or hole in diaphragm gasket. 3. Worn or loose fitting diaphragm gasket (chemicals fed thru
suction lines may shorten life of this part). 4. Loose bolts on tube nest plates.

REMEDY
1. Replace Flex-Tube. 2. Replace gasket. 3. Replace gasket.
4. Tighten bolts.

Hard bumping.
D.E. leaking back to pool via skimmer or main drain.

1. Caking of D.E. under tube sheet. Sometimes caused by accumulation of sun tan oils, hair or floating particles that bind together in a clay-like form.
2. Overloaded with D.E. Sometimes happens when last charge of dirty D.E. was not properly drained.
3. Filter runs too long between bumping.
Filter check valve worn or stuck open.

1. Bump-Drain-Recharge more often and reduce the use of oils.
2. Bump-Drain-Recharge with proper amount of D.E.
3. Bump more frequently.
Clean and/or replace.

Very short cycles when vacuuming.

Normal if pool contains: 1. Very dirty water. 2. Presence of live, vigorously growing algae.
3. Presence of alum or floccing agents, which will clog filter.

1. Bump-Drain-Recharge more often. 2. Add enough chlorine to control this growth --
then vacuum. 3. Vacuum so as to by-pass filter. Avoid using floccing agents.

PRODUCT REGISTRATION
(Retain For Your Records)

DATE OF INSTALLATION ____________________
DETACH HERE: Fill out bottom portion completely and mail within 10 days of purchase/installation or register online.
-------------------------------------------------------------------------------------------------------------------------------------------------

Perflex® D.E. Filter

Warranty Card Registration

Please Print Clearly:

Years Pool has been in service

First Name____________________ Last Name_________________________ < 1 year 1-3 4-5 6-10 11-15 >15

Street Address__________________________________________________ Purchased from_____________________________
City_____________________________ State___________ Zip____________
Builder Retailer Pool Service Internet/Catalog
Phone Number_____________________ Purchase Date_________________ E-Mail Address__________________________________________________ Company Name_________________________________

Serial Number

Address_______________________________________

City____________________ State_____ Zip__________

Model Number_____________________________________________________ Pool Capacity_______________(U.S. Gallons)
If your product contains components that have individual serial numbers, it is not necessary to complete warranty registration for those individual components. Instead, complete warranty registration only for the overall product, using the serial number that is located on the outside of the product packaging.
Please include me on all e-mail communications regarding Hayward® Equipment or promotions.
Mail to: Hayward Pool Products, 620 Division Street, Elizabeth, NJ 07207 Attn: Warranty Dept Or REGISTER YOUR WARRANTY ON-LINE AT WWW.HAYWARD.COM

Phone_________________________________________
Type of Pool: Concrete/Gunite Vinyl Fiberglass Other_____________________________

New Installation

Replacement

Installation for:

In Ground

Above Ground

Spa

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

References

ayward.com

PDFium PDFium