MiLocks Model RF Keyless Entry Lock

RF Remote Control Programming

Program a Remote:

1. Press the 'S' button once.
2. Press and hold either button on the remote you wish to program within 5 seconds.
3. Two beeps indicate success. Zero beeps indicate a need to consult troubleshooting.

To Clear All Remotes:

1. Press the 'C' button once.
2. Press and hold either button on the remote you wish to delete within 5 seconds.
3. Two beeps indicate success. Zero beeps indicate a need to consult troubleshooting.

Note: This process deletes all stored remotes and programs the remote currently in use.

Troubleshooting

Low Batteries (Most Common Issue): If the lock produces a longer set of rapid beeps and either locks or does not lock the door, the batteries are low. Use brand new AA alkaline batteries.

Door Jam Alignment: Ensure the deadbolt and the hole in the door jam align to minimize resistance on the deadbolt.

Driver Bar Position: Verify the driver bar is in the vertical position with the deadbolt retracted during installation (Step 3). Ensure the thumb turn is positioned correctly based on the door latch side (Step 5). Incorrect positioning can lead to issues like the lock only working with a key, a jammed thumb turn, or a key that won't release.

Loose Keypad Connection: If the keypad wire harness is not securely connected, numbers may operate inconsistently. Test by pressing each number; all should beep. If some do not beep, inspect the back module (Part B) for pinched or torn wires. Check the keypad wires and ensure the pins in the male connection are not bent. Reconnect and retest.

Function Test: If a passcode is not programmed, the keypad will not operate. To check if a passcode is stored:

1. Unlock the door and keep it open.
2. Press the LOCK button on the keypad once and listen for beeps:
• 3 beeps and no lock: No passcode is set. Refer to programming instructions.
• Longer rapid beeps: Low batteries. Replace with 4 premium "AA" alkaline batteries.
• 2 beeps and successful lock: At least one passcode is stored, and the lock is operating correctly.

Warranty

MiProducts Corporation warrants the product to the original residential user for 1 year from the date of purchase against defects in materials and workmanship under normal use. A copy of the original purchase receipt is required. This warranty excludes abuse, misuse, or commercial applications. All mechanical components have a limited 25-year warranty. The exterior finish has a limited lifetime warranty against deterioration from normal weather conditions. The warranty does not cover improper installation, modifications, or acts of God. MiProducts Corporation's liability is limited to repair or replacement at their discretion and does not cover installation, removal, or reinstallation costs, nor consequential damages. Replacement parts are covered, but shipping and handling fees are not.

For warranty claims or assistance, contact MiProducts Corporation at 1-800-355-0157 (M-F, 9 am - 5 pm PST, English & Spanish) or visit www.milocks.com.

Contact Information: MiProducts Corp., La Puente, CA 91746, 1-800-355-0157

Product Information

Model: RF

Made In: Taiwan

Tools Required (not included): Phillips Screwdriver

Power Source: (4) AA Batteries

Left Handed & Right Handed Setting: On the back module (Part B), a switch labeled "1-2" controls this setting: 1 = Right Hand Doors (most common), 2 = Left Hand Doors. Determine door handedness by hinge location when entering the doorway.

General Warnings & Cautions

1. The back module (Part B) must be protected from the weather.
2. Remote control operates up to 30 feet without obstructions.

Assistance: For assembly, installation, parts, or customer service, call 1-800-355-0157 (English & Spanish) from 9 am - 5 pm PST, Monday - Friday (North America).

Battery Precautions:

• Do not mix old and new batteries.
• Do not use rechargeable batteries.
• Remove batteries for extended storage.
• Do not dispose of batteries in fire; they may explode. Follow local disposal procedures.
• Do not puncture batteries; electrolyte leakage is corrosive and toxic.
• Prevent conductive materials (jewelry, tools) from contacting batteries to avoid short circuits, extreme heat, and burns.

Register Your Product: Register your product at www.milocks.com to validate the warranty and keep a record with MiProducts Corporation.

Installation Steps

1. Adjust Latch Backset: Select 60mm (2 3/8") or 70mm (2 3/4").
2. Install Door Latch (w/ Bolt Retracted).
3. Mount Front Module.
4. Fasten Back Mounting Plate.
5. Connect, Mount & Fasten Back Module.
6. Install Battery Cover.