User Guide for Cynova models including: AF336 Osmo Action GPS Bluetooth Remote Controller, AF336, Osmo Action GPS Bluetooth Remote Controller, Action GPS Bluetooth Remote Controller, GPS Bluetooth Remote Controller, Bluetooth Remote Controller, Remote Controller
Shenzhen Cynova Technology Co.,Ltd. AF336 2BAUF-AF336 2BAUFAF336 af336
1 day ago — controller”) connect to the camera via Bluetooth ... During linking, the status LED of the remote ... End user must follow the specific operating instructions for ...
3 days ago — This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. ISED Compliance Notice. CAN ICES-003 (B) / NMB-003(B).
Osmo Action GPS Bluetooth Remote Controller Introduction Osmo Action GPS Bluetooth Remote Controller (hereinafter referred to as" remote controller") connect to the camera via Bluetooth. Users can control the camera remotely and capture footages with the remote controller.The remote controller supports single-camera control and also multi-camera control mode so that users can shoot with up to 16 cameras simultaneously. The built-in satellite positioning modules enable users to record accurate datain motion. With the wrist strap, the remote controller can be installed on different place like the handlebar of the bicycle, which flexibly change the position to shoot various sports scenes. Overview Button Features Quick Switch Button Operation Press Once Press and Hold Description Switch between shooting modes Power on or off the remote controller Shutter/Record Button Operation Description Press Once Take a photo or start/stop recording Link Button Operation Press Once Press and Hold Description Put the camera into or exit sleep mode(with the relevant settings in the camera enabled) Link the remote controller and the camera Button Combinations Operation Description Press and hold the link button Forget the Bluetooth connection and start linking and the quick switch button for four seconds Press and hold the link button Switch between single-camera control mode and and the shutter/record button multi-camera control mode and start linking. for four seconds Screen Information When controlling a single camera, the screen displays the status and battery level of the connected camera. When controlling multiple cameras, the screen displays the number of cameras connected. The display on the screen varies depending on the camera mode. The screen will enter sleep mode if there no operation after 3 minutes and the remote controller will power off if there is still no operation after a further 10 minutes if there is no camera connected and the remote controller is not charging. When the screen is off, press any button to exit sleep mode and continue using the remote controller. Operation Linking Linking in single-camera control mode When powered on, the remote controller will automatically search for and connect to any DJI Osmo Action 4 cameras.Follow the prompts on the camera screen to operate linking. Linking in multi-camera control mode When powered on, the remote controller will be in single-camera control mode by default. Press and hold the link button and the shutter/record button for four seconds to switch into multi-camera control mode. Then the remote controller searches for the cameras and start linking with each camera. Follow the prompts on the camera screen to operate linking. When controlling multiple cameras, the screen displays the number of cameras connected. During linking, the status LED of the remote controller will blink blue. After linking to the camera, users can control the camera remotely and capture footage with the remote controller. Controlling the Cameras Single-Camera Control Mode In single-camera control mode, press the quick switch button once to switch between shooting modes. The shooting modes that can be switched are the same as the settings in the camera. Press the shutter/record button once to take a photo or to start or stop recording. Multi-Camera ControlMode In multi-camera control mode, the remote controller can control each camera to use its own shooting mode to shoot by default. Press the quick switch button to set all cameras to a unified shooting mode.Press the shutter/record button once to take a photo or start recordingand press twice to stop recording.The shooting parameters will be based on the presets of each camera in this mode. Dashboard The built-in satellite positioning modules enable users to record fitnessdataaccurately when shooting. Used with DJI Mimo app, users can add a host of data to embellish the video, such as speed, route, direction, and Elevation. Charging the Remote Controller Connect the remote controller to a charger via the USB-C port. Status LED Descriptions Status LED Charging Status When Powered off Solid green for 6 seconds and turns off Blinks green four times Blinks green three times Blinks green twice Blinks green System Status Blinks red three times Blinks blue Work Status Solid green Temporarily off Blinks red Description Charging completed Charging76%-100% Charging51%-75% Charging26%-50% Charging0%-25% Powering off Linking Ready to use Taking a photo Recording a video Specifications Model Dimensions Weight GNSS Bluetooth Protocol Operating Frequency Transmission Power (EIRP) Built-in Battery Capacity Charging Temperature Operating Temperature OSMO-AF-336 40.45×38.6mm×20.45mm 23.34g GPS/BEIDOU/GALILEO BLE 5.3 2.402-2.480 GHz < 4 dBm 270mAh 0° to 45° C (32° to 113° F) -10° to 45° C (14° to 113° F) FCC Compliance Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. ISED Compliance Notice CAN ICES-003 (B) / NMB-003(B) This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :(1)L'appareil ne doit pas produire de brouillage; (2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.The portable device is designed to meet the requirements for exposure to radio waves established by the CNR-102. Cet équipement est conforme aux limites d'exposition aux rayonnements RSS-102 établies pour un environnement non contrôlé. L'utilisateur final doit suivre les instructions spécifiques pour satisfaire les normes. Cet émetteur ne doit pas être co-implanté ou fonctionner en conjonction avec toute autre antenne ou transmetteur. Le dispositif portatif est conçu pour répondre aux exigences d'exposition aux ondes radio établie par le développement énergétique DURABLE.Adobe PDF Library 11.0