Instruction Manual for LOVMOR models including: VDDB42-E 42 Bathroom Vanity Single Sink Storage Unit, VDDB42-E, 42 Bathroom Vanity Single Sink Storage Unit, Vanity Single Sink Storage Unit, Single Sink Storage Unit, Sink Storage Unit, Storage Unit
LOVMOR 42'' Bathroom Vanity, Single Sink Storage Unit, Large Capacity for Laundry Room, Kitchen, Shower Room & Utility Room. : Tools & Home Improvement
Vanity Double Drawer Base Cabinet Instruction Manual MODEL: VDDB42-E C BOX BACK PANEL G2 DRAWER SIDE PANEL - RIGHT I DRAWER BACK PANEL A2 BOX SIDE PANEL - RIGHT H DRAWER BOTTOM PANEL G1 DRAWER SIDE PANEL - LEFT D FACE FRAME F1 DRAWER FACE PANEL A1 BOX SIDE PANEL - LEFT F2 DRAWER FACE PANEL J DOOR PANEL B BOX BOTTOM PANEL E TOE KICK PANEL PART A1 A2 B C D E F1 DESCRIPTION Box side panel - left Box side panel - right Box bottom panel Box back panel Face frame Toe kick panel Drawer face panel PART F2 G1 G2 H I J DESCRIPTION Drawer face panel Drawer side panel - left Drawer side panel - right Drawer bottom panel Drawer back panel Door panel CAUTION Be sure to carefully remove all parts from the carton and ensure that there are no damages to any of them. The hardware should be kept away from children when unpacking and assembling this product. Two adults are recommended for assembly. Follow the instructions in the instruction manual carefully and strictly to ensure that the product is assembled and operates as intended. Do not tighten all the screws until all the adjacent parts have been properly connected. Please do not throw away extra screws.Please refer to the actual product for the screw hole position. HARDWARE CONTENTS AA Glide and runner profile x 12 L Included: 5/8" Flat Head Phillips Screw x 60 R BB Adjustable drawer clips x 12 5/8" *Two additional pieces are included as an extra Included: 5/8" Flat Head Phillips Screw x 24 3/8" Flat Head Phillips Screw x 24 3/8" - 1 - CC Soft - close hinge x 2 Be careful the length of the screws. 3/4" 1/2" 1/2" DD Wood corner block x 4 Included: 1/2" Flat Head Phillips Screw x 4 3/4" Round Head Phillips Screw x 2 Included: 1" Flat Head Phillips Screw x 8 EE Corner brace x 13 Included: 1/2" Round Head Phillips Screw x 52 GG 1" Flat head Phillips screw x 5 HH Rubber bumper x 26 TOOLS REQUIRED (NOT INCLUDED) - 2 - INSTALLATION OVERVIEW 1 EE A1 A2 EE Use 1/2" round head phillips screw x 20 2 3 A2 C EE A2 C Use 1/2" round head phillips screw x 6 4 B C 5 C A2 B Use 1/2" round head phillips screw x 6 - 3 - 6 A1 B C 85 A2 D 7 A1 B A2 C Use 1/2" round head phillips screw x 4 9 5 Inside B 10 E B B A2 Use 1/2" round head phillips screw x 8 11 A2 EE Bottom B Use 1/2" round head phillips screw x 8 - 4 - 12 13 AA AA Rotate A1 A2 C 1" Flat head Phillips screw x 5 14 Use 5/8" flat head phillips screw x 24 15 AA A1 AA A2 Use 5/8" flat head phillips screw x 24 16 17 G2 F1 - 5 - 18 G2 F1 G1 20 I 19 G1 I H G2 21 G1 H G2 F2 F1 22 x4 23a BB F1 G2 H G1 I F2 Use 5/8" flat head phillips screw x 4 Be careful of the screw type. - 6 - 23b 24b 24a F1 BB G2 H G1 I Use 3/8" flat head phillips screw x 4 Be careful of the screw type. 25 26a 26b Insert the drawer on the extended runner. To secure the drawer clips with the runner, push the drawer in. Upon successful locking, a click can be heard. - 7 - 26c 26d 3 3 Ensure that the hook on each runner profile fits into the corresponding holes on the drawer back panel. 2 2 1 To level the drawer, use the green spur gears 1 to adjust drawer left and right, the green spur gears 2 to adjust drawer up and down, and the green spur gears 3 to adjust drawer inside and outside. 26e 27a CC J To take the drawer out, push the green clips at the same time to unlock drawer clips. Use 1/2" flat head phillips screw x 4 27b 28a CC Use 3/4" round head phillips screw x 2 - 8 - 28b 28c If the door is not level when it is installed, the customer will need to turn the screw clockwise to extend the hinge or counterclockwise to shorten the hinge. 29 DD x4 Some products may have hinges pre-installed. To reverse the door, unscrew the 3/4" round head phillips screws from each hinge and remove the door panel. Then, reverse the door panel and drill the 3/4" round head phillips screws to each hinge through the pre-drilled holes to tighten the hinges with cabinet face frame. 30 DD 31 HH x26 1" Flat Head Phillips Screw x 8 (2 screws for 1 corner block) Dear customers, Thank you for purchasing our product. If you require assistance, please contact the customer service team at the retailer where you purchased the product. The customer service team will be happy to assist you. - 9 -Adobe PDF library 16.03 Adobe Illustrator 26.0 (Windows)