THE OUTDOOR GREATROOM COMPANY BRON5151-K Bronson Block Gas Fire Pit Kit Owner's Manual

Owner's Manual for THE OUTDOOR GREATROOM COMPANY models including: BRON5151-K Bronson Block Gas Fire Pit Kit, BRON5151-K, Bronson Block Gas Fire Pit Kit, Gas Fire Pit Kit, Fire Pit Kit, Pit Kit

Owner's Manual

The Outdoor Greatroom Company Bronson Block Gas Fire Pit Kit — Cozy Glow Stoves

File Info : application/pdf, 32 Pages, 2.58MB

JavaScript is disabled. Open the PDF or Download.

TOGC Bronson Block Fire Pit Kit Owners Manual ?v=11983992799194753295

Bronson Fire Pit
Installation Instructions for Bronson Pit Table
BRON5151-K
outdoorrooms.com

! IMPORTANT !
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to the burner
installation including: lighting and operating instructions, safety information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT CONSULTING THE CRYSTAL FIRE® PLUS OWNER'S MANUAL.

CONTENTS

1. About Your Fire Table

a. Required Tools

b. Included With Your Fire Pit

2. Setting Up Your Burner

3. Assembly Instructions

a. Unpacking

b. 1-3 Brick Row Assembly

c. CF-SPARKER Assembly

d. Control Panel Assembly

e. Thermocouple Installation

f. Electrode Installation

4. Finishing Fire Pit

a.Control Panel Attachment b. Final Brick Layer Assembly c. Fire Media Installation

5. Operating Instructions

6. Warnings

7. Warranties

42527 REV C 01-20-22

outdoorrooms.com

1. ABOUT YOUR FIRE TABLE
A. REQUIRED TOOLS
· Utility Knife
To cut and remove packaging
· 2 Open Ended Wrenches
To secure gas connections
· Phillips Screw Driver (Do not use a drill to assemble)
For assembly
· One AAA Battery (Not Included)
Required for electric spark igniter installation
B. INCLUDED WITH FIRE PIT KIT

7.88"

11.75"

4.00"

11.75" X 7.875" X 4.00" Brick (42)

7.88"

4.00"

4.00"
7.875" X 4.00" X 4.00" Brick (6)

BI28 Burner and Accessories (1)

Tumbled Lava Rock (LAV-TMB) (13)

42 Inch Square Burner Plate (BP42S) (1)

Control Panel (10259) (1)

Control Panel Block (10366) (1)

Vent Block (10367) (2)

34" Whistle Free Stainless Steel
Flex Line (10367) (1)

Refer to Crystal Fire® Plus manual for items included with Crystal Fire® Plus burners

outdoorrooms.com

2. SETTING UP YOUR BURNER
! ATTENTION !
Read and understand your Crystal Fire® Plus owner's manual before beginning burner hookups or using the device.
DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.
! IMPORTANT !
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to the burner installation including: lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches. DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE® PLUS OWNER'S MANUAL.
A. GAS CONNECTIONS
· See Crystal Fire® Plus instructions for burner installation.
· All gas connections were completed at the factory.
· Check all connections for leaks. If needed, tighten connection with 2 wrenches and re-check for leaks.
· For hard piped installations. Connect the gas supply line (not included) to the 3/8" male flare fitting on the valve.USE TWO WRENCHES TO ENSURE A GAS TIGHT CONNECTION.

outdoorrooms.com

3. ASSEMBLY INSTRUCTIONS
! WARNING !
Exposed edges may be rough, use leather gloves when removing packaging and handling the bricks.

A. UNPACKING
Do not discard any packaging until assembly is complete and unit is tested. Keep all included manuals in a safe place for future reference. Keep bricks stacked until ready to be placed.

B. 1-3 BRICK ROWS ASSEMBLY
1. Once desired location for fire pit has been determined, start with
placing first layer of bricks. Follow the diagram shown below for layout pattern.

LAYER 1

Key A - 11.25" x 7.875" block B - 4.00" x 7.875" block

FRONT

outdoorrooms.com

2. Continue on to second row of bricks. This layer will contain the 2
vent blocks (included in kit). Follow diagram shown below for layout pattern.

LAYER 2

A BA

VENT BLOCK

Key A - 11.25" x 7.875" block B - 4.00" x 7.875" block

A BA

FRONT

3. Continue on to third row of bricks. This layer will contain the control
panel block (included in kit). Follow diagram shown below for layout pattern.

LAYER 3

Key A - 11.25" x 7.875" block B - 4.00" x 7.875" block

CONTROL PANEL BLOCK FRONT

outdoorrooms.com

4. Unpack burner. Before installing the burner into the burner plate,
remove the 24 inch flex line between burner orifice and valve and connect included 34 inch flex line. Use 2 wrenches to tighten and perform leak test. Set burner into burner plate. Position burner plate in center of fire pit and then pull plate so that end is slightly off edge. Leave a gap bewteen control panel block and burner plate so that hands are able to fit and make connections outlined in future steps.
BURNER PLATE AND BURNER
WORKABLE GAP
CONTROL PANEL BLOCK FRONT

outdoorrooms.com

C. CF-SPARKER ASSEMBLY
· Locate CF-SPARKER inside of Crystal Fire® Plus burner box. · Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included)
with + end out. · Install CF-SPARKER into control panel as shown below. CF-SPARKER must be
installed BEFORE control valve. · Press in CF-SPARKER button to test your sparker.
CF-SPARKER
D. CONTROL PANEL ASSEMBLY · Pull the VCSV valve through the back and then front opening of the control panel block. · Connect a whistle free flexible gas supply line to the inlet of valve using a ½" flare nut. · Attach burner valve to control panel with provided screws. Ensure CF-SPARKER is installed before this step.
BURNER WHISTLE FREE SUPPLY FLEX LINE MAIN GAS SUPPLY

CTRL PANEL

VCSV

outdoorrooms.com

E. THERMOCOUPLE INSTALLATION
· Refer to Crystal Fire® Plus instruction manual for detailed attachment of thermocouple.
· Attach thermocouple to burner valve as shown below.

C. ELECTRODE INSTALLATION · Connect igniter and ground wire to sparker box. Both wires can connect to
either connection point. The unit will operate in either configuration. · Test system by pushing the button on the igniter. Consult the troubleshooting section of the Crystal Fire® Plus owner's manual if the spark is weak, intermittent or not present.
*Flexline removed in image for visibility.

ELECTRODE WIRES

outdoorrooms.com

4. FINISHING FIRE PIT
A. CONTROL PANEL ATTACHMENT Push control panel back into control panel block, making sure all connections are tucked in and not kinked. Using the 4X provided metal screws, attach the control panel to the control panel block. Finalize by pressing the control panel knob onto the stem of the VCSV valve.
CTRL PANEL

SCREWS (4X)

KNOB

B. FINAL BRICK ROW ASSEMBLY Move burner and burner plate back towards center of fire pit. Place final layer of bricks. Follow diagram shown below for layout pattern.

LAYER 4

A BA

Key A - 11.25" x 7.875" block B - 4.00" x 7.875" block

A BA

FRONT

outdoorrooms.com

C. FIRE MEDIA INSTALLATION · Scatter all included glass beads, lava rock, or other approved fire media evenly across entire burner surface.
! WARNING !
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT INCLUDED GLASS BEADS OR OTHER APPROVED
FIRE MEDIA.

outdoorrooms.com

5. OPERATING INSTRUCTIONS

! IMPORTANT !
Before operating your BRON5151, ensure all gas connections are properly tightened and thoroughly leak checked. Refer to the Crystal Fire® Plus manual for
information on proper leak checking and other critical safety information.

WARNING !

FIRE OR EXPLOSION HAZARD
If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

Verify control valve is in OFF position. If operating on a self-contained propane
cylinder, ensure cylinder valve is CLOSED. If operating on a hard-piped system, ensure main gas supply shut-off valve and all other valves in gas system are
OPEN.

If operating on a self-contained propane cylinder, slowly open cylinder valve.

Press and hold sparker button. Verify an audible and visible spark is present within the ignition wind guard.

Gently press and turn control knob to LOW/IGNITION position. Fully depress control knob and hold for 3-5 seconds. Burner should ignite and continue to operate when control knob is released.

If burner does not light or remain lit after 20 seconds of attempting ignition, turn control valve to OFF position and wait 5 minutes to allow gas to dissipate before attempting ignition again. DO NOT ATTEMPT TO LIGHT BURNER IF YOU SMELL GAS.
With burner lit and operating, the flame height can be adjusted between LOW and HIGH at any time.

OFF
LOW/ IGNITION
HIGH PUSH AND HOLD
TO IGNITE

LOOK FOR SPARK HERE
DEPRESS SPARKER BUTTON

HOLD KNOB IN FOR 3-5 SECONDS
ROTATE COUNTER-CLOCKWISE TO LOW AND SLOWLY DEPRESS
PRESS AND HOLD SPARKER BUTTON

OFF
LOW/ IGNITION
HIGH

outdoorrooms.com

6. WARNINGS
! IMPORTANT !
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to the burner installation including: lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches. DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT
FIRST CONSULTING THE CRYSTAL FIRE® PLUS OWNER'S MANUAL.
! WARNING !
After consulting the manual and following instructions, remember: before operating, all gas connections must be fully checked for leaks.

outdoorrooms.com

7. WARRANTIES

PRODUCT CATEGORY

WARRANTY INFORMATION

GAS FIRE PIT TABLES/CRYSTAL FIRE® PLUS BURNER

Limited lifetime warranty on all stainless steel burners installed in a residential setting, and 5 years on all stainless steel burners installed in a commercial setting.
One year warranty on ignition & electronics
One year finish warranty
Three year structural warranty on all fire pit bases and tops

outdoorrooms.com

Thank you for purchasing an Outdoor GreatRoom Company product! This fire pit was made
with pride in the USA.
Warranty: Fire pit tables are covered under a 1 year manufacturer's warranty.
Please visit http://www.outdoorrooms.com/product-registration to register your product.
9583 217th St. W. · Lakeville, MN 55044 Toll Free: 1-866-303-4028 · Sales@OutdoorRooms.com
outdoorrooms.com

Bronson Fire Pit
Installation Instructions for Bronson Pit Table
BRON52-K
outdoorrooms.com

CONTENTS

1. About Your Fire Table

a. Required Tools

b. Included With Your Fire Pit

2. Setting Up Your Burner

3. Assembly Instructions

a. Unpacking

b. 1-3 Brick Row Assembly

c. CF-SPARKER Assembly

d. Control Panel Assembly

e. Thermocouple Installation

f. Electrode Installation

4. Finishing Fire Pit

a.Control Panel Attachment b. Final Layer Assembly c. Fire Media Installation

5. Operating Instructions

6. Warnings

7. Warranties

42528 REV C 01-20-22

outdoorrooms.com

4.00

8.00 7.75

5.50

7.75" X 5.50" X 4.00" Brick (84)

Capstone (Optional) (4)

BI28 Burner and Accessories (1)

Tumbled Lava Rock (LAV-TMB) (12)

42 Inch Round Burner Plate (BP42RD) (1)

Control Panel (10259) (1)

Control Panel Block (10393) (1)

Vent Block (10394) (2)

34" Whistle Free Stainless Steel
Flex Line (10367) (1)

Refer to Crystal Fire® Plus manual for items included with Crystal Fire® Plus burners

outdoorrooms.com

3. ASSEMBLY INSTRUCTIONS
! WARNING !
Exposed edges may be rough, use leather gloves when removing packaging and handling the bricks.
A. UNPACKING
Do not discard any packaging until assembly is complete and unit is tested. Keep all included manuals in a safe place for future reference. Keep bricks stacked until ready to be placed.
B. 1-3 BRICK ROWS ASSEMBLY 1. Once desired location for fire pit has been determined, start with placing first layer of bricks. Follow the diagram shown below for layout pattern.
LAYER 1

FRONT

outdoorrooms.com

2. Continue on to second row of bricks. This layer will contain the 2
vent blocks (included in kit) and the control panel block (included in kit). Follow diagram shown below for layout pattern.
LAYER 2

VENT BLOCK

CONTROL PANEL BLOCK FRONT
3. Continue on to third row of bricks. Follow diagram shown below for
layout pattern.
LAYER 3

FRONT

outdoorrooms.com

4. Unpack burner. Before installing the burner into the burner plate,
remove the 24 inch flex line between burner oriface and valve and connect included 34 inch flex line. Use 2 wrenches to tighten and perform leak test. Set burner into burner plate.
Position burner plate in center of fire pit and then pull plate so that end is slightly off edge. Leave a gap bewteen control panel block and burner plate so that hands are able to fit and make connections outlined in future steps.

WORKABLE GAP

BURNER PLATE AND BURNER

outdoorrooms.com

CTRL PANEL

VCSV

outdoorrooms.com

E. THERMOCOUPLE INSTALLATION
· Refer to Crystal Fire® Plus instruction manual for detailed attachment of thermocouple.
· Attach thermocouple to burner valve as shown below.

ELECTRODE WIRES

outdoorrooms.com

SCREWS (4X)

KNOB

B. FINAL BRICK LAYER ASSEMBLY Move burner and burner plate back towards center of fire pit. Place bricks as final layer. Follow diagram shown below for layout pattern.

LAYER 4

LAYER 4 (optional capstone)

CAPSTONE

FRONT

OPTIONAL CAPSTONE SETUP: The BRON52-K has an optional captone. The capstone can be place on top of layer 3 (replacing the brick of layer 4) or on top of layer 4. When using the optional capstone ensure that the burner plate is one layer below the capstone.

outdoorrooms.com

5. OPERATING INSTRUCTIONS

! IMPORTANT !
Before operating your BRON52, ensure all gas connections are properly tightened and thoroughly leak checked. Refer to the Crystal Fire® Plus manual for
information on proper leak checking and other critical safety information.

WARNING !

FIRE OR EXPLOSION HAZARD
If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

If operating on a self-contained propane cylinder, slowly open cylinder valve.

Press and hold sparker button. Verify an audible and visible spark is present within the ignition wind guard.

Gently press and turn control knob to LOW/IGNITION position. Fully depress control knob and hold for 3-5 seconds. Burner should ignite and continue to operate when control knob is released.

OFF
LOW/ IGNITION
HIGH PUSH AND HOLD
TO IGNITE

LOOK FOR SPARK HERE
DEPRESS SPARKER BUTTON

HOLD KNOB IN FOR 3-5 SECONDS
ROTATE COUNTER-CLOCKWISE TO LOW AND SLOWLY DEPRESS
PRESS AND HOLD SPARKER BUTTON

OFF
LOW/ IGNITION
HIGH

outdoorrooms.com

7. WARRANTIES

PRODUCT CATEGORY

WARRANTY INFORMATION

GAS FIRE PIT TABLES/CRYSTAL FIRE® PLUS BURNER

outdoorrooms.com

References

Adobe InDesign 17.0 (Windows) Adobe PDF Library 16.0.3