Instruction Manual for PEMKO models including: SDL_, SDL_-ADA, SDL Privacy Barn Door Lock Surface Jamb Mount, SDL, Privacy Barn Door Lock Surface Jamb Mount, Door Lock Surface Jamb Mount, Surface Jamb Mount, Jamb Mount
Architectural Door Accessories SDL Privacy Barn Door Lock Surface Jamb Mount Instructions Installation based on barn door application where doors are hung on OUTSIDE of room. - Install lock on jamb wall facing opening - Install strike with an emergency release on barn door - Adjustable strike for door thickness from 1-3/8" to 2" - Thick door kits available Part Number SDL_ SDL_ -ADA Deadbolt 1" 1" Thumb-Lever 13/16" 1-9/16" Lock Case 3-9/16" x 1-7/8" x 9/16" 3-9/16" x 1-7/8" x 9/16" SDL Series Privacy Door Lock Set Parts: Items Lock Strike Other No. Description 1 #8 x 1-1/2" Wood Combo Screw 2 Mounting Plate 3 M3 x 7mm Handing Screw 4 M3 x 6mm Thumb Piece Screw 5 M4 x 6mm Installation Screw 6 Thumb Piece 7 M3 x 6mm Cover Screw 8 Lock Body Cover 9 Barn Door Lock Body 10 Dust Proof Strike 11 Washer 12 Hollow Screw 13 4mm Allen Wrench 14 Emergency Key 15 Decorative Cap - Door Prep Template - Installation Instruction Function/Privacy 4 EA 1 EA 1 EA 2 EA 4 EA 1 EA 1 EA 1 EA 1 EA 1 EA 1 EA 1 EA 1 EA 1 EA 1 EA 1 EA 1 EA Tools Needed: Door Wall Lock Jamb Emergency Key Dust-Proof Strike 1 2 34 5 67 15 14 9 8 10 11 12 13 Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited. 81056 10/19 1. Prep Wall and Door Ensure minimum 1" (25mm) door overlap before installing SDL Privacy Lock. Lock Side Min 1" 2. Prep Jamb Use template to mark and drill pilot holes. Remove door if it interferes with lock installation. Jamb Trim Face Bore 42" Ø1/8" 3. Hand Lock if necessary Install thumb lever to lock. (Fig 1) Using a #1 Phillips screwdriver, remove handing screw and discard. (Fig 2) Flip lever position to opposite orientation. (Fig 2) Install new handing screw from screw pack. Fig 1 Handing Screw Left Hand Fig 2 Right Hand Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited. 81056 10/19 2 4. Install Lock Attach mounting plate to door jamb using four (4) combo screws. (Fig 1) Install lock body and secure with four (4) installation screws. (Fig 2) Install lock cover and screw. (Fig 3) · Slide front of cover over body, hooking alignment tab onto body. · Push back of cover over body to snap into place. Fig 1 Fig 2 Fig 3 5. Prep Barn Door for Dust Proof Strike with Emergency Release Close barn door; throw lock bolt to mark exact strike center position. Ensure minimum of 1" to edge of door. (Fig 1) Using strike center as guide, drill pilot hole through door from strike side with 1/8" bit. With pilot hole as guide, use 1" hole saw to drill Fig 1 1-1/4" deep hole. DO NOT DRILL THROUGH DOOR. (Fig 2) Using pilot hole as a guide, use 1/4" bit to drill a hole from outside through to connect with strike bore. (Fig 3) NOTE: Standard barn door to wall clearance is approximately 3/8" 1" to 1/2". Install additional spacer behind strike faceplate as needed if door to wall clearance is over 1/2". Additional spacers can support maximum clearance of 3/4" between door and wall. (Fig 4) 1-1/4" 1" Ø1/8" Ø1" Fig 2 1/4" Ø1/4" Outside Fig 3 Min 1/2" Max 3/4" Fig 4 Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited. 81056 10/19 3 6. Install Dust Proof Strike with Emergency Release Install 1" dust proof strike with 1/4" release screws on outside. (Fig 1) Cut break-away screw to appropriate door thickness. DO NOT OVER TIGHTEN. (Fig 2) Install break-away screw and tighten with Allen wrench. DO NOT OVER TIGHTEN. Screw on decorative cap by hand. (Fig 3) Use release key, provided with lock set, to push through center hole on release to push lockbolt back and unlock door. (Fig 4) Door Thickness 1-3/8" 1-3/4" Length without Spacer 11/16" 1-1/8" Length with Spacer 15/16" 1-5/16" Fig 1 1-5/16" 1-1/8" 15/16" 11/16" Door Thickness Fig 2 Open Fig 3 Fig 4 ASSA ABLOY Opening Solutions Architectural Accessories Group Memphis, TN 38141 Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited. 81056 10/19pdf-lib (https://github.com/Hopding/pdf-lib) pdf-lib (https://github.com/Hopding/pdf-lib)