User Guide for Edge-corE models including: AS9926-24D, AS9926-24DB, Network Fabric Switch
Avertissement: Pour une installation sûre et fiable, utilisez uniquement les accessoires et les vis fournies avec le AS9926-24D. L'utilisation d'autres ...
– 1 – Quick Start Guide E102020-CS-R02 150200002235A Network Fabric Switch AS9926-24D | AS9926-24DB 1. Network Fabric Switch 2. Rack mounting kit—2 front-post brackets, 2 rear-post brackets,
Quick Start Guide
Network Fabric Switch
AS9926-24D | AS9926-24DB
Package Contents
www.edge-core.com
1
2
3
4
5
6
1. Network Fabric Switch 2. Rack mounting kit--2 front-post brackets, 2 rear-post brackets,
20 screws, and 2 ear-locking screws
3. Power cord
4. Ring lugs (x4) (included with DC PSUs only) 5. Console cable--RJ-45 to DE-9 6. Documentation--Quick Start Guide (this document) and Safety
and Regulatory Information
Overview
1
2
3
5
6
4
7
1. System LEDs
4. Product label
2. 24 x 400G QSFP-DD ports
5. 2 x AC/DC PSUs
3. Management ports: 1 x 1000BASE-T RJ-45, 2 x 10G SFP+,
6. 6 x fan trays
RJ-45/USB console, USB
7. 2 x grounding screws
System LEDs/Buttons
Port LEDs
SYS/LOC: Flashing Amber (switch locator) DIAG: Green (OK), Amber (no OS or fault) FAN: Green (OK), Amber (fault) PSU1/PSU2: Green (OK), Amber (fault) RST (reset) Button
FRU Replacement
QSFP-DD LEDs 400G: 1 LED Blue
SFP+ 10G OOBF LEDs Green (10G) Amber (1G)
RJ-45 MGMT LED Green (link/activity)
PSU Replacement 1. Remove the power cord.
2. Press the release latch and remove the PSU.
3. Install replacement PSU with matching airflow direction.
Fan Tray Replacement 1. Pull the handle release latch.
2. Remove fan tray from the chassis.
3. Install replacement fan with matching airflow direction.
*150200002235A_R02*
1
E102020-CS-R02 150200002235A
Installation
Quick Start Guide
Warning: For a safe and reliable installation, use only the accessories and screws provided with the AS992624D. Use of other accessories and screws could result in damage to the unit. Any damages incurred by using unapproved accessories are not covered by the warranty.
Avertissement: Pour une installation sûre et fiable, utilisez uniquement les accessoires et les vis fournies avec le AS9926-24D. L'utilisation d'autres accessoires et vis pourrait endommager l'appareil. Les dommages causés par l'utilisation d'accessoires non approuvés ne sont pas couverts par la garantie.
Caution: The switch includes plug-in power supply (PSU) and fan tray modules that are installed into its chassis. Make sure all installed modules have a matching airflow direction (front-toback or back-to-front).
Attention: Le commutateur comprend des modules d'alimentation et de modules de ventilation installés dans son châssis. Assurez-vous que tous les modules installés ont une direction d'air adaptée (avant-arrière ou arrière-arrière).
Note: The switch has the Open Network Install Environment (ONIE) software installer preloaded on the switch, but no switch software image. Information about compatible switch software can be found at www.edge-core.com.
Note: The drawings in this document are for illustration only and may not match your particular model.
3. Lock the Rear-Post Brackets Use the included screws to lock the position of the rear-post brackets.
1 Mount the Switch
Caution: This device must be installed in a telecommunications room or a server room. Attention: Cet appareil doit être installé dans une salle de télécommunication ou une salle de serveur.
Optional Slide-Rail Installation An optional slide-rail kit is available for rack installation. Follow the installation procedure provided with the kit.
2 Ground the Switch
1. Attach the Brackets Use the included screws to attach the front- and rear-post brackets.
Verify Rack Ground Ensure the rack on which the switch is to be mounted is properly grounded and in compliance with ETSI ETS 300 253. Verify that there is a good electrical connection to the grounding point on the rack (no paint or isolating surface treatment).
Attach Grounding Wire Attach a lug (not provided) to a #12 AWG minimum grounding wire (not provided), and connect it to the grounding point on the switch rear panel. Then connect the other end of the wire to rack ground.
2. Mount the Switch Mount the switch in the rack and secure it with rack screws.
2
Quick Start Guide
Caution: The chassis ground connection must not be removed unless all supply connections have been disconnected. Attention: Le raccordement à la terre ne doit pas être retiré sauf si toutes les connexions d'alimentation ont été débranchées. Caution: The device must be installed in a restrictedaccess location. It should have a separate protective ground terminal on the chassis that must be permanently connected to a well grounded chassis or frame to adequately ground the device chassis and protect the operator from electrical hazards. Attention: L'appareil doit être installé dans un emplacement à accès restreint. Il doit comporter une borne de terre de protection distincte sur le châssis, qui doit être connectée en permanence à la terre pour assurer une mise à la terre adéquate du châssis et protéger l'opérateur des risques électriques.
3 Connect Power
4 Make Network Connections
QSFP-DD Ports Install transceivers and then connect fiber optic cabling to the transceiver ports. Alternatively, connect DAC or AOC cables directly to the QSFP-DD slots.
5 Make Management Connections
Install one or two AC/DC PSUs and connect them to an AC or DC power source.
Caution: Use a UL/IEC/EN 60950-1 certified power supply to connect to a DC converter. Attention: Utilisez une alimentation certifiée UL/IEC/EN 60950-1 pour le connecter à un convertisseur CC. Caution: All DC power connections should be performed by a qualified professional. Attention: Toutes les connexions d'alimentation CC doivent être effectuées par un professionnel qualifié.
10/100/1000M RJ-45 Management Port Connect Cat. 5e or better twisted-pair cable.
10G SFP+ Management Ports Install transceivers and then connect fiber optic cabling to the transceiver ports.
RJ-45 Console Port Connect the included console cable and then configure the serial connection: 115200 bps, 8 characters, no parity, one stop bit, 8 data bits, and no flow control.
4
1
2
3
1. Use the ring lugs included with the DC PSU. 2. DC return 3. -40 -75 VDC 4. Ground
3
Hardware Specifications
Switch Chassis
Size (WxDxH) 438.4 x 536 x 43.1 mm (17.26 x 21.1 x 1.7 in.)
Weight
10.77 kg (23.74 lb), with 2 PSUs and 6 fans installed
Temperature Operating: 5° C to 40° C (41° F to 104° F) Storage: -40° C to 70° C (-40° F to 158° F)
Humidity
Operating: 5% to 95% (non-condensing)
Power
1300 Watts maximum
Consumption
AC PSU
Input Power Rating
100120 VAC, 5060 Hz, 12 A max. 200240 VAC, 5060 Hz, 7.5 A max. 190310 VDC, 85 A
48 VDC PSU
Power Rating 48 VDC, 1300 Watts
DC Input
-40 V -75 V, 40 A maximum
Regulatory Compliances
Emissions
EN 55032:2015+AC:2016, Class A EN 61000-3-2:2014, Class A EN 61000-3-3:2013 FCC Class A VCCI Class A CCC GB 9254-2008, Class A BSMI CNS13438-1
Immunity
EN 55024:2010+A1:2015 IEC 61000-4-2/3/4/5/6/8/11 EN 55035:2017
Safety
UL (CSA 22.2 No 62368-1 & UL62368-1) CB (IEC/EN60950-1 & IEC/EN 62368-1) CCC GB4943.1-2011 BSMI CNS14336-1
Quick Start Guide
4
AS9926-24D | AS9926-24DB
www.edge-core.com
1
2
3
4
5
6
1. 2. -- 2 2 20
2
3.
4. 4 5. --RJ-45 DE-9 6. --
1
2
3
5
6
4
7
1. LED
4.
2. 24 x 400G QSFP-DD
5. 2 x AC/DC PSUs
3. 1 x 1000BASE-T RJ-452 x 10G SFP+RJ-45/USB 6. 6 x
USB
7. 2 x
LED/
LED
SYS/LOC OK PSU1/PSU2 (RST)
FRU
QSFP-DD LEDs 400G1 LED
SFP+ 10G OOBF LEDs (10G) (1G)
RJ-45 LED /
PSU 1. 2. PSU
3. PSU
1.
2.
3.
1
AS9926-24D
(PSU)
Open Network Install Environment (ONIE) www.edge-core.com
1
3.
1.
2
2.
ETSI ETS 300 253
#12 AWG
Caution: Caution:
2
3
5
/ PSU
UL/IEC/EN 60950-1
10/100/1000M RJ-45 5e
10G SFP+
RJ-45 115200 bps 8 8
4
1
2
3
1. 2. DC 3. -40 -75 VDC 4.
4
QSFP-DD DAC AOC QSFP-DD
3
(WxDxH) 438.4 x 536 x 43.1 mm 17.26 x 21.1 x 1.7
10.77 kg 23.74 2 6
5° C 40° C 41° F 104° F -40° C 70° C -40° F 158° F
5% 95%
1300W
PSU
100120 VAC 5060 Hz 12 A
200240 VAC 5060 Hz 7.5 A
190310 VDC 85 A
48 VDC PSU 48 VDC, 1300 W
-40 V -75 V, 40 A
EN 55032:2015+AC:2016, Class A EN 61000-3-2:2014, Class A EN 61000-3-3:2013 FCC Class A VCCI Class A CCC GB 9254-2008, Class A BSMI CNS13438-1
EN 55024:2010+A1:2015 IEC 61000-4-2/3/4/5/6/8/11 EN 55035:2017
UL (CSA 22.2 No 62368-1 & UL62368-1) CB (IEC/EN60950-1 & IEC/EN 62368-1) CCC GB4943.1-2011 BSMI CNS14336-1
4
AS9926-24D | AS9926-24DB
www.edge-core.com
1
2
3
4
5
6
1. 2. --2 2 20 2
3.
4. (x4) DC PSU 5. --RJ-45 DE-9 6.
1
2
3
5
6
4
7
1. LED
4.
2. 24 x 400G QSFP-DD
5. 2 x AC/DC PSUs
3. 1 x 1000BASE-T RJ-452 x 10G SFP+RJ-45/USB 6. 6 x
USB
7. 2 x
LED
LED
SYS/LOC DIAG (OK) OS (OK) PSU1/PSU2 (OK) (RST)
FRU
QSFP-DD LEDs 400G1 LED
SFP+ 10G OOBF LEDs (10G) (1G) RJ-45 MGMT LED /
PSU 1. 2. PSU
3. PSU
1. 2.
3.
1
AS9926-24D PSU ONIE www.edge-core.com
1
3.
1.
2.
2
ETSI ETS 300 253 #12 AWG
2
3
5
AC/DC PSU AC DC UL/IEC/EN 60950-1 DC DC
10/100/1000M RJ-45 5e
10G SFP+
RJ-45 115200 bps8 1 8
4
1
2
3
1. 2. DC 3. -40 -75 VDC 4.
4
QSFP-DD DAC AOC QSFP-DD
3
x 438.4 x 536 x 43.1 mm (17.26 x 21.1 x 1.7 in.) x
10.77 kg (23.74 lb) 2 PSU 6
5° C 40° C (41° F 104° F) -40° C 70° C -40° F 158° F
5% 95%
1300
AC PSU
100120 VAC5060 Hz 12 A
200240 VAC5060 Hz 7.5 A
190310 VDC85 A
48 VDC PSU
48 VDC, 1300
DC
-40 V -75 V, 40 A
EN 55032:2015+AC:2016, Class A EN 61000-3-2:2014, Class A EN 61000-3-3:2013 FCC Class A VCCI Class A CCC GB 9254-2008, Class A BSMI CNS13438-1
EN 55024:2010+A1:2015 IEC 61000-4-2/3/4/5/6/8/11 EN 55035:2017
UL (CSA 22.2 No 62368-1 & UL62368-1) CB (IEC/EN60950-1 & IEC/EN 62368-1) CCC GB4943.1-2011 BSMI CNS14336-1
4
Acrobat Distiller 11.0 (Windows)