Instructions for PYLONTECH models including: Pelio-L-5.12 WI-FI Set Up Guidance, Pelio-L-5.12, WI-FI Set Up Guidance, Set Up Guidance, Up Guidance, Guidance
File Info : application/pdf, 15 Pages, 1.32MB
DocumentDocument- Pelio-L-5.12 WI-FI Set-up Guidance Instructions Step 1: Install WI-FI Logger ......................................................................................................... 3 Step 2: WI-FI Network Config ..................................................................................................... 4 Step 3: Create Plant .................................................................................................................... 8 Step 4: Add Collector .................................................................................................................. 9 Appendix: Pylontech Home APP User's Guide ........................................................................ 11 2 / 15 Please note You must read this instruction manual carefully before installation to ensure you can install and use your battery correctly. This document describes how to configure Pelio-L-5.12 of the Wi-Fi logger and how to set up the Pylontech Home APP. Step 1: Install Wi-Fi logger 1. With the front of the logger (with the label) facing outwards, insert it into the WI-FI USB port; 2. Rotate the nut on the top of the logger clockwise until the buckle fits into the card slot, then rotate the nut half a turn to lock the WI-FI logger. Logger Button Please note: The white button on the front of the WI-FI logger (Logger Button) is used to trigger some functions of the logger. Short Press (2s~6s): The NET LED flashes fast, logger enters network configuration mode. Long Press (over 10s) Logger restore factory settings, only the STAT LED is on. The NET LED is on, the STAT LED flashes and the COM LED flashes intermittently, indicating that the collector is working normally. Refer to the table below to understand the status of the WI-FI logger indicator LED. LED LED Function Status Description 1. LED off: Indicates that the logger failed to Indicate the communication between the logger and the battery communicate with the battery 2. LED on: Indicates that the communication between the logger and the battery has been successfully established 3. LED fast flash: Indicates that the logger and the battery are communicating. 3 / 15 Indicate logger network communication status 1. LED off: Indicates the logger network connection is abnormal. 2. LED on: Indicates the logger network connection is normal 3. LED fast flash: Indicates the logger enters network configuration mode Indicate the status of 1. LED off: The logger is running abnormally. the logger 2. LED flash: Indicates the logger is running normally. 4 / 15 Step 2: WI-FI Logger Network Configuration Please note Make sure the battery is turned on during network configuration 1. Download `Pylontech Home App'. Download method is given below: a. Search `Pylontech Home' in Google Play/Harmony store or APP Store. b. Scan the QR Code below and download it directly. Android/Harmony QR Code iOS QR Code 2. Open Pylontech Home App, sign up and login. New users can sign up following the steps below (1)(2)(3)(4) If you already have an account, just enter the account and password to login * Organization code defaults to Pylontech. If the distributor provides you with other organization codes, please keep the corresponding codes and fill in the codes when registering an account. The organization code is used to bind the corresponding organization to obtain the after-sales service provided by them. Please note: Make sure the org code is correct. If you have any questions about this, please contact your local distributor for confirmation. Select here to change languages (2) Fill the information If you already have an account, select Login (1)Select Sign up to register (3) After reading the Term of use and Privacy Policy, click the box to agree. 5 / 15 * The default organization code is Pylontech (4) Select Signup to finish registration 3. Wi-Fi logger network configuration Please noteWi-Fi logger only supports 2.4GHz Wi-Fi network5GHz Wi-Fi cannot be connected. (1) Turn on the Bluetooth, Wi-Fi and location services (GPS) of the mobile device. (2) Press the white button on the front of the logger for 2~6 seconds and then release it until the NET indicator on the logger flashes quickly, at this time the logger enters the config network mode (the NET light of the logger is always on during the network config process) . (3) After logging in to the Pylontech Home App, enter the "Me" page and select "Config Network". At this time, the window will automatically pop up "Network Configuration Instructions" (new configuration instructions and screenshots are required), reading this instruction can guide you in network configuration. (4) Select the Wi-Fi network to be configured and enter the corresponding network password. 6 / 15 (5) Enter the S/N of the logger Method 1: Select `Scan' to get the QR code of the WIFI logger Method 2: Type in the SN on the logger manually Method 1 Scan the QR code on Wi-Fi logger Method 2: Select this icon and type in SN manually (6) Select "Start config", the progress will take around 1 minute Type in SN XXXXXXXXXXXXXX WIFI config will take around 1 minute 7 / 15 If network config success, the page will turn to "Config Success" If network config fail, the page will turn to "Config timeout" Note: After selecting `Start Config', if you confirm that the device has exit config network mode (see the first step to confirm the status of the flashing light on the logger), you can click "Close", and re-try the above step (2) then clicking "Start Config". Please note: if the network config fails, please check the following reasons and re-configure the network according to the above steps: Make sure WLAN is ON; Make sure the Wi-Fi network; Check whether the Wi-Fi network password is entered correctly; Make sure the wireless router is not blacklisted; Remove special characters in Wi-Fi network name; Shorten the distance between mobile phone and device, device and router; Try to connect another Wi-Fi network. 8 / 15 Step 3: Create Plant 1. Select"Plants"and enter plant page; 2. Select `more'then select "Create Plant" · Fill in the plant information (* is required information); · Plant Owner:About Plant Owner, please note the following settings: a. Plant Owner name is automatically generated when registering an account. If you want to change the name of Plant Ownerplease do the following steps after "Create Plant" Exit the current page enter the "Me" page Select "Account" Enter your custom name in the "Nick Name" column Select "Confirm and Save" under the current page to complete the modification. b. If you want to reset Plant Owner, expand the right arrow to reset the new owner. Plant visitor: Select Plant Visitoryou can add a plant visitor 3. Select"Finish" on the right-up cornerfinish create plant. 2. Select `more'then select "Create Plant" 3.* are required fields 4.Select"Finish"to finish create plant 1.Select"Plants" To change the Plant Owner*, expand the right arrow to reset the new owner. To add a new plant visitor**, expand the arrow on the right to add a new visitor. * Plant Owner is the owner of the plant and has full access to the plant, including modifying and deleting the plant, as well as managing all visitors to the plant and setting up new owners. ** Plant Vistor is visitor, who has permission to view plant information and add collectors; but does not have permission to delete plants. Please note: You can build multiple plants for different battery systems. If you need to add more power stations, please repeat the above steps. 9 / 15 Step 4: Add Collector · Please note: In order to facilitate your view and manage the information of different batteries in the same system, it is recommended to add their collectors under the same plant. System 1 System 2 System n Plant A Collector a Colletcor b Collector.... Plant B Collector x ... Collector y Collector .... Plant * Collector . Collector.. Collector... 1.Choose one of the following two methods (a or b) to enter the "Add Collector" a. Select "Plants" Select "More" in the upper right corner Select "Add Controller" Select a plant you want to add; b. Select "Plants" Select the plant and expand the arrow on its right side and Select "Add Controller". 1(a) 1(b) 10 / 15 2. Scan the QR code on the front of the Wi-Fi logger or manually enter the SN number of the logger, and Select "Add". 3. After adding, Select "Finish" in the upper right corner to save and exit. 4. The collector was added successfully. 2 3 4 You can continue to select "Add" to add more collectors in the same plant The collector was added successfully 11 / 15 AppendixPylontech Home App user guide 1. Select "Plants" to view the detailed information about the plant you have added. a. Select the plant you want to view, and select the arrow on the right to display all battery information connected to the power station. b. To view battery detailed information, you can expand its arrow to display including battery basic information, charging/discharging parameters and status. a b Click "Plant" to view the basic information of all connected batteries 12 / 15 NoteFor battery information, please refer to the following table: Basic Information Charge & Discharge Status Cell Data (Cell 1~n) Wi-Fi SN Product SN BMS version Current(A) Voltage (V) Remain Capacity (Ah) Module Capacity (Ah) Cycle number Total Charge Capacity (Ah) Total Discharge Capacity (Ah) Charge current recommend(A) Discharge current recommend(A) Temperature of BMS(°C) Total Pressure Overvoltage Single Core Undervoltage Total Voltage Under voltage Charging Over Temperature Discharge Over Temperature Discharge Overcurrent Charging Overcurrent Voltage (V) Temperature (°C) SN (serial number) of Wi-Fi logger SN (serial number) of BMS Version of BMS software Current of the battery during its working status Voltage of the battery Remain capacity of the battery Total capacity of the battery module Cycle count of the battery that has used Total charge capacity of the battery Total discharge capacity of the battery Recommended charge current for the battery Recommended discharge current for the battery Temperature of the BMS module It will display "Y" if the described status is triggered; otherwise it will display "-". Voltage of the single cell Temperature of the single cell 13 / 15 2. You can give us feedback by submitting "Tickets" on: a. Product Advisory b. System Issue Select"+" to submit a ticket *are required information In Description, you can enter a brief description of the problem; In Attachments you can add attachments (such as photos) as a supplement. Select "Tickets" to upload a feedback Choose the ticket type Select "save" to submit the ticket 3. Select "Overview" to view the operation status of your plant (can be viewed by Day/Month/Year/Total) Remain Capacity (%) Total Discharge Capacity(Ah) Estimated Carbon Emissions Reduction (G) Note The above overview information is described as follows: Taking the above diagram as an example, "54%" is the remaining capacity of the battery (%); "204Ah" is the total discharge capacity of the battery (Ah); "203.39 G" is the estimated carbon emission savings (G). The chart shows charged power of the battery in a specific period (day/month/year/total); the horizontal axis shows the time period you selected, and the vertical axis corresponds to the charged power of the battery in this period. 14 / 15 4. Select "Events" to view the alarms or faults that the system detects when the battery is abnormal. Please contact the after-sales service to solve it. 5. Select `me' and you can log out of the current account or reconfigure a new device. 4. Select "Events" to view the alarms or faults of the battery 5. Click "Me" to view the basic information and settings of the current account 15 / 15Microsoft Word 适用于 Microsoft 365