IDEAL
Willkommen bei Krug + Priester I krug-priester.com
Instruction Manual for IDEAL models including: 8741119, 2A3QI-8741119, 2A3QI8741119, AP60 PRO Air Purifier, AP60 PRO, AP80 PRO, Air Purifier
Krug und Priester GmbH Co KG 8741119 Air Purifier 2A3QI-8741119 2A3QI8741119 8741119
File Info : application/pdf, 25 Pages, 1.66MB
DocumentDocumentLuftreiniger www.ideal.de
EN 25
Thank you for choosing a device from IDEAL. · The device is used exclusively for cleaning the ambient air indoors. · Please read these operating instructions before starting to use the device
and please follow the safety instructions. The operating instructions must be kept available with the device at all times. Read and save these instructions: to persons associated with use of the appliance. · Only use the device indoors. · Only use a wall socket that supplies the correct voltage (see rating plate). · Do not modify or repair the device. · Do not use the device if the power cable or mains plug is damaged or if the connection at the wall socket is not stable. · Make sure that the power cable does not get crushed while you are using the device and that it cannot be damaged in any other way. Place the cable so that no one will trip over it. Do not place the power cable under strain. · Disconnect the plug from the wall socket for cleaning purposes, before time. · Do not touch the plug or the device if you have wet hands. · Keep packing material, such as plastic wrapping, away from children! (Risk of suffocation) · Place the device at least 10 cm away from the wall. · Keep the device away from areas subjected to draft (wind). · Make sure that furniture, fabrics or other objects do not come in contact with the air intake/outlet or block them. · Place the device on a stable, even surface and make sure there is · Do not spray any insect repellent. · Do not use in rooms where the device may come into contact with fuel vapour or metal dust. · Do not use any volatile liquids, petroleum, kerosene, paint thinner or polishing paste to clean the device. Such liquids may damage the surface of the device. · Do not expose the device to rain, water, moisture or high humidity, and do not set it up in a bathroom or kitchen next to a sink. · Make sure that no foreign objects get into the outlet grilles. · The device is not suitable for removing harmful gases (carbon monoxide, e.g. from heating appliances). · The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
26
· Children being supervised not to play with the appliance. · Do not block the air intake and outlet.
technical parameters. Improper usage may pose a threat to life and health. · Disconnect the mains plug prior to any cleaning or maintenance work.
· Do not use any solvents. These could damage the housing surface. · Do not use any substances containing silicone, since this could destroy the
air quality sensor. · Do not test the effectiveness of the air quality sensor with high quantities of
gas, or alcohol, since this could destroy the air quality sensor. · Clean the textile cover with a vacuum cleaner. · If necessary, the textile cover can also be washed by hand (please refer to
the care instructions on the label). · WARNING: Chemical Burn Hazard. Keep batteries away from children. · This product contains a lithium button/coin cell battery. If a new or used
lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Risk of injury due to electric shock. Always disconnect the mains plug prior to: · Carrying out maintenance work or cleaning · Moving the device · Do not use any spray cans with flammable content near to the
27
· needs to be replaced.
· ·
·
Luft reiniger w ww .ideal.de
· With self-adhesive · With 3V lithium battery
28
· The air intake ducts on the top can be used as handles (see adjacent diagram).
· Place the device at least 10 cm away from the wall. · Keep the device away from areas subjected to draft (wind). · Make sure that furniture, fabrics or other objects do not come in contact with the air intake/
outlet or block them. Take out the power cable ( ), operating instructions ( ) and remote control ( with
Remove top packaging tray. Grasp the lift it out of the box.
5.
7. 6.
8.
Please remove and dispose the self-adhesive tape ( Transport safety). The front panel is hooked from below at two ends and is kept closed by totally 4 magnets.
) and then swing it downwards ( ). Remove the single piece of cardboard ( Transport safety). Remove the front panel ( ).
29
7. 8.
14. 13.
9.
using the recessed grips provided and turn it anti-clockwise ( ).
) and remove ).
the notches provided and lock in position by turning clockwise ( ).
), then pivot upwards and press shut ( ). ( ), then to the socket ( ). Note: Use the original packaging to store the air protect the activated carbon.
Safety information protective covers (motor protection grille, ventilation outlet grille, door, etc.) fully and securely attached is not permitted.
30
Air intake ducts
Air outlet grill Control panel
Filter cartridge
Front panel
Power cable
31
A On/off button
B Fan speed button
E Air quality indicator
C Timer button
D Quiet button
F Filter replacement
indicator
Fan speed indicator
Timer indicator
J Daylight sensor
L Air quality sensor
K IR receiver
Quiet indicator
The air quality sensor (L
A) and after being
disconnected from the mains power supply. Once the air quality sensor has been calibrated, the
(F) and air quality indicators (E) flash red alternately.
M Dust sensor 32
A On/off button
B Fan speed button
E Air quality indicator
C Timer button
D Quiet button
F Filter replacement
indicator
Fan speed indicator
Timer indicator
J Daylight sensor
L Air quality sensor
K IR receiver
Quiet indicator
· Press the on/off button (A . In automatic mode, the fan speed ( ) automatically
adapts to the measured air quality. The worse the air quality, the higher the fan speed. · Press the fan speed button (B
fan speed . Press again to increase the fan speed to . Press again to increase the fan speed to , or to the turbofan speed . maximum capacity. This can only be selected manually.
after the
A).
· Press the timer button (C) to activate the timer. Press repeatedly to increase the timer time:
(h)
. Each number lights up in turn. Press the timer button again (no number
lights up) to disable the timer function.
· The timer indicator counts the respective time with ( Countdown). The remaining time is
displayed.
33
A On/off button
B Fan speed button
E Air quality indicator
C Timer button
D Quiet button
F Filter replacement
indicator
Fan speed indicator
Timer indicator
J Daylight sensor
L Air quality sensor
K IR receiver
Quiet indicator
The Quiet button (D) is provided for particularly low-noise, unobtrusive operation (e.g. bedrooms). Press the Quiet button (D) to switch the fan speed ( ) to its lowest capacity and switch off all indicators. Only the Quiet indicator ( ) is dimly lit.
The air quality is displayed in 3 colours: Green: good air quality Yellow: average air quality Red: poor air quality
An illuminated red "
The display brightness is automatically adjusted to the ambient light. Receives the signals from the remote control.
34
· Always use 3V lithium batteries CR2025 for the remote control. · Incorrect battery usage may result in leakage of battery fluid and/or damage. · If the remote control is not going to be used for a long time, please remove the battery.
· Make sure that no objects or furnishings are situated between the remote control and the
· Locations where fluorescent tubes are flickering because they are defective or old. · Do not store the remote control in direct sunlight and/or close to radiators/heaters. ·
The remote control has a pre-installed lithium
battery CR2025.
to
activate the remote control battery.
K).
35
B
A
C
· Open the battery compartment by pressing (A) and pulling out (B) at the same time. Take out the flat battery.
· Insert a new battery into the battery compartment, making sure the polarity is correct (+ / -).
· Always use 3V lithium batteries CR2025. · Slide the battery compartment back into its
seating (C).
The remote control comes with a self-
D
D). If required, this
can be stuck on the back of the remote
remote control can easily be attached to any ferromagnetic surface
Batteries must NOT be disposed of with household waste. As the user, you are legally obligated to return used batteries for proper disposal. You can hand in your batteries at public collection points in your community or wherever the same type of batteries are sold. · It is very important that you make sure that the polarity of the batteries is correct. · Batteries that are leaking fluid are dangerous. Only touch these with suitable gloves. · Keep batteries out of the reach of children.
period of time. · The cells shall be disposed of properly, including keeping them away from children. · Even used cells may cause injury.
36
P On/off button O Automatic button
Q Quiet button
N Fan speed buttons
Turbo Auto 8h
3
4h
2
2h
1
1h
R Timer buttons
S Locking button
Select the required fan speed .
.
P
.
.
Select the required timer time .
Press the locking button
Press the locking button again to unlock.
pressing and holding down the on/off button (A) on the device.
Note: When you operate the remote control, the air quality indicator (E) lights up for approx. 1 second
function is activated, the air quality indicator (E) lights up briefly in red.
A On/off button
E Air quality indicator
37
1.
4. 5.
F, see page 34)
2. 3.
6.
The front panel is hooked in at the bottom in two places, and kept shut with 4 magnets. Open the front panel from the top and hold ( ), pivot downwards ( ) and take off ( ). using the recessed grips provided and turn it anti-clockwise ( ).
). Remove the ).
7.
in the notches provided and lock in position by
turning clockwise ( ).
),
then pivot upwards and press shut ( ). Connect
9.
), then to
the socket ( ).
10.
11. 8.
38
smartphone/tablet (iOS /Android). E Air quality indicator
D Quiet button
Press and hold down the Quiet button (D) until the air quality indicator (E) flashes The WLAN is enabled when the air quality indicator (E) flashes blue The WLAN is disabled when the air quality indicator (E) flashes white.
Press and hold down the Quiet button (D), plug in the power cable and continue to hold down the Quiet button (D) until the air quality indicator (E) flashes pink
The WLAN is reset to factory settings. Note: smartphone/tablet should be maintained during setup (connection setup).
39
F, page 34) lights up.
· Clean the control panel with a dry, lint-free cloth. · Clean the openings for the air quality sensor (L) and the dust sensor (M page 32) with a
vacuum cleaner.
cartridge ("
" page 38).
· Do not use any solvents. These could damage the housing surface, the control panel and the
air quality sensor.
· Do not use any substances containing silicone, since this could destroy the air quality sensor. · Do not test the effectiveness of the air quality sensor with high quantities of gas, or alcohol,
since this could destroy the air quality sensor.
You can source accessories via your dealer or at
.
Wall mount Trolley
40
Order no. 8741 001 Order no. 8741 002
Make sure that the power cable is not damaged in any way. Check both ends of the power cable. Make sure that these are plugged in and that the (page 30).
cartridge is inserted.
in place with all 3 tabs and is fully locked
(
, page 30).
Disable the locking function on the remote
control (
, page 37).
Unplug the power cable and then plug it back in.
Check the battery (3V lithium CR2025). Clean the IR receiver with a dry, lint-free cloth.
(page 35). Having joined the power cord or remote control is blocked for about 10 seconds
41
on/off button (A, page 32). Disable the Quiet function by pressing the Quiet button (D, page 34).
Wait until the calibration process
(see
, page 32) has been completed
(this may take a few minutes)
Clean the openings for the air quality sensor L, dust sensor M (page 32), the air intake ducts and the interior of the air located) with a vacuum cleaner.
Calibrate the air quality sensor by briefly disconnecting it from the mains again!
becomes saturated and reliable
of the odours. fan speed (page 33).
42
Place the device on an even surface. Use the fan speed button (B, page 33) to set a lower fan speed ( , page 33). Clean the relevant section on the control panel (J, page 32)! The display intensity automatically adapts to its surroundings.
Service
Contact: Service · ·
43
Power supply Power consumption Suitable for rooms Air flow rate (max.) Dimensions (L × W × H) Weight Volume at turbofan speed (max.) Volume in Quiet mode (min.)
Power supply Power consumption Suitable for rooms Air flow rate (max.) Dimensions (L × W × H) Weight Volume at turbofan speed (max.) Volume in Quiet mode (min.)
Subject to technical changes.
200-240V 50/60Hz / 100-120V 50/60Hz 90W (200-240V) / 75W (100-120V) 50 to 70 m² * 600 m³/h 468 × 275 × 668 mm 15 kg 56,6 dB(A) 16,5 dB(A)
200-240V 50/60Hz / 100-120V 50/60Hz 175W (200-240V) / 180W (100-120V) 70 to 90 m² * 750 m³/h 468 × 275 × 668 mm 15 kg 63,4 dB(A) 18,7 dB(A)
* For a room height of 2.50 m
44
The company Krug + Priester has the · Quality management system according to
DIN EN ISO 9001:2015 · Environmental management system
according to DIN EN ISO 14001:2015 · Energy management system according to
DIN EN ISO 50001:2018
IDEAL provides a warranty for this device from the date of purchase. · If a material or design defect occurs during the warranty period, IDEAL shall repair or replace
the device, or repay the purchase price, at its discretion. the claim under warranty is made within the warranty period. · The warranty does not cover wearing parts or parts that need to be replaced regularly. · The warranty shall be void if the device is not set up, adjusted and cleaned/maintained correctly (in accordance with the operating instructions). · The warranty shall be void if the device is connected to a power supply that does not comply with the rating plate data.
You can source spare parts via your dealer or at
.
This also applies if you have a defective power cable. Any attempt by untrained persons to perform repairs may pose considerable risk to the user and invalidate the warranty. This device must not be disposed of with household waste! Please hand this device in at the collection points provided! Collecting and recycling electrical and electronic waste conserves valuable resources! The packaging material can be recycled. Dispose of the packaging in an environmentally friendly manner and take it to the recyclable waste collection.
45
This machine is GS-tested and conforms to the following EC guidelines: · 2014/35/EU for electrical safety · 2014/30/EU for electromagnetic compatibility. · 2011/65/EU, 2015/863/EU RoHS. machine. Subject to technical changes.
- Herewith we declare that Made in Germany Made in Germany
- complies with the following provisons applying to it Low voltage directive RoHS directive EMV Electromagnetic compatibility directive - Applied harmonised standards in particular
09.02.2022 Date
- Managing Director -
Authorized representative for technical documentation: Krug & Priester GmbH & Co. KG Simon-Schweitzer-Str. 34 D-72336 Balingen (Germany)
46
Supplier`s Declara on of Conformity 47 CFR § 2.1077 Compliance Informa on
This device complies with part 15 of the FCC Rules. Opera on is subject to the following two condi ons: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera on.
Manufacturer:
KRUG + PRIESTER GMBH & CO KG Simon-Schweitzer-Straße 34 72336 Balingen, Germany
U.S. Responsible Party:
MBM Corpora on 3134 Industry Drive North Charleston SC, 29418 Tel: 843-552-2700 Mail: info@mbmcorp.com
Trade Name:
IDEAL
Models:
AP 30/ 40/ 60/ 80/ 140 PRO
Classi ca on:
FCC Part 15B
We herby declare, that the equipment bearing tradename and model number speci ed above was tested conforming to the applicable FCC rule part(s) 15B and the most accurate measurement standards. We con rm that the necessary steps have been taken and are in force to assure that the produc on units of the same equipment will con nue to comply with the Commission's requirements.
Krug + Priester GmbH & Co KG
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec on against harmful interference in a residen al installa on. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc ons, may cause harmful interference to radio communica ons. However, there is no guarantee that interference will not occur in a par cular installa on. If this equipment does cause harmful interference to radio or television recep on, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separa on between the equipment and receiver. --Connect the equipment into an outlet on a circuit di erent from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help.
To ensure compliance with FCC and ISED RF exposure requirements this device must be installed to provide a minimum of 20cm between the device and people.
47
Krug & Priester GmbH & Co. KG Simon-Schweitzer-Str. 34 D-72336 Balingen (Germany) www.krug-priester.com
9700285 01-2018 09.02.2022 zm