GERWIN Tubular Motor Gateway Operation Guide

Operation Guide

1. Programming

Note: The setting key on the back of the remote control is P2. The motor setting key is P1.

Steps:

1. Power on the device within 10 seconds OR press the motor P1 key once.
2. Press the P2 key once.
3. Press the P2 key again.
4. Press the UP key once.
5. Confirmation: "OK" is displayed. Code matching is successful.

2. Limit Setting

Steps:

1. Enter limit setting mode: Press P2 once.
2. Run to the desired position for the Up limit.
3. Set Up limit: Press P2 once, then press UP or DOWN once.
4. Confirmation: "OK" is displayed. Up limit setting is successful. The motor rotates up and down once.
5. Run to the desired position for the Down limit.
6. Set Down limit: Press P2 once, then press UP or DOWN once.
7. Confirmation: "OK" is displayed. Down limit setting is successful.

Alternative method for setting: Press P2 for 3 seconds or 5 times (press once every 1 second).

3. Limit Fine Adjustment

Steps:

1. Enter the fine adjustment limit setting: Press the setting key for 5 seconds.
2. Adjust the limit point using the UP/DOWN keys.
3. Confirmation: Stroke fine adjustment is successful.

4. Delete Limit

Steps:

1. Press P2 once.
2. Press the DOWN key once.
3. Confirmation: "OK" is displayed. Delete limit is successful.

Alternative method for deleting: Press the "stop" key for 5 times or press the "stop" key for 3 seconds.

5. Add Emitter

Note: Emitter "A" is a coded emitter, Emitter "B" is an uncoded emitter.

Steps:

1. To add coded emitter: Press P2 of the transmitter "A" twice.
2. To add uncoded emitter: Press P2 of the transmitter "B" once.
3. Confirmation: "OK" is displayed. Add "B" emitter is successful.

6. Delete Emitter (Single and Total Deletion)

Steps:

1. For single deletion: Press P2 of the emitter "A" twice, then press P2 of the coded emitter once.
2. For deleting emitter "B": Press P2 of the emitter "B" once. Confirmation: "OK" is displayed. Emitter "B" delete is successful.
3. For total deletion: Press P2 of the coded emitter once. Confirmation: "OK" is displayed. All emitters deleted.

7. Deadman Setting

Steps:

1. Press P2 once.
2. Press the UP key once.
3. Press the DOWN key once.
4. Confirmation: "OK" is displayed. Deadman Setting is successful.

8. Change Direction

Press the setting key. The motor will rotate forward and backward twice, and the change direction is successful.

9. Restore Factory Settings

Press the setting key. The motor will rotate forward and backward for four times, and the factory setting will be restored.

10. Title Movement

Use the title movement emitter.

FCC Compliance Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Warning:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note on Interference:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Limits:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

TUYA Smart App Integration

Download APP

Scan the QR code below and download the TUYA smart app.

Note: Please register the TUYA account with your mobile phone number to facilitate the binding of Mijia and Tmall Genie.

App Setup Steps:

1. Gateway Setup: Press and hold the gateway setting key. Release your hand after hearing the voice prompt "Please release". The gateway will enter the distribution network mode.
2. Add Device in App: Open the "TUYA APP" and click the "+" icon on the upper right to add a device.
3. Device Found: Find the device. Wait for the "multi-function gateway" to pop up, then click "Add".
4. Network Success: Wait for the distribution network to succeed.

The system supports both Zigbee and Tuya platforms.