Welcome to RABLegal - RAB Lighting
Instructions for RAB Lighting models including: R4R89FA120WS Adjustable Recessed Retrofit and Gimbal Retrofit, R4R89FA120WS, Adjustable Recessed Retrofit and Gimbal Retrofit, Recessed Retrofit and Gimbal Retrofit, Retrofit and Gimbal Retrofit, and Gimbal Retrofit, Gimbal Retrofit, Retrofit
File Info : application/pdf, 3 Pages, 7.61MB
DocumentDocumentINSTRUCTIONS FA and end users to save energy. We'd love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com R4R89FA120WS R4R89FA120WB R4R109FA120WB IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. WARNINGS: · Risk of electrical shock. Disconnect power at fuse or circuit breaker before installing or servicing. · To prevent early lamp failure, lamp should only be installed in operating environments ranging between-30 and +40 (-22°F and+104°F). · No user serviceable parts inside. To avoid electrical shock do not disassemble product. · · · Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation · To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. · Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder terminals, Instead installers should cut existing lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by employing applicable connectors. · by authorities having jurisdiction. · This device is not intended for use with emergency exits. · This retrofit kits suitable for wet locations luminaires specified as belowType Non IC; Type IC; Covered ceilingUncovered ceiling. Installers should examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance. INSTRUCTIONS FA and end users to save energy. We'd love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com WHAT'S IN THE BOX THIS LUMINAIRE HAS BEEN MODIFIED TO OPERATE LED LAMPS. DO NOT ATTEMPT TO INSTALL OR OPERATE INCANDESCENT LAMPS IN THIS LUMINAIRE REPLACE ONLY WITH RAB Lighting Inc. RABLIGHTING.COM 888 722-1000 MODEL# Downlight (1) E26 Adaptor (1) Lumi Sticker (1) INSTALLATION INSTRUCTIONS 1. Make sure the power is turned off at the source to the recessed housing that you are installing the fixture in. Remove existing trim and CFL or Incandescent bulbs. 2. Screw the E26 adapter into the socket inside the housing. (Fig. 2) Fig: 2 TOOLS NEEDED 4" housing. No tools are necessary for installation. MIN.LUMINAIRE DIMENSION Fig: 1 3. Select desired CCT level using switch on driver box. (Fig. 3) Fig: 3 3-15/16" OPTIONAL ACCESSORIES 4. Plug E26 base cable connection into the recessed housing. (Fig. 4) Fig: 4 Goof ring RFLED-GOOF-4R-6R-W For use with 4" housing applications 5. Fig: 5 friction clips into the housing. (Fig. 5) INSTRUCTIONS FA and end users to save energy. We'd love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com INSTALLATION INSTRUCTIONS (cont'd) (Fig. 6) Fig: 6 DIMENSIONAL DRAWINGS R4R89FA120WS 3" R4R109FA120WB 3 3/16" 2 13/16" 2 1/2" 3 15/16" R4R89FA120WB 5 5/16" 3" 3 15/16" 5 5/16" 2 1/2" 3 15/16" 5 5/16" © 2022 RAB LIGHTING Inc. Cranbury, New Jersey 08512 USA R4RX9FA-IN-0722 Easy Answers rablighting.com Visit our website for product info Tech Help Line Call our experts: 888 722-1000 e-mail Answered promptly - sales@rablighting.com RAB WARRANTY: RAB's warranty is subject to all terms and conditions found at rablighting.com/warranty. Free Lighting Layouts Answered online or by request