Adjustable Bed Frame

ADVISORY

Attention: Read the following information before using this product. Use of a surge protector is recommended.

WARNING:

Do not open or tamper with the transformer, control box, motors, or remote control (with the exception of battery compartments).

SMALL CHILDREN AND PETS:

Immediately dispose of all packing materials as they smother small children and pets. Do not allow any persons or pets under the bed. Children should not operate the bed without adult supervision.

HOSPITAL OR CONVALESCENT USE DISCLAIMER:

Adjustable beds are designed and engineered for a lifestyle of in-home comfort and are not intended for hospital use or for a bed-ridden patient on an extended recovery. Adjustable beds are not equipped with bars to help patients get safely in and out of bed and are not intended to be used around tent-type oxygen therapy or explosive gases.

PRODUCT RATINGS:

The bed lift motors are not designed for continuous use of more than 2 minutes in an 18-minute period, or approximately 10% duty cycle. Any attempt to circumvent or exceed this rating will shorten the life expectancy of the product.

WEIGHT LIMIT:

The limitation is 750lb. The bed will structurally support these weights, provided it is evenly distributed across the head and foot sections. This product is not designed to support or lift this amount in the head or foot section alone. Exceeding this weight restriction could damage the bed and/or cause injury. Enter or exit the bed in a flat position and do not sit on the head or foot sections while in the raised position.

LIFTING AND LOWERING MECHANISMS:

It is normal for the raising and lowering feature on this bed to emit a minimal humming sound during operation.

CORD MAINTENANCE:

Always unplug the base from the electrical outlet before cleaning or servicing the base. If the cord or plug is damaged, discontinue use of the bed base and contact qualified service personnel for examination and repair. Make sure the base is in a flat position, and the vibrating motors are off before unplugging from the power source.

SETUP and INSTALLATION

Important: We strongly recommend two able-bodied adults setup and assemble this product.

Step 1

Check to verify all parts are included before discarding any packing materials. All electronics and components that need to be installed are located in boxes under the base or attached to the frame.

Parts List:

Step 2

With the help of your able-bodied assistant, place the carton on the floor.

Step 3

Extend the input power cord (A) and plug it into the transformer power supply (B). Connect the transformer power supply (B) to the control box. The control box is the black box attached to the bottom of the bed.

[Image description: Diagram showing the input power cord (A) connecting to the transformer power supply (B), which then connects to the control box (B).]

Step 4

1. Flip the product over so the back is facing up. The side rails that are folded are at the foot section.
2. Unfold the folded rails on both sides and press them firmly against the Velcro.
3. Align the bottom foot rail upright and press it firmly against the Velcro.

[Image description: Three images showing the process of unfolding the bed frame rails and securing them with Velcro.]

Step 5

• Install the six legs (C) firmly into the base of the frame. Screw the legs into the threaded holes on each corner of the adjustable base frame.
• Do not over tighten.

[Image description: Two images showing the adjustable bed frame upside down with legs being screwed into the base. A close-up shows a leg being screwed in.]

Step 6

Synchronize the remote control (D) with the control box. First, make sure batteries are in the remote control (D). Find the black box mounted under the bed and locate the red circle indicating the button on the control box. Hold the button on the control box for 3 seconds after plugging in the adjustable bed; the light will flash quickly. Then press any key on the remote control (D). When the light stops flashing, the match is successful.

[Image description: Figure 4 shows the remote control with batteries inserted. Figure 5 shows the control box with a red button.]

Step 7

For safety reasons, lifting the adjustable bed frame must be performed by two (2) people. The bed should always be in a flat position before operation. Excessive pressure may damage the legs. Remove all protective plastic covering. Note: Check to make sure that all power cords are clear and do not interfere with any Adjustable Bed Mechanisms.

[Image description: Three images illustrating two people lifting and positioning the adjustable bed frame.]

Step 8

Note: Get the Mattress Retainer Bar (E) from packaging. Carefully insert the mattress retainer bar (E) into the 2 holes on the foot end of the bed base.

[Image description: A person inserting the mattress retainer bar into the holes at the foot of the bed base.]

Step 9

Plug in the adjustable base. You are ready to enjoy!

Remote Control

[Image description: A remote control with numbered buttons: 1 (up arrow), 2 (down arrow), 3 (up arrow), 4 (down arrow), 5 (flat symbol).]

Head Position Adjustments (1, 2)

Press and hold the button to raise or lower the head section of your base.

Foot Position Adjustments (3, 4)

Press and hold the button to raise or lower the foot section of your base.

Flat (5)

Press this button to return the power base to a flat position. NOTE: Make sure your base is in a flat position before using it. Press the FLAT button on the remote control after plugging in the power cord.

TROUBLESHOOTING

Technical Support

(909)637-7665 | (909)637-7593

Other Info

HJ-Customer-Service@outlook.com

Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don't hesitate to contact us.