Reolink Argus PT Operational Instructions

Company Information

REOLINK INNOVATION LIMITED
FLAT/RM 705 7/F FA YUEN COMMERCIAL BUILDING 75-77 FA YUEN STREET MONG KOK KL HONG KONG

EU Representative: Product Ident GmbH, Hoferstasse 9B, 71636 Ludwigsburg, Germany (prodsg@libelleconsulting.com)

UK Representative: APEX CE SPECIALISTS LIMITED, 89 Princess Street, Manchester, M1 4HT, UK (info@apex-ce.com)

Camera Introduction

This section details the components of the Reolink Argus PT camera.

• Status LED: Indicates the camera's operational status.
• Lens: Captures video footage.
• Built-in PIR Sensor: Detects motion based on infrared radiation.
• Daylight Sensor: Adjusts camera settings based on ambient light.
• Built-in Mic: Captures audio.
• Speaker: Outputs audio.
• Reset Hole: A button to restore the camera to factory settings. Press with a pin.
• Micro SD Card Slot: For local video storage. Located near the lens.
• Micro USB Port: For charging the battery.
• Battery Status LED: Indicates battery charge level.
• Antenna: For WiFi connectivity.
• Power Switch: Turns the camera on or off.

Status LED Indicators:

• Red Light [red-light]: WiFi connection failed.
• Blue Light [blue-light]: WiFi connection succeeded.

Power Switch Status:

• Blinking: Standby status.
• On: Working status.

Set up the Camera

Set up the Camera on the Smartphone

Step 1: Download the Reolink App. Scan the provided QR code [qr-code] to download the app from the App Store or Google Play store.

Step 2: Turn on the power switch [power-switch] to power on the camera.

Step 3: Launch the Reolink App. Tap the `[add-button]` icon in the top right corner to add the camera. Scan the QR code on the device and follow the on-screen instructions for initial setup.

Set up the Camera on PC (Optional)

Step 1: Download and install the Reolink Client software.

Step 2: Launch the Reolink Client. Tap the `[add-button]` icon, input the camera's UID code, and follow the on-screen instructions for initial setup.

Charge the Camera

It is recommended to fully charge the battery before mounting the camera outdoors.

Charging Methods:

• Charge the battery with a power adapter (not included).
• Charge the battery with the Reolink Solar Panel (not included if only the camera is purchased).

Charging Indicator:

• Orange LED [orange-led]: Charging.
• Green LED [green-led]: Fully charged.

For optimal weatherproof performance, ensure the USB charging port is covered with the rubber plug after charging.

Install the Camera

General Installation Guidelines:

• For outdoor use, the camera MUST be installed upside down to ensure better waterproof performance and PIR motion sensor efficiency.
• Install the camera 2-3 meters (7-10 ft) above the ground. This height maximizes the PIR motion sensor's detection range.
• For optimal motion detection, install the camera at an angle.

Note: If a moving object approaches the PIR sensor vertically, the camera may fail to detect motion.

Diagram Description: A diagram illustrates mounting height (2-3 meters) and PIR detection distance (2-10 meters), showing an angled installation.

Mount the Camera to the Wall

Step 1: Drill holes according to the mounting hole template and screw the security mount to the wall. Use drywall anchors if needed.

Step 2: Install the antenna to the camera.

Step 3: Screw the camera to the security mount and adjust its direction. For better WiFi connection, it is recommended to install the antenna upward or horizontally.

Mounting Options

Mount the Camera to Ceiling

Step 1: Pull the button on the security mount and unscrew the bracket to separate the two parts.

Step 2: Install the bracket to the ceiling.

Step 3: Align the camera with the bracket and turn it clockwise to lock it in position.

Install the Camera with Loop Strap

The camera can be strapped to a tree using the security mount and ceiling bracket. Thread the provided strap through the plate, fasten it to a tree, and then attach the camera to the plate.

Safety Instructions of Battery Usage

The camera is designed for motion event recording and remote live viewing, not for continuous 24/7 operation at full capacity or constant live streaming.

1. The battery is built-in and cannot be removed.
2. Charge the rechargeable battery using a standard DC 5V/9V battery charger or a Reolink solar panel. Do not use solar panels from other brands.
3. Charge the battery between 0°C and 45°C (32°F to 113°F). Use the battery between -20°C and 60°C (-4°F to 140°F).
4. Keep the USB charging port dry, clean, and free of debris. Cover the port with the rubber plug after charging.
5. Do not charge, use, or store the battery near ignition sources like fire or heaters.
6. Do not use the battery if it exhibits odor, excessive heat, discoloration, deformation, or any other abnormality. If such issues occur during use or charging, immediately turn off the power switch or remove the charger and stop using the battery.
7. Dispose of used batteries according to local waste and recycling laws.

Troubleshooting

Camera is not Powering on

If the camera is not powering on, try these solutions:

• Ensure the power switch [power-switch] is turned on.
• Charge the battery with a DC 5V/2A power adapter until the green light [green-led] indicates a full charge.

If problems persist, contact Reolink Support.

Failed to Scan QR Code on the Phone

If the camera cannot scan the QR code on your phone, try these solutions:

• Remove the protective film from the camera lens.
• Wipe the camera lens with a dry paper or tissue.
• Adjust the distance between the camera and the mobile phone to allow the camera to focus.
• Try scanning the QR code in sufficient lighting.

If problems persist, contact Reolink Support.

Failed to Connect to WiFi During Initial Setup Process

If the camera fails to connect to WiFi, try these solutions:

• Verify that the correct WiFi password has been entered.
• Move the camera closer to your router for a stronger WiFi signal.
• On your router interface, change the WiFi network encryption method to WPA2-PSK/WPA-PSK.
• Change your WiFi SSID or password. Ensure the SSID is within 31 characters and the password is within 64 characters.

If problems persist, contact Reolink Support.

Specification

Video

• Field of View: 105° diagonal
• Night Vision: Up to 10m (33 ft)

PIR Detection & Alerts

• PIR Detection Distance: Adjustable up to 10m (33ft)
• PIR Detection Angle: 90° horizontal
• Audio Alert: Customizable voice-recordable alerts.
• Other Alerts: Instant email alerts and push notifications.

General

• Operating Temperature: -10°C to 55°C (14°F to 131°F)
• Size: 98 x 112 mm
• Weight (Battery included): 470g (16.5 oz)

For more specifications, visit the Reolink official website.

Notification of Compliance

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) the device must not cause harmful interference, and (2) it must accept any received interference, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF warning statement: The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

Simplified EU Declaration of Conformity

Reolink declares that this device complies with the essential requirements and other relevant provisions of Directive 2014/53/EU.

Correct Disposal of This Product

This marking indicates that the product should not be disposed of with other household waste throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased for environmentally safe recycling.

Limited Warranty

This product comes with a 2-year limited warranty, valid only if purchased from the Reolink Official Store or an authorized reseller.

Note: If you are not satisfied with the product and plan to return it, it is strongly suggested to reset the camera to factory default settings and remove the inserted SD card before returning.

Terms and Privacy

Use of the product is subject to agreement with the Terms of Service and Privacy Policy available at reolink.com. Keep out of reach of children.

End User License Agreement (EULA)

By using the Product Software embedded on the Reolink product, you agree to the terms of this End User License Agreement ("EULA") between you and Reolink.

ISED Radiation Exposure Statement

This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

OPERATING FREQUENCY

(the maximum transmitted power)

• 2412MHz-2472MHz (18dBm)
• 5180-5240MHz (16.09dBm)
• 5745-5825MHz (14.47dBm)