2007 - 2011 Honda CR-V Rear Barrier Divider Net Installation

NOTE: Many newer models have B-pillar handles and even overhead on the ceiling that can be used for some of the top mounting locations. Check to see if you prefer to use these factory locations as the nets typically have enough adjustment to allow for this option. If your vehicle does not have handles in desired locations or you prefer to install mounting points for better fitment, please follow the below steps.

IMPORTANT: READ INSTRUCTIONS FULLY BEFORE STARTING

Overview

Time: About 1 ½ to 2 hours

Paw Level: [rating indicator]

Tools Required (may vary by vehicle)

May Need

Please watch this preliminary video for detail on C100 Mount kit: https://vimeo.com/321352161

Installation Steps

Step 1

Fold down and then forward the back seats to make working easier. Pop off by hand or use panel removal tool to gently lift and remove upper seat belt roller cover.

[Image description: The upper seat belt roller cover, highlighted by a red circle, is shown being gently lifted or popped off.]

Step 2

Unbolt the bolt and drop the seat belt assembly out of the way.

[Image description: A seat belt bolt is shown being unbolted with a wrench, highlighted by a red circle, allowing the seat belt assembly to be moved.]

Step 3

Carefully grasp and pop the lower, darker colored plastic housing covering the wheel well. Watch for any hidden screws and go slowly. Model years can be slightly different from example shown. The lower panel just needs to be loosened, not completely removed from car. Then loosen and remove the top lighter section as shown.

[Image description: Interior plastic trim panels are shown being carefully grasped and popped off, revealing the area behind them.]

Step 4

Exposed C pillar area where the C100M mounts will be installed for the top of the barrier net.

[Image description: The exposed C-pillar area of the vehicle's interior is shown, where the mounting hardware will be installed.]

Step 5

If you have not already, we recommend watching the C100M video for detail on installing these type mounts.

Video: https://vimeo.com/321352161

Step 6

Following guidelines outlined in video regarding double checking depth and avoiding wires and washer lines, install the C100M just above the leading top corner of the side quarter windows.

Driver's side:

[Image description: The installation of a C100M mount just above the leading top corner of the driver's side quarter window is shown, with the mounting point highlighted by a red circle.]

Passenger side:

[Image description: The installation of a C100M mount just above the leading top corner of the passenger side quarter window is shown, with the mounting point highlighted by a red circle.]

Step 7

Once the C100's are installed, test fit the lighter panels and mark and trim (if necessary) inner plastic for strap clearance.

(passenger side shown):

[Image description: The passenger side panel is shown during a test fit. A red circle indicates where inner plastic may need trimming for strap clearance.]

View from inside of the panel:

[Image description: A view from inside the panel shows the trim area highlighted by a red circle, indicating where adjustments for strap clearance might be needed.]

Step 8

Reassemble trim panels with strap and D ring over top of trim.

[Image description: The reassembled trim panel is shown with the net strap and D-ring positioned over the top of the trim, highlighted by a red circle.]

Step 9

Install the upper seat belt bolts with the C1015 brackets installed as shown on the driver's side.

[Image description: The upper seat belt bolt is shown being installed with the C1015 bracket, as seen on the driver's side, highlighted by a red circle.]

Step 10

Install the net loosely, working top to bottom. Top straps to the C100M D rings, middle straps to the C1015 brackets and then lowest straps under the pivot point for the rear seat back upright.

Lower Area:

[Image description: The Raingler net is shown installed loosely in the vehicle's cargo area. Top straps connect to C100M D-rings, middle straps to C1015 brackets, and lower straps are positioned under the rear seat back pivot point.]

Step 11

Do final tensioning from top, then lower (check that the rear seat can raise and lower).

[Image description: The Raingler net is shown being tensioned from top to bottom to ensure a secure fit.]

Step 12

Once net is centered, wrap and tie up the excess ends.

Video showing detail of process: https://vimeo.com/316588617

[Image description: The Raingler net is shown installed, centered, with excess ends wrapped and tied up.]

Step 13

Check out our dog training and introduction tips for success.

Click here to learn more about dog training and safety when using these nets: https://vimeo.com/raingler

Enjoy Your Raingler Net

Enjoy your Raingler Net. Keep your gear stowed safely in back and your pups in place! Let us know if any comment or questions and tag us when you’ve got your net in use and action!

[Image description: A dog is shown sitting comfortably in the cargo area of the Honda CR-V, with the Raingler net installed behind the seats.]

Thank you for purchasing Raingler Nets. If you have any questions please contact us, we are here to help!

See all our install videos on Vimeo! https://vimeo.com/raingler

Models: 2007-2011 Honda CR-V Behind 2nd Row Seats Rear Barrier Divider, 2007-2011, Honda CR-V Behind 2nd Row Seats Rear Barrier Divider, Behind 2nd Row Seats Rear Barrier Divider, 2nd Row Seats Rear Barrier Divider, Row Seats Rear Barrier Divider, Rear Barrier Divider, Barrier Divider, Divider

File Info : application/pdf, 8 Pages, 2.05MB

PDF preview unavailable. Download the PDF instead.

2007 - 2011 Honda CR-V Behind 2nd Row Seats Rear Barrier Divider Net Installation ?v=1663614652

References

Adobe PDF Library 22.2.244

Related Documents

Preview Raingler 2024+ Toyota J250 Landcruiser/GX550 Rear Seat Barrier Net Installation Guide
Step-by-step installation instructions for the Raingler 2024 and newer Toyota J250 Landcruiser and GX550 rear seat barrier divider net. Covers both Upper and Full Height barrier installations.