wifi module_Wireless module_wifi module manufacturer_Shenzhen Chuangling Zhilian wifi module company
Instruction Manual for TROLINK models including: TI7100CB1, TI7100CB1 IOT Module, IOT Module, Module
Shenzhen Trolink Technology Co., Ltd. TI7100CB1 IOT Module 2AYHW-TI7100CB1 2AYHWTI7100CB1 ti7100cb1
File Info : application/pdf, 11 Pages, 1.32MB
DocumentDocumentSHENZHEN TROLINK TECHNOLOGY CO., LTD http://en.tro-link.com/ SPECIFICATION Product Name Model No. Type Version Date IOT Module TI7100CB1 URAT Interface V1.0 2022/2/22 Shenzhen Trolink Technology Co., Ltd Add:2F, B block, The first Techno park of Huafeng, Gushu,Baoan District, Shenzhen, China. Tel0755-88828355/83224500 Website: http://en.tro-link.com/ Email:sales@trolink.cn SHENZHEN TROLINK TECHNOLOGY CO., LTD http://en.tro-link.com/ Content 1. Profile..........................................................................................................3 2. Product Characteristic.............................................................................. 3 3. Product Picture..........................................................................................3 4. Chip Block Diagram...................................................................................4 5. Wireless Module Outline............................................................................4 6. Pin Assignments.........................................................................................5 7. Electrical Characteristic............................................................................6 8. RF Parameter.............................................................................................6 9. DC Consumption........................................................................................7 10. Reference design for PCBA...................................................................7 11. Weld and storage environment ...............................................................8 12. Package details..........................................................................................8 2 SHENZHEN TROLINK TECHNOLOGY CO., LTD http://en.tro-link.com/ 1. Profile TI7100CB1 is an intelligent new generation of highly integrated Wi-Fi and BLE combination chip TG7100C. The wireless subsystem includes 2.4G RF, Wi-Fi 802.11b/g/n and BLE baseband/MAC design. The microcontroller subsystem includes a low-power 32-bit RISC CPU, cache and memory. The power management unit provides flexible settings to achieve low power consumption mode and supports multiple security functions. This Demo board is designed based on TG7100C and can be debugged by JTAG. It provides rich hardware interfaces including UART, PWM, ADC, DAC, I2C, SPI, GPIO, SDIO, etc. 2. Product Characteristic 802.11b/g/n 1*1 standard WiFi+BLE 5.0 Combo, Support STA, Soft AP mode and Sniffer mode Open source independent controllable RISC-V CPU, 1 160MHz adjustable, 276KB SRAM; Ultra long distance, the maximum transmission power is 21dBm, the sensitivity is - 98dBm, and more than one wall is penetrated; High security: support safe startup, safe debugging, AES 128/192/256, Encryption engine, WPA3 ,MD5, SHA-1/224/256', PKA(RSA/ECC) Support the coexistence of Wi-Fi and BLE 3. Product Picture (TOP) (BOTTOM) 3 SHENZHEN TROLINK TECHNOLOGY CO., LTD http://en.tro-link.com/ 4. Chip Block Diagram 5. Wireless Module Outline 4 SHENZHEN TROLINK TECHNOLOGY CO., LTD http://en.tro-link.com/ 6.Pin Assignments NO Pin Name 1 Chip_EN 2 GPIO5 3 GPIO2 4 GPIO11 5 GPIO12 6 GPIO14 7 GPIO17 8 VCC 9 GND 10 GPIO0 11 GPIO8 12 GPIO1 13 GPIO3 14 GPIO4 15 GPIO16 16 GPIO7 Description Chip enable pin (active high) ADC EN GPI011 GPIO12 GPIO14 GPIO17 Power supply 3.3V is required Ground GPIO0 GPIO8 (Boot option) GPIO1 RXD (5V) Communication serial port TXD(5V)Communication serial port RXD(3.3V) Burning serial port TXD(3.3V) Burning serial port 5 SHENZHEN TROLINK TECHNOLOGY CO., LTD http://en.tro-link.com/ 7. Electrical Characteristic Item Description Model No. TI7100CB1 Chipset TG7100C Interface URAT Frequency Band. 2.4 2.483.5MHz WiFi Standard IEEE 802.11b/g/n Modulation Mode Transmit Power 802.11b: CCK, DQPSK, DBPSK 802.11g64-QAM, 16-QAM, QPSK BPSK 802.11n:64-QAM,16QAM,QPSK, BPSK 1,2,5.5,6,11,12,18,22,24,30,36,48,54,65,,72.2Mbps Module Size 35.6*21.6*0.8mm(L*W*H) Working Voltage. DC 5V Encryption method AES 128/192/256 WPA3, MD5.,SHA-1/224/256, PKA(RSA/ECC) Working Temp -230°C to +85°C Storage Temp -55°C to +85°C 8. RF Parameter Transmit power EVM Receiving sensitivity 802.11b:17±1.5dBm 802.11g:15±1.5dBm 802.11n HT20:14±1.5dBm 802.11b: <-20dB@11Mbps 802.11g: <-27dB@54Mbps 802.11nHT20:< -28dB@65Mbps 11b-1Mbps: -98dBm 11b-11Mbps: -91dBm 11g-54Mbps: -77dBm 11n HT20-MCS0: -92dBm 11n HT20-MCS7: -73dBm 6 SHENZHEN TROLINK TECHNOLOGY CO., LTD http://en.tro-link.com/ 9. DC Consumption Test condition: DC3.3V ; Temperature 25 Unit: mA Mode TX/RX Current consumption 802.11b (11Mbps ) TX 132 RX 35 802.11g (54Mbps) TX 120 RX 37 802.11n HT20 (MCS7) TX 108 RX 37 10. Reference design for PCBA Circuit design Requirement about layout of PCB a. RF layout needs to be grounded and 50 ohm impedance 7 SHENZHEN TROLINK TECHNOLOGY CO., LTD http://en.tro-link.com/ 11. Environment about Working and Storage Working Temp Temperature:-30to+85 Relative Humidity:10-90%(non-condensing) Storage Temp Temperature:-55to+85(non-condensing) Relative Humidity:10-90%(non-condensing) Recommended Reflow Profile Heating Stage Temp<150Time6090/sec, Ramp rate: 13/S Preheat Range Temp150200Time60-120/sec, Ramp rate : 0.3-0.8 Reflow Stage Peak temp:235~250(advise peak temp 245Time:30-70 /sec Cooling Stage Temp217~170ramp rate: 35/S . Sn&Ag&Cu Lead-free solder(SAC305) 12. Package details Packed as vacuum reel Reel color: blue Carton size: 33.7cm*33.7cm*9.5cm 2 packs desiccant, 1 pcs humidity card 8 FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules FCC Part 15 Subpart C 15.247 & 15.207 & 15.209 2.3 Specific operational use conditions Operation Frequency:BLE2402~2480MHz WIFI2412~2462MHz Number of Channel:BLE40 Channels WIFI11 Channels Modulation Type:BLEGFSK WIFI802.11b: DSSS (CCK, DQPSK, DBPSK) 802.11g: OFDM (BPSK, QPSK, 16QAM, 64QAM) 802.11n: OFDM (BPSK, QPSK, 16QAM, 64QAM) Antenna Type:PCB antenna Antenna Gain(Peak):3.54 dBi (Provided by customer) The module can be used for mobile or portable applications with a maximum 3.54dBi antenna. The host manufacturer installing this module into their product must ensure that the final composit product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operaition. The host manufacturer has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 2.4 Limited module procedures Not applicable. The module is a Single module and complies with the requirement of FCC Part 15.212. 2.5 Trace antenna designs Not applicable. The module has its own antenna, and doesn't need a host's printed board microstrip trace antenna etc. 2.6 RF exposure considerations The module must be installed in the host equipment such that at least 20mm is maintained between theantenna and users' body; and if RF exposure statement or module layout is changed, then the host product manufacturer required to take responsibility of the module through a change in FCC ID or new application. The FCC ID of the module cannot be used on the final product. In these circumstances, the host manufacturer will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. 2.7 Antennas Antenna Specification are as follows: Antenna Type:PCB antenna Antenna Gain(Peak):3.54 dBi (Provided by customer) This device is intended only for host manufacturers under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna; The module shall be only used with the External antenna(s) that has been originally tested and certified with this module. The antenna must be either permanently attached or employ a `unique' antenna coupler. As long as the conditions above are met, further transmitter test will not be required. However, the host manufacturer is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). 2.8 Label and compliance information Host product manufacturers need to provide a physical or e-label stating "Contains FCC ID 2AYHW-TI7100CB1 With their finished product. 2.9 Information on test modes and additional testing requirements Operation Frequency:BLE2402~2480MHz WIFI2412~2462MHz Number of Channel:BLE40 Channels WIFI11 Channels Modulation Type:BLEGFSK WIFI802.11b: DSSS (CCK, DQPSK, DBPSK) 802.11g: OFDM (BPSK, QPSK, 16QAM, 64QAM) 802.11n: OFDM (BPSK, QPSK, 16QAM, 64QAM) Antenna Type:PCB antenna Antenna Gain(Peak):3.54 dBi (Provided by customer) Host manufacturer must perfom test of radiated & conducted emission and spurious emission, etc according to the actual test modes for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. Only when all the test results of test modes comply with FCC requirements, then the end product can be sold legally. 2.10 Additional testing, Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for FCC Part 15 Subpart C 15.247 & 15.207 & 15.209 and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.