N300 Wireless Router User Manual

Overview

This manual provides instructions for setting up and using the N300 Wireless Router.

Device Label Information:

Wi-Fi Name (SSID): Displayed on the device label.
Username: Default username on the device label.
Password: Default password on the device label.
IP Address: 192.168.10.1

Ports and Buttons

Indicator Lights:
Solid red: Power on. Internet is not connected.
Solid green: Power on. Internet is connected.
Reset/WPS Button: Press for 3s to start WPS. Press and hold for 5s to restore default settings.
LAN Ports: Connect to wired devices.
WAN Port: Connects to the modem.
Power Port: Connects to the power supply.

Connect to Internet

Turn off the modem.
Connect the modem's LAN port to the router's WAN port using an Ethernet cable (RJ45). If your internet connection is via Ethernet cable directly from the wall, connect one end to the router's WAN port.
Connect the power adapter to the router's DC-IN port and turn it on.
Plug in the modem's power adapter.

Set up the Network via a Web Browser

Connect your smartphone or computer to the Wi-Fi name (SSID) displayed on the device label on the router.
Launch a web browser. Enter 192.168.10.1 in the address bar.
Enter the default Username and Password found on the label at the bottom of the router to access the management page.
Navigate to the 'Internet' page, select the WAN Type (DHCP is recommended if unsure), and click 'Save'.
Navigate to the 'WIFI' page. Change the SSID and Password to enhance your Wi-Fi network security. Click 'Save' to apply the configuration.

FAQ

Q1: What should I do if I can't access the router's management page?: Reboot your router and try again. Check your Wi-Fi connection. Use an alternative web browser such as Google Chrome. Restart your computer.
Q2: What should I do if I can't access the Internet?: Reboot your modem and router, then try again. Verify that the Internet is working by connecting the modem directly to a computer with an Ethernet cable.
Q3: What can I do if I forget my wireless network password?: If you haven't changed the default password, it can be found on the label at the back of the router. Alternatively, connect your computer to the router via an Ethernet cable, log in to the web management page at 192.168.10.1, and navigate to 'Install > Wireless' to retrieve or reset your password.
Q4: What should I do if I forget my Web management page password?: Check the Web password on the label at the bottom of the router. If forgotten, use a pin to press and hold the RESET button on the back of the router for approximately 5 seconds until the LED blinks. This will restore the router to its default settings, which can be found on the label.

FCC Warning Statement

FCC Radiation Exposure Statement: The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult a radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Security Warning