Installation Guide for PROSCEND models including: 850G-10I Industrial Ethernet Switch, 850G-10I, Industrial Ethernet Switch, Ethernet Switch, Switch
産業用 10 ポート GbE マネージド スイッチ | 産業用5Gセルラールーターメーカー | PROSCEND
Industrial 10-Port GbE Managed Switch | Industrial 5G Cellular Router Manufacturer | PROSCEND
औद्योगिक 10-पोर्ट जीबीई प्रबंधित स्विच | औद्योगिक 5जी सेल्युलर राउटर निर्माता | PROSCEND
File Info : application/pdf, 1 Pages, 261.06KB
DocumentDocument850G-10I Industrial Ethernet Switch Quick Installation Guide Connecting Power Version: 1.00 The 850G-10I Industrial Ethernet Switch can be powered from two power supplies (input range 24~48VDC). Two power supplies are on the top panel of the switch. Insert the positive and negative wires (AWG 12-24) into V+ and V- contacts on the terminal block respectively and use a flat-head screwdriver to push in and open the wire clamp. First Power Supply Second Power Supply WARNING The DC power should be connected to a well-fused power supply. Alarm Relay and Ground The alarm relay output contacts are shown as ALM next to the DC terminal block connector as the figure below. The alarm relay out is "Normal Open", and it will be closed when it is detecting any predefined failure such as power failures. The relay output with current carrying capacity of 1A @ 24 VDC. The switch must be properly grounded for optimum system performance. LED Indicators LED PWR/RPS ALM RJ45 LAN port Link/Act RJ45 LAN port Speed UPLINK Color On: Green Off On: Red Off On: Green Blinking: Green Off On: Green Off On: Green Blinking: Green Off Description PWR/RPS is powered. PWR/RPS is not powered. Alarm for abnormal power status or function. Normal operation or DIP switch OFF. Ethernet LINK UP. Ethernet traffic detected. Ethernet LINK DOWN. Ethernet LINK UP at 1000Mbps. Ethernet LINK DOWN or LINK UP at 10Mbps/100Mbps LINK UP. Traffic detected. LINK DOWN. Speed LED (Green) Link/Act LED (Green) Speed LED (Green) Link/Act LED (Green) RJ45 Connector Pinouts The pin assignment of RJ45 connector is shown in the following table. Pin Description PoE Pinouts 1,2 T/Rx+, T/Rx- V+ 3,6 T/Rx+, T/Rx- V- 4,5 T/Rx+, T/Rx- X 7,8 T/Rx+, T/Rx- X DIN-rail Mounting STEP 1: Use the screws to install the DIN-rail kit to attach at the rear side of the switch. Ground Connector STEP 2: Hook the unit onto the DIN-rail. STEP 3: Push the bottom of the unit towards the DIN-rail until it locks in place. DIP Switch Setting DIP Function Description 1 (PWR) ON: Primary power alarm reporting is enabled. OFF: Primary power alarm reporting is disabled. 2 (RPS) ON: Redundant power alarm reporting is enabled. OFF: Redundant power alarm reporting is disabled. Reset Button Function Reboot Reset to factory default Operation Press the Reset button for 2 seconds and release. Press the Reset button for 10 seconds and release. Reset Web Interface: Connect & Login 1. Factory default IP: 192.0.2.1 2. Login with default account and password. Username: root Password: 2wsx#EDC NOTE Please scan below QR Code to download online resources. Download Link: https://www.proscend.com/en/product/850G-10I.html Proscend Communications Inc. All rights reserved. - 1 - 850G-10I www.proscend.com
PROSCEND is a leading global provider of mission-critical Internet of Things (IoT) connectivity products, services, and solutions with high levels of reliability and security.PROSCEND is a leading global provider of mission-critical Internet of Things (IoT) connectivity products, services, and solutions with high levels of reliability and security.Industrial 10-Port GbE Managed Switch | Industrial 5G Cellular Router Manufacturer | PROSCEND