WIRELESS HEADPHONES

Product Overview

The image displays a pair of black over-ear wireless headphones. The left earcup is shown from the side, featuring buttons. The right earcup is shown from the top, indicating various ports and lights. The headphones have a padded headband and earcups.

Key Components:

• 1. Power Button
• 2. Volume + / Next
• 3. Volume - / Previous
• 4. ANC / Bass Boost Button
• 5. LED Indicator Light
• 6. Microphone
• 7. 3.5mm AUX Audio Port
• 8. Charging Port

Safety Warnings

Headphones can deliver sounds at loud volumes and high-pitched tones, potentially causing permanent hearing loss or damage. Volume levels may vary. It is recommended to use the lowest possible volume and avoid noisy environments. If discomfort or ringing occurs, discontinue use and consult a physician. Continued high volume use can lead to permanent hearing damage without noticeable discomfort.

CAUTION: Using headphones while operating vehicles or engaging in activities requiring full attention may be dangerous and illegal. Consult a physician before use if you have a pacemaker or other electrical medical devices. Do not attempt to dismantle the product; this may cause short circuits, fire, or electric shock. Components are not user-replaceable. Avoid exposing the product to rain, moisture, or liquids. Discontinue use if the product overheats, is dropped, or submerged in liquid. Dispose of the product according to local standards and regulations. When disconnecting power cords, grasp the plug, not the cord. Never use a damaged charger.

Battery Disposal: Batteries cannot be replaced by the user. Warning: Do not touch leaking battery fluid, as it may be corrosive or toxic. Wear protective gloves if battery leakage is detected and dispose of safely. In case of contact with skin or eyes, rinse immediately with clean water and seek medical assistance.

CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS: Do not dispose of batteries in fire or hot ovens, or crush/cut them. Do not leave batteries in extremely high or low temperature environments, as this can result in explosion or leakage.

• High sound pressure
• Hearing damage risk
• Do not listen at high volume levels for long periods

FCC Information

This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Button Controls

Charging The Battery

Before first use, it is recommended to charge your headphones for a minimum of 2 hours.

1. Insert the small end of the included USB-C cable into the USB-C connector on the headphone's right ear cup.
2. Connect the other end of the charging cable to a USB-A port on your PC, laptop, wall outlet adapter or other charging devices.
3. The LED light will show a solid red colour to indicate charging is active.
4. The light will turn off when fully charged.

NOTE:

• Charge only with 5V DC Max 1A input.
• Use only the original USB-C charging cable to avoid any damage.
• When the LED flashes red, this indicates the headphones battery is low and requires charging.

Battery Care

• Make sure that your headphones are switched OFF after use.
• Do not leave a fully charged battery connected to a charger, since overcharging may shorten its lifetime.
• Before storing the headphones for long periods of time, be sure to fully charge the battery.
• When the battery is low and flashing red, you must charge the headphones.
• If the battery is completely discharged, the headphones cannot be turned on immediately when the charger is connected. Allow a depleted battery to charge for a few minutes before turning on the headphones.
• Always try to keep the battery between 32°F and 113°F. A product with a hot or cold battery may not work temporarily, even when the battery is fully charged.

Operation

Power On/Off

1. Press and hold the power button for three seconds.
2. When powered on successfully, a tone will be heard and the LED indicator lights will illuminate.
3. To power off, press and hold the power button for three seconds; a tone will be heard and the LED indicator light will turn off.

NOTE: If there is no operation within 5 minutes after powering on, the unit will turn off automatically.

Pairing

1. With your headphones powered on, the indicator light will flash red and blue to indicate pairing mode.
2. Enable Bluetooth on your device, search for and select CE220818 from the list to connect.
3. Once successfully paired, you will hear a tone, and the LED light will turn off, indicating a successful connection.

NOTE: On first use, the headphones should automatically enter pairing mode.

Listening To Your Device

Once paired, you can play, pause, skip tracks, and adjust the volume using the headphone controls or device controls.

Using The AUX Port

The AUX port can be used to connect to a non-wireless device or for listening to music when headphone batteries are drained.

1. Connect a 3.5mm audio cable to the aux-in jack located on the right earcup.
2. Connect the other end of the audio cable to the audio jack.

NOTE: When connected via audio cable, Bluetooth function and controls are disabled. Playback cannot be controlled using headphone controls when connected via aux-in. The headphones will not be discoverable on Bluetooth.

Specifications

• Bluetooth Version: 5.4
• Bluetooth Distance: 10m
• Battery Capacity: 500mAh
• Play Time: ANC On: 30 hours with 50% volume; ANC Off: 60 hours with 50% volume
• Standby Time: 300 hours
• Charging Time: 2.5 hours
• Power Input: DC 5V, 500mA
• Driver Size: 40mm
• Operation frequency band: 2402MHz – 2480MHz
• Maximum radio-frequency power transmitted: less than 20dBm

Warranty

Please contact the store where you purchased the item for any warranty issues.

Warranty Conditions

Dear Customer, The BAUHN warranty is a full warranty offering the following benefits:

Warranty Period: 3 years from date of purchase.

The warranty does not cover damage caused by:

• Accident or unanticipated events (e.g. lightning, water, fire).
• Improper use or transport.
• Failure to follow the safety and maintenance instructions.
• Other improper treatment or modification of the product.

After the expiration of the warranty period, you may wish to have your product repaired at your own expense. You will be notified of the repair costs in advance.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state, but this warranty is not intended to exceed statutory minimum requirements beyond what is included above.

This warranty does not limit the statutory obligation of the seller arising from any implied warranties. The period of warranty can only be extended in accordance with applicable law.

Neither the service company nor BAUHN will assume any liability for data or settings stored on any returned product.