Lightning McQueen Car II Toddler Bed

Important Safety Information

Assembly Requirements:

• Assembly must be carried out by a competent adult only.
• Keep children away from the product during assembly due to the risk of injury.
• Assemble the furniture on a soft, level surface to prevent damage to the product or floor.
• It is recommended to assemble the furniture near its final placement to avoid unnecessary moving once assembled.
• If moving the furniture, remove all loose items and get assistance to lift it. Dragging the furniture will cause damage.
• Ensure fingers and legs are clear of all adjustments during assembly.
• Regularly check and re-tighten all bolts.

Product Suitability:

• Suitable for children aged 18 months to 4 years.
• Maximum weight allowed on the product: 60 kg.

Care and Maintenance:

• Avoid placing hot items directly on the surface; use insulation like placemats or coasters. Heat can cause discoloration or damage.
• Clean the surface with a soft cloth dampened with water.
• Do not use abrasive cleaners, furniture wax, or polish, as they may damage the surface.
• Caution: Frequent exposure to direct sunlight or similar sources may cause discoloration or fading.

Specific Safety Warnings:

• Window Safety: Do not place near a window as a child might use it as a step and fall out.
• Fire/Heat Safety: Be aware of the risk of open fires and other strong heat sources nearby.
• Strangulation Hazard: Do not place near windows where blind or curtain cords could strangle a child.
• Use only additional or replacement parts obtained from the manufacturer or distributor.
• Do not use if any part is broken, torn, or missing.
• Ensure the bed is placed either directly against a wall or with a 300mm gap between the wall and the side of the bed.
• Use a mattress that is 140cm long and 70cm wide.
• The bed conforms to BS8509:2008 + A1:2011.
• The bed is designed to be dismantled for storage and transportation.

Parts List

Diagram showing various wooden panels and supports labeled 1 through 16.

• Part 1: Left front side panel with wheel arch detail.
• Part 2: Right front side panel with wheel arch detail.
• Part 3: Left rear side panel with wheel arch detail.
• Part 4: Right rear side panel with wheel arch detail.
• Part 5: Left lower side frame.
• Part 6: Right lower side frame.
• Part 7: Front lower crossbar.
• Part 8: Front upper crossbar.
• Part 9: Middle crossbar/support.
• Part 10: Rear lower crossbar.
• Part 11: Mattress support slats (multiple pieces).
• Part 12: Central vertical support for mattress base.
• Part 13: [Not explicitly used in assembly steps].
• Part 14: [Not explicitly used in assembly steps].
• Part 15: Rear end panel.
• Part 16: Front end panel.

Hardware List

Diagram showing various screws, bolts, and connectors labeled A through H.

• Hardware A: M6 x 40mm screw (x6)
• Hardware B: M6 x 45mm screw (x16)
• Hardware C: M6 x 20mm screw (x16)
• Hardware D: 10 x 10.5mm screw (x26)
• Hardware E: M6 x 35mm screw (x10)
• Hardware F: 10 x 10.3mm screw (x14)
• Hardware G: M6 x 25mm screw (x22)
• Hardware H: Connector/Dowel (x2)

Assembly Steps

Note: Assembly requires 2 people for most steps.

Step 1

Attach part 2 to part 1 using 4x hardware F and 2x hardware H. ? 2 People Required.

Step 2

Attach parts 1 and 2 to part 4 using 3x hardware B, 3x hardware D, and 2x hardware G. ? 2 People Required.

Step 3

Attach part 3 to parts 1 and 4 using 3x hardware B, 3x hardware D, and 2x hardware G. ? 2 People Required.

Step 4

Attach part 9 to part 7 using 2x hardware B, 2x hardware D, and 2x hardware G.

Step 5

Attach parts 9, 7, 8, and 10 using 6x hardware E, 6x hardware F, and 6x hardware G.

Step 6

Attach part 6 to parts 7, 8, 9, and 10 using 4x hardware B, 4x hardware D, and 3x hardware G. ? 2 People Required.

Step 7

Attach parts 5 and 6 to part 10 using 4x hardware B, 8x hardware D, and 3x hardware G. ? 2 People Required.

Step 8

Attach parts 3, 4, 5, and 6 using 4x hardware G, 4x hardware F, and 4x hardware E. ? 2 People Required.

Step 9

Attach part 12 to the bed frame using 4x hardware C.

Step 10

Attach part 12 to the bed frame using 4x hardware C.

Step 11

Attach part 11 (slats) to the bed frame using 6x hardware A and 6x hardware D. ? 2 People Required.

Step 12

Attach parts 15 and 16 to the bed frame using 8x hardware C.