User Manual for DATECS models including: EP700, YRW-EP700, YRWEP700, EP-700 Highest Class ESC POS Printer, EP-700, Highest Class ESC POS Printer, Class ESC POS Printer, ESC POS Printer, Printer
DATECS LTD. EP700 EP-700 YRW-EP700 YRWEP700 ep700
1 DATECS EP-700 User Manual 1 DATECS Version Data Range 1.0.0 12.05.2025. All document 1.1.0 15.05.2025. Regulatory EP-700 Change description First release Updated section "Regulatory" User's Manual Author Stefan Derev Stefan Derev UM 07.01.84/v1.1.0 2 1 DATECS EP-700 User's Manual THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM DATECS LTD. UM 07.01.84/v1.1.0 3 1 DATECS EP-700 Regulatory User's Manual FCC Statement FCC ID: YRW-EP700 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. UM 07.01.84/v1.1.0 4 1 DATECS EP-700 User's Manual 1. Introduction EP-700 is the highest-class ESC/POS printer. It is designed to support large retail points of sales and services offering RS 232, USB, Bluetooth, Wi-Fi and Ethernet connectivity. UM 07.01.84/v1.1.0 5 1 DATECS EP-700 User's Manual 2. Technical and functional specifications Parameter Printing Mechanism Printing Width Printing Resolution Printing Speed Printable Font Sizes Printable Barcode Types Paper Type Paper Width Paper Thickness Roll Max Diameter Paper loading Post Printing Features Operator Display Emulations Connectivity LED Indication Keyboard and Buttons Power supply Reliability Certificates Dimensions (W x D x H) Comments Direct line thermal printer 80 mm (640 dots) 203 x 203 dpi (8 x 8 dpmm) Max 200 mm per second Font A 12 x 24 dots Font B 9 x 24 dots Font C 8 x 16 dots 1D: EAN-13, EAN-8, Code 39, Code 128, Interleaved 2 of 5, Codabar Thermal paper rolls 82 and 58 mm 60 to 150 m 102 mm Easy paper loading Auto cutter Graphic LCD, 4 lines x 22 characters (128x32) LED Back Light ESC/POS RS 232C USB 2.0 compatible Bluetooth Classic 3.0 (Optional) Bluetooth Low energy and Classic 4.2 (Optional) Wi-Fi 802.11 b/g/n (Optional) LAN 10/100 Mbps (100BASE-TX) Cash Drawer through RJ11 connector External Display through RJ11 connector SAM Slot Paper end Cover open On/Off button Feed button 4 function buttons AC 100 to 240 V, 50 to 60 Hz, DC 24 V, 2.1 A 150 km 1.5 million cuts (Auto cutter) CE, FCC 150 x 185 x 130 mm Weight Operational temperature range Storage temperature range 1 700 g -10 to 40 °C, 35 to 85 % RH -20 to 60 °C, 10 to 90 % RH UM 07.01.84/v1.1.0 6 1 DATECS 3. Device operation EP-700 User's Manual 1. 220V Power supply 2. Drawer 3. Display 4. USB Type B Port 5. RS232 Port 6. Ethernet 7. Display and control panel 8. Open top cover button 9. Power On/Off button UM 07.01.84/v1.1.0 7 1 DATECS 4. Control panel and buttons EP-700 User's Manual 4.1. Buttons functions Button - Power ON/OFF the printer Function - If there is no selected menu and the printer is in working state feeds paper - If a menu is selected, enter the selected option - If no menu is selected and the printer is in working state, hold for 2-3 sec - prints the Ethernet and Wi-Fi info - If a menu is selected - exit from the selected option - If no menu is selected and the printer is in working state hold for 2-3 sec to enter the main menu - if main menu is open goes to next line - If no menu is selected and printer is in working state hold for showing the WiFi info - If a menu is selected, it goes to the next line - If a parameter from the menu is selected, the value is decreased - If no menu is selected and printer is in working state hold for showing the Ethernet info - If a menu is selected, it goes to the previous line(option) - If a parameter from the menu is selected, the value is increased UM 07.01.84/v1.1.0 8 1 DATECS 5. Main menu EP-700 User's Manual To enter the main menu, hold button for 2-3 seconds. To move through the menu use and buttons. To enter a menu press button. To exit a menu press button. 5.1. Common settings 5.1.1 Printer name 5.1.2 LCD off time 5.2 Print settings 5.2.1 Darkness 5.2.2 Print speed 5.2.3 Print width 5.2.4 Code page 5.3 Communications 5.3.1 Flow control 5.3.2 RS-232 5.3.3 Wireless 5.3.4 Bluetooth information 5.3.5 Bluetooth pair 5.4 Ethernet 5.4.1 IP address 5.4.2 Port 5.4.3 Subnet mask 5.4.4 Gateway 5.4.5 DNS 5.4.6 DHCP 5.4.7 DHCP target name 5.5 Print server 5.5.1 Server mode 5.5.2 Job timeout 5.6 Switches SW1 Enable sound SW2 Execute CR as LF SW3 Disable LF SW4 Disable LF after CR SW5 Default small font SW6 Narrow paper SW7 Black mark mode SW8 Xon / Xoff SW9 Delayed print SW10 Not used SW11 Protocol mode SW12 Disable cutter SW13 Ext. display selected UM 07.01.84/v1.1.0 9 1 DATECS 5.7 Diagnostic 5.7.1 Short 5.7.2 Full 5.7.3 Test mode 5.8 Set clock 5.9 Factory reset 5.10 Save settings EP-700 User's Manual UM 07.01.84/v1.1.0 10 1 DATECS EP-700 6. Power ON/OFF the printer The ESC/POS printer can be powered ON by pressing the button. The ESC/POS printer can be powered OFF by pressing and holding the 7. Changing the paper roll The ESC/POS printer has easy paper loading function. If you want to change the paper roll: - Open the cover - Put the paper roll - Move 3 to 5 cm from the paper - Close the cover - Press button if you want to move the paper. User's Manual button. UM 07.01.84/v1.1.0 11 1 DATECS 8. Bluetooth and Wi-Fi EP-700 ESC/POS Printer EP-700 provides Bluetooth and Wi-Fi communication. User's Manual On the connected device (COTS or PC) a special application must be installed for working with ESC/POS EP-700 Printer. For more information, please contact your distributor. UM 07.01.84/v1.1.0 12 1 DATECS EP-700 User's Manual 9. Work with system The ESC/POS printer must be connected to a PC, tablet, telephone or some other device via USB, RS232 or LAN. The ESC/POS printer executes commands that are sent by user's application. UM 07.01.84/v1.1.0 13 1 DATECS 10. Safety EP-700 User's Manual Please contact with your local Datecs representative or service provider to receive a spare original battery. Don't leave ESC/POS Printer for long time without main battery, otherwise cryptographic keys can be deleted. · To prevent damage to your device's parts or internal circuits, do not use it in dusty, smoky, damp, or dirty environments or near magnetic fields. · Using an unapproved or incompatible power adapter, charger, or battery may damage your device, shorten its lifespan, or cause a fire, explosion, or other hazards. · Keep the device and battery away from excessive heat and direct sunlight. Do not place them on or in heating devices, such as microwave ovens, stoves, or radiators. · Dispose the battery, and accessories according to local regulations. They should not be disposed of in normal household waste. Improper battery use may lead to fire, explosion, or other hazards. · Do not use, store or transport the device where flammables or explosives are stored (in a gas station, oil depot, or chemical plant, for example). Using your device in these environments increases the risk of explosions or fire. 10.1. Service and Support For ESC/POS printer problems, product service, and repair information, contact your local Datecs representative or service provider. · International Contact your local Datecs distributor 10.2. Service Returns All customers, please contact your local Datecs Ltd representative or distributor for assistance with your service, return, or replacement. 10.3. Maintenance and Cleaning ESC/POS Pritner units have no user-serviceable parts. To clean the unit, use a clean cloth slightly dampened with water and a drop or two of mild soap. For stubborn stains, use alcohol or an alcohol-based cleaner. Do not attempt to clean the card readers. Doing so can void any warranty. For card reader service, contact your Datecs distributor or service provider. UM 07.01.84/v1.1.0 14 1 DATECS EP-700 User's Manual Never use thinner, trichloroethylene, or ketone-based solvents they can deteriorate plastic or rubber parts. Do not spray cleaners or other solutions directly onto the display. UM 07.01.84/v1.1.0 15Microsoft Word for Microsoft 365