philio-tech.comphilio-tech.com/
User Manual for Philio models including: PSR05, Zigbee Remote Control, PSR05 Zigbee Remote Control
It is the Zigbee product, it support the security, OTA... Those newest features of the Zigbee technology. Zigbee is a wireless communication.
Download — Philio Technology
File Info : application/pdf, 6 Pages, 232.19KB
DocumentDocumentZigbee Remote PSR05 CAUTION replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types); disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion; leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas The marking information is located at the bottom of the apparatus. The Remote PSR05 is a simple control can controls 8 groups scene, based on Zigbee technology. It is the Zigbee product, it support the security, OTA... Those newest features of the Zigbee technology. Zigbee is a wireless communication protocol designed for home automation, specifically to remotely control applications in residential and light commercial environments. The technology uses a low-power RF radio embedded or retrofitted into home electronics devices and systems, such as lighting, home access control, entertainment systems and household appliances. Specification Rated DC3.7V Lithium rechargeable battery Charger Voltage 5Vdc from Micro USB RF distance Min. 40M indoor, 100M outdoor line of sight, Frequency Range 2405MHz~2480MHz RF Maximum Power +5dBm Location Indoor use only Operation temperature -10 to 45° C Humidity 95% RH max Dimension 110(L) x 110(W) x 19(H) mm Specifications are subject to change improvement without notice. and Troubleshooting Symptom Cause of Failure The device can not join to Zigbee network The device may in a Zigbee network. Recommendation Reset the device then include again. For Instruction to http:// www.philio-tech.com Overview Adding to Z-WaveTM Network There are two tamper keys in the device, one is in the back side, another is in the front side. They have the same function. Both of them can joining network, reset from Zigbee network. In the first time, add the device into the Zigbee network. First, make sure the primary controller is in the inclusion mode. And then power on the device, just take out the insulation Mylar in the back side of the device. The device will auto start the try joining network mode. And it should be included in 120 seconds. You will see the LED light ON one second. * Joining network: 1. Have Zigbee Controller entered inclusion mode. 2. Hold down the central key, then press the top-right key three times within 1.5 seconds to enter the add mode. * Reset to default: 1. Hold down the central key, then press the top-right key four times within 1.5 seconds and do not release the top-right key in the 4th pressed, and the LED will light ON. 2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the keys. If successful, the LED will light ON one second. Otherwise, the LED will flash once. 3. IDs are remove and all settings will reset to factory default. Zigbee IAS-ZONE While the device is associated with a Zigbee network: · The PSR05 will try to find the CIE and ZCL ALARM client. · When press the button the device will send scene function number. PSR05 will snd "ZCL Alarm command" to Alarm and CIE client. Function Control PSR05 has five keys on the device. The central one has group-button switching and special function, the others are control keys. There are two group-buttons that can be switched by pressing central key. When the device is switched to group-button 1, LED will light on with red color for 3 seconds. When the device is switched to groupbutton 2, LED will light on with green color. * Scene Control The device is in group-button 1, When press the button the LED will light the red color. The device is in group-button 2, When press the button the LED will light the green color. Scene Control Key: Top-left Command: 0x01 Key: Top-right Command: 0x02 Key: Bottom-left Command: 0x03 Key: Bottom-right Command: 0x04 Group-Button 1 Group-Button 2 Key: Top-left Command: 0x05 Key: Top-right Command: 0x06 Key: Bottom-left Command: 0x07 Key: Bottom-right Command: 0x08 Zigbee Message Report When device is charging, it will send Wake Up Notification to controller minutely. * Battery Power Check When any keys around the central key is pressed, the device will check the battery power. If the power level is too low, the red LED will flash once after pressing. Please charge the device through micro USB immediately. * Network State Check When the power on, the device will check the network state. If the device join network , the LED will steady off. If doesn't, The LED will flash in every second and continue 30 seconds. * Low Battery Report: When the battery level is too low, than press the button, the device will report the trigger event and also report the battery status. Alarm (Cluster ID : 0x0009) AlarmCluster : 0x0001 AlarmCode : 0x01 Activate the power The device can not work normally in the first time. Please activate the battery through micro USB before the first use. After the device is activated by connecting to micro USB, the device will start charging and LED will light on with red color. If the battery is full charged, LED will light on with green color. * Try joining network When the power on, the device will check is it already adding to the network? If doesn't, it will auto start the joining network mode. Until timeout or the device joined network. Over The Air (OTA) Firmware Update The device support the Zigbee firmware update via OTA. Before starting the procedure, please remove the front cover of the device. Otherwise the hardware check will be failed. The Device will find the OTA server in the network. The OTA server will provide the necessary information to device. The device will decide if the OTA is necessary. Disposal This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. Company of License HolderPhilio Technology Corporation Address of License Holder8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City 24257, Taiwan(R.O.C) www.philio-tech.com FCC Interference Statement that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from Warning Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new once, the retailer is legally obligated to take back your old appliance for disposal at least for free of charge. :